QUICK Install Guide K-400A-023 400A FILL VALVE MANSFIELD® REPAIR KIT VIDEO HOW-TO VIDEO VISIT: FLUIDMASTER.COM *See back page for important legal information.
GETTING STARTED STEP 1: PREPARE TANK TOOLS NEEDED PARTS OVERVIEW Tank Water Level Adjustment Screw Bucket Sponge Towel Scissors A: TURN OFF WATER TURN (Optional) CLOCKWISE Refill Tube Flush Valve Seal B: DRAIN WATER Flush toilet to drain most of the water from the tank.
STEP 2: REMOVE OLD FILL VALVE A: REMOVE CONNECTOR Remove water supply connector from bottom of fill valve by twisting connector nut to the left (clockwise). Towel (Optional) STEP 3: REMOVE FLUSH VALVE A: REMOVE STOP CAP (a) FROM FLUSH VALVE Twist left (counterclockwise) to remove. a NOTE: Inspect water supply connector. Replace it if it is worn, or you don’t know how old it is, to prevent flooding and property damage.
STEP 4: INSTALL NEW SEAL A: REPLACE RED SEAL Be sure seal is positioned in the very top groove at bottom of flush valve tower. STEP 5: REMOVE AND REPLACE OLD LEVER A: REMOVE LEVER Unscrew tank lever nut by twisting counterclockwise, remove nut and pull lever from tank. NOTE: May require pliers if stuck. Pliers (Optional) Proceed to Step 4B only if keeping your original lever. If replacing lever, proceed to Step 5A.
STEP 6: ADJUST HEIGHT OF NEW FILL VALVE A: TWIST FILL VALVE TO ADJUST HEIGHT Top of fill valve cap should measure roughly 3" above top of overflow pipe when installed. NOTE: Increasing height allows more water to fill in the tank. STEP 7: INSTALL NEW FILL VALVE A: PUSH REFILL TUBE ONTO FILL VALVE REFILL PORT B: INSERT FILL VALVE Position refill tube to face flush valve making sure fill valve parts do not interfere with lever arm*.
STEP 8: FINISHING STEPS A: ATTACH WATER SUPPLY CONNECTOR TO FILL VALVE Twist to the right (counterclockwise) STEP 9: FINE-TUNE TANK WATER LEVEL A: FLUSH THE TOILET TO CHECK THE TANK WATER LEVEL After the water stops filling the tank, the water level should be roughly ½ inch below the top of overflow pipe to ensure a proper flush. RIGHT *Hand-tighten only. DO NOT OVERTIGHTEN. B: TURN ON WATER Check for leaks.
STEP 10: FLUSH THE TOILET A: FLUSH THE TOILET If you’re satisfied with the flush, YOU’RE DONE! TROUBLESHOOTING IF THE FILL VALVE: • DOES NOT TURN ON • WON’T TURN OFF • WON’T REFILL TANK REMOVE CAP AND CHECK FOR DEBRIS YOU DID IT! We knew you could! Share your success story with friends and family! A: Turn off water supply. B: Flush toilet. C: With right hand push float up, grip and hold shaft under float. D: With left hand twist cap and lever arm counterclockwise to unlock cap.
TROUBLESHOOTING REPLACE FILL VALVE SEAL A: Remove cap (see page 13). B: Replace seal with a *genuine Fluidmaster 242 Seal. C: Replace valve cap. • Place cap assembly on top of gray valve body by aligning cap arm and adjustment rod next to refill tube. • Press down on top cap while rotating top & arm clockwise to locked position. ADDITIONAL QUESTIONS? * Always use genuine Fluidmaster parts when installing or repairing.
GUÍA DE INSTALACIÓN RÁPIDA GUÍA DE INSTALACIÓN RÁPIDA VÁLVULA DE LLENADO 400A PASO 1: PREPARE EL TANQUE A: B: INSTALE CON CONFIANZA *Consulte la última página para obtener información legal importante. VIDEO HERRAMIENTAS NECESARIAS VIDEO DE CÓMO HACERLO Balde, Esponja, Toalla, Tijeras (opcionales) VISITE: FLUIDMASTER.COM PAGINA DE ESPECIFICACIONES DEL PRODUCTO K-400A-023 EMPEZANDO: RESUMEN DE PIEZAS C: PASO 2: REMUEVA LA VÁLVULA DE LLENADO ANTIGUA (IMÁGENES P.
GUÍA DE INSTALACIÓN RÁPIDA PASO 5: REMUEVA Y REEMPLACE LA PALANCA GUÍA DE INSTALACIÓN RÁPIDA (IMÁGENES P.7) A: REMUEVA LA PALANCA VIEJA. Desenrosque la tuerca de la palanca del tanque, girándola al sentido contrario a las manecillas del reloj, remueva la tuerca y saque la palanca del tanque. NOTA: Es posible que requiera un alicate si esta atorada. B: INSTALE LA PALANCA NUEVA. Pase la palanca por el orificio del tanque.
SOLUCIÓN DE PROBLEMAS PASO 10: DESCARGUE EL SANITARIO A: H: • Coloque el ensamble de la tapa sobre el cuerpo gris de la válvula alineando el brazo de la tapa y el tornillo de ajuste al lado de la manguera de relleno. DESCARGUE EL SANITARIO. Si está satisfecho con el descargue, ¡TERMINÓ! • Presione hacia abajo sobre la tapa mientras gira la tapa y el brazo en el sentido de las manecillas del reloj hasta que se asegure.
¿PREGUNTAS ADICIONALES? Para asistencia para la instalación, comuníquese con nuestro departamento de servicio técnico. EMAIL, CHAT o LLAME a nuestro número gratuito. www.fluidmaster.
WARNING DO NOT USE IN-TANK DROP-IN TOILET BOWL CLEANERS CONTAINING BLEACH OR CHLORINE. Use of such products will: (1) RESULT IN DAMAGE to tank components and MAY CAUSE FLOODING and PROPERTY DAMAGE and (2) VOID FLUIDMASTER WARRANTY. Fluidmaster Flush ‘n Sparkle Toilet Bowl Cleaning System is recommended for those choosing to use in-tank bowl cleaners and WILL NOT VOID the FLUIDMASTER WARRANTY because it will not damage the components. DO NOT overtighten nuts or tank/bowl may crack.
