REPLACEMENT PUMPS OWNER’S MANUAL INSTALLATION, OPERATION & PARTS NE4517 NE4518 NE4519 NE4520 NE4521 NE4522 NE4513 NE4514 NE4515 NE4516 NEP4208 NE4523 NEP4268 NEP4269 NE4524 NEP4271 VER.
IMPORTANT – READ CAREFULLY NOTE – To prevent potential injury and to avoid unnecessary service calls, read this manual carefully and completely. SAVE THIS INSTRUCTION MANUAL Use of unauthorized replacement parts voids warranty. ATTENTION INSTALLER – THIS MANUAL CONTAINS IMPORTANT INFORMATION ABOUT THE INSTALLATION, OPERATION, AND SAFE USE OF THIS PUMP THAT MUST BE FURNISHED TO THE END USER OF THIS PRODUCT. FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS COULD RESULT IN SERIOUS INJURY.
Locate cord to prevent abuse from lawn mowers, hedge trimmers and other equipment. WARNING – Connect only to a grounding type receptacle protected by a Ground Fault Circuit Interrupter (GFCI). Contact a licensed electrician if you cannot verify that the receptacle is protected by a GFCI. WARNING – Failure to bond pump to pool structure will increase risk for electrocution and could result in injury or death.
- In addition to two or more suction outlets per pump installed in accordance with latest IAF (formerly NSPI) standards and CPSC guidelines, follow all national, state, and local codes applicable. - Installation of a vacuum release or vent system, which relieves entrapping suction, is recommended. WARNING – Hazardous Pressure. Pool and spa water circulation systems operate under hazardous pressure during start-up, normal operation, and after pump shut-off.
Installation Instructions WARNING – This product should be installed and serviced only by a qualified professional. Pump Location Locate pump as close to pool as practical and run suction lines as direct as possible to reduce friction loss. Suction lines should have continuous slope upward from lowest point in line. Joints must be tight (but not over-tightened). Suction line diameter must equal or be larger than the discharge line diameter.
prevent leakage. Tighten fitting by hand and then use a tool to engage fitting an additional 1 ½ turns. Use care when using Teflon tape as friction is reduced considerably; Do NOT over-tighten fitting or you may cause damage. If leaks occur, remove fitting, clean off old Teflon tape, re-wrap with one to two additional layers of Teflon tape, and re-install fitting. Fittings Fittings restrict flow. For better efficiency, use the fewest possible fittings (but at least two suction outlets).
Voltage Voltage at motor MUST NOT be more than 10% above or below motor name plate rated voltage, or motor may overheat, causing overload tripping and reduced component life. If voltage is less than 90% or more than 110% of rated voltage when motor is running at full load, consult Power Company. Grounding and Bonding Install, ground, bond, and wire motor in accordance with local or national electrical code requirements. Permanently ground motor.
Fill strainer housing with water to suction pipe level. NEVER OPERATE THE PUMP WITHOUT WATER. Water acts as a coolant and lubricant for the mechanical shaft seal. WARNING – If pump is being pressure tested (40 PSI MAXIMUM), be sure pressure has been released, using the filter manual air relief valve, before removing strainer cover. CAUTION – NEVER run pump dry. Running pump dry may damage seals, causing leakage, flooding, and voids warranty. Fill strainer housing with water before starting motor.
replace as necessary. Pumps have self-lubricating motor bearings and shaft seals. No lubrication is necessary. Keep motor clean. Insure air vents are free from obstruction to avoid damage. Do NOT use water to hose off motor. Occasionally, shaft seals must be replaced, due to wear or damage. Replace with genuine seal assembly kit. See “Shaft Seal Change Instructions” in this manual. Storage/Winterization WARNING – Separation Hazard. Do not purge the system with compressed air.
