User Guide

ManualsBrandsFluidmaster ManualsToilet Repair Kits550DFRK

Water Saving

Refill Module

Fluidmaster’s Patent-

Pending Water Saving

Refill Module boosts

performance when

combined with

Fluidmaster’s PerforMAX

FILL VALVE 400ARHR.

Step 2: Remove the tank

lid. Mark the current

water level in your tank.

Flush your toilet once.

Make a mark at the

residual water level left

inside the tank. Flush your

toilet a second time to drain

the water from the toilet

tank. If necessary, sponge

out any remaining water.

RESIDUAL

WATER LEVEL

CURRENT

WATER LEVEL

Items Needed

- Sponge or Towel

- Pliers (Optional)

- Pencil

Step 3: Remove the

existing flapper, chain and

flush handle assembly

from your tank. When

removing the FLUSH

HANDLE, note that the

LOCK NUT may be

reverse-threaded, so you

need to turn it clockwise

to loosen it.

Step 4:

Remove the old

fill valve assembly.

DUO FLUSH

VALVE OVERVIEW & PREPARATION INCOMPATIBILITIES / SPECIAL NOTES SHUT OFF WATER

SECTION 1: MARKING WATER LEVELS & REMOVING OLD PARTS IDENTIFYING YOUR FLUSH VALVE SEAT

Adjustment

Dials

Roller

Clamp

Dual

Action

Handle

Flush

Cable

Flush

Handle

Actuator

PerforMAX

Fill Valve

Refill Tube

Overflow

Pipe

Overflow

Hose

Overflow

Hose Clip

Snap-On

Mount

Flush

Valve

Seat

Step 1: Shut off the

water supply beneath

your toilet by turning the

valve clockwise.

CLOCKWISE

REMOVE

OLD

FILL VALVE

PARTS OVERVIEW

There are 5 main

components

included in this

box. Each of

these

components are

contained within

color-coded bags

with a

corresponding

letter.

To identify a part

within the box,

look for the

letter and color

on each bag that

corresponds with

the parts listed

to the right.

Dual Action Handle (Handle)

The DUAL ACTION HANDLE will allow you to flush

UP for a half flush and DOWN for a full flush.

PART

Brass Seat Adapter

The BRASS SEAT ADAPTER is only necessary

if you have a BRASS FLUSH VALVE SEAT.

PART

DUO FLUSH

Valve

The DUO FLUSH

Valve saves water by

allowing you to choose between half and full

flushes.

PART

Angled Seat Adapter

The ANGLED SEAT ADAPTER is only necessary if

you have a plastic ANGLED FLUSH VALVE SEAT.

PART

PerforMAX

Fill Valve

The PerforMAX

Fill Valve maximizes system perfor-

mance. It replaces the fill valve currently in your tank.

PART

INSTALLATION GUIDE

DUO FLUSH

30800 Rancho Viejo Rd.,

San Juan Capistrano, CA 92675

www.fluidmaster.com

800.631.2011

Visit www.duoflush.com for

easy-to-follow installation videos

and additional troubleshooting tips.

CLOCKWISE

TO LOOSEN

LOCK NUT

REMOVE

FLUSH HANDLE

AND FLAPPER

PART# 25-0173, Grev. 3, 12/11

System

Step 5A: Identify the

type of FLUSH VALVE

SEAT you have in your

tank. If your plastic

OVERFLOW PIPE has a

FLAT SEAT as pictured

above, proceed to Section

4 on the back side of this

instruction guide.

This device is not intended to be used as a retrofit device for

1.28 gpf water closet.

Performance may vary since product was not tested on all

models of water closets.

Step 5B: If your plastic

OVERFLOW PIPE has an

ANGLED SEAT, locate and

remove the ANGLED SEAT

ADAPTER from the yellow

bag labeled “B.” Follow

the installation

instructions below for

SECTION 2.

Step 5C: If your

OVERFLOW PIPE is brass,

locate and remove the

BRASS SEAT ADAPTER

from the orange bag

labeled “C.” Follow the

installation instructions

below for SECTION 3.

BRASS SEAT

FLAT SEAT

ANGLED SEAT

3”

Flush Valves

3”

Certain 1-piece toilets

with Low-Boy tanks

(less than 8” in height)

Kohler Side-

Mount Valves

Requires installation of 2" flapper

flush valve (not included).

Can be replaced with

Fluidmaster’s 507 Flush Valve.