B. Disconnect all electrical power service to pump before beginning shaft seal replacement. C. Only qualified personnel should attempt rotary seal replacement. Contact your local authorized Dealer or service center if you have any questions. D. Exercise extreme care in handling both the rotating and the stationary sections of the two-part replacement seal. Foreign matter or improper handling will easily scratch the graphite and ceramic sealing surfaces.
Solution: Tighten, repair, or replace valves. 4. Strainer basket or skimmer basket loaded with debris. Solution: Remove strainer housing cover or skimmer cover, clean basket, and refill strainer housing with water. Tighten cover. 5. Suction side clogged. Solution: Contact a qualified repair professional. Block off to determine if pump will develop a vacuum. You should have 5”-6” of vacuum at the strainer cover (Only your pool dealer can confirm this with a vacuum gauge).
4. Motor bearings noisy from normal wear, rust, overheating, or concentration of chemicals causing seal damage which will allow chlorinated water to seep into bearings wiping out the grease causing bearing to whine. Solution: All seal leaks should be replaced at once. TECHNICAL DATA B.W.No. HTA/HTI HP Voltage Hertz Amps Flow Rate NE4517 HTI100 1.0 115/230 60 13/6.5 86GPM NE4518 HTI150 1.5 115/230 60 15/7.5 90GPM NE4519 HTI2SP075 0.75/0.23 230 60 5 /1.
FX PRO II NE4517,NE4518,NE4519,NE4520,NE4521,NE4522 PUMP SERIES PARTS BREAKDOWN Key 1 2 3 4 5 6 7 8 8 8 8 9 10 11 12 12 12 12 12 12 13 Part Name LID W/TRANSPARENT COVER O-RING BASKET STRAINER DRAIN PLUG DRAIN PLUG O-RING O-RING DIVERSION SETS IMPELLER OF ITEM#HTI 075/HTI2SP 075 IMPELLER OF ITEM#HTI 100/HTI2SP 100 IMPELLER OF ITEM#HTI 150/HTI2SP 150 IMPELLER OF ITEM#HTI 200/HTI2SP 200 O-RING PUMP HOUSING SCREW MOTOR OF ITEM#HTI 100 MOTOR OF ITEM#HTI 150 MOTOR OF ITEM#HTI2SP 075 MOTOR OF ITEM#HTI2SP 100 MOTO
FX PRO II NE4513,NE4514,NE4515,NE4516, NEP4208 PUMP SERIES PARTS BREAKDOWN Key 1 2 3 4 5 6 7 8 9 10 11 12 13 Part Name LID TRANSPARENT COVER O-RING BASKET CLAMP STRAINER DRAIN PLUG DRAIN PLUG O-RING O-RING SCREW PUMP COVER O-RING IMPELLER OF ITEM#HTA 075/HTA2SP075 075 IMPELLER OF ITEM#HTA 100/HTA2SP100 100 IMPELLER OF ITEM#HTA 150/HTA2SP150 150 PUMP HOUSING MOTOR OF ITEM#HTA 075 MOTOR OF ITEM#HTA 100 MOTOR OF ITEM#HTA2SP 075 MOTOR OF ITEM#HTA2SP 100 MOTOR OF ITEM#HTA2SP 150 Manf. No.
FX PRIME SINGLE SPEED PUMPS TECHNICAL DATA Model HP Voltage Hertz Amps Flow Rate GPM NE4523 0.75 115 60 5.5 38GPM NF4268 0.33 115 60 2.5 24GPM NEP4269 0.50 115 60 4.5 35GPM NE4524 1.50 115 60 15.5 115GPM NEP4271 1.0 115 60 11.0 90GPM FX PRIME SINGLE SPEED NE4523, NEP4268, NEP4269 PUMP SERIES PARTS BREAKDOWN 7 Key 1 2 3 Part Name Water Pump/ Motor Transparent Hair & Lint Strainer 41 1Cover 1/4"- 1 1/2" Hose Connector Qty 1 1 2 Manf. No. B.W. No.