Ballcock

Fill Valves

Mansfield

Flush

Valves

Can be replaced with

Fluidmaster’s PerforMAX

FILL

VALVE 400ARHR.

The systems and components shown here are not

compatible with the Fluidmaster DUO FLUSH

Valve.

Step 12: Wipe down the

BRASS FLUSH VALVE SEAT

before installing to check

for mineral build-up. If

the OVERFLOW PIPE is

threaded on (some are,

some aren’t) make sure

it’s tight by twisting

clockwise before

installing the BRASS SEAT

ADAPTER.

SECTION 2: INSTALLING THE ANGLED SEAT ADAPTER

Step 6: Prior to installing the

ANGELED SEAT ADAPTER

make sure the bottom of the

tank and flush valve seat are

dry.

Step 7: Remove paper from

sealant ring located on the

bottom of the ANGLED SEAT

ADAPTER. Do not remove

SEALANT RING.

Step 11: Check for flat

surface on seat. Any

damage to seat will

require replacement of

the entire brass seat with

Fluidmaster’s 507 Flush

Valve.

Step 8: Locate yellow

arrow on the back of the

ANGLED SEAT ADAPTER.

Step 9: Align yellow

arrow on ANGLED SEAT

ADAPTER directly toward

the plastic OVERFLOW

PIPE.

Step 10: Firmly press the

ANGLED SEAT ADAPTER

onto the flush valve seat

as shown above.

Proceed to Section 4.

Step 13: Slide the BRASS

SEAT ADAPTER down the pipe

and snap it to the FLUSH

VALVE SEAT as shown.

Proceed to Section 4.

SEATED

ANGLED FLUSH

VALVE SEAT

OVERFLOW

PIPE

REMOVE PAPER

SECTION 3: INSTALLING THE BRASS SEAT ADAPTER

ALIGNMENT

ARROW

ALIGNMENT

ARROW

SEATED

SEAT

SURFACE

MUST BE

FLAT

PROCEED TO INSIDE PAGES

FOR NEXT STEPS

SEALANT

RING

WARNING

DO NOT USE IN-TANK DROP-IN TOILET BOWL CLEANERS

CONTAINING BLEACH OR CHLORINE. Use of such products

will: (1) RESULT IN DAMAGE to tank components and MAY

CAUSE FLOODING and PROPERTY DAMAGE and (2) VOID

FLUIDMASTER WARRANTY. DO NOT overtighten nuts or

tank/ bowl may crack.

Summary of content (4 pages)

PAGE 1
Dual Action Handle (Handle) E The DUAL ACTION HANDLE will allow you to flush UP for a half flush and DOWN for a full flush. Visit www.duoflush.com for easy-to-follow installation videos and additional troubleshooting tips. The PerforMAX Fill Valve maximizes system performance. It replaces the fill valve currently in your tank.
PAGE 2
SECTION 4: INSTALLING THE DUO FLUSH VALVE TM ALIGN TO OPENING FLUSH CABLE SEE NOTE BELOW FLUSH CABLE ALIGNMENT ARROW Step 14: Remove foam around ADJUSTMENT DIALS. Step 15: Locate white arrow on SNAP-ON MOUNT and align it facing the OVERFLOW PIPE. Do not install yet. CLIP TO OVERFLOW PIPE SNAP-ON MOUNT TANK LEVER HOLE FLUSH CABLE Note: Make sure not to sharply bend or kink the FLUSH CABLE. SNAP-ON MOUNT FLUSH CABLE OVERFLOW HOSE FLUSH VALVE SEAT Step 18: Press DUO FLUSH onto seat.
PAGE 3
SECTION 9: RECONNECTING THE WATER SUPPLY: CONNECTION TYPES METAL FLANGED TUBING METAL SPIRAL TUBING LOCK NUT Warning Plastic nut. HAND TIGHTEN ONLY. DO NOT over-tighten. DO NOT use plumber’s putty to seal fittings (The use of Teflon tape is optional). DO NOT use thread lubricants. Use of thread sealants or lubricants can damage plastic nut and result in flooding and property damage.
PAGE 4
DUO FLUSH TROUBLESHOOTING TM 1. Tank Lid Interference on Half (Upward) Flush 2. Seal Leaking 3. Water Level in Bowl is Low Problem: Tank lever hits tank lid forcing the user to hold the handle Problem: The tank continues to leak water causing water loss in the tank. Problem: Toilet bowl water level is not filling up high enough even after adjusting both adjustment dials on DUO FLUSHTM. .