Owners manual

ManualsBrandsFLUKE NETWORKS INC. ManualsComputers & LaptopsPOCKET TONER NX8VV KIT-MAIN TNR 8-ID AD - FLUKE NETWORKS INC. - PTNX8-VV-PRO

PN 3968800 January 2011, Rev. 2 3/12

names are trademarks of their respective companies.

Pocket Toner

, Speed 81™, and Dial Tone Detective™ are

trademarks of Gale Corporation.

NX8 Pocket Toner

Users Guide

The NX8 Pocket Toner lets you quickly do tests

for continuity, short circuits, ac and dc voltage,

and 50

Ω or 75 Ω termination. The standard

adapters let you use the toner on cable with

F-type connectors. Optional adapters let you

use the toner on twisted pair, coaxial, and

two-wire radial cable.

The optional Dial Tone Detective

™

lets you

quickly see if a dial tone is present at a

telephone jack and if the polarity of the wires

is correct.

Safety Information



Warning or Caution: Risk of damage

to or destruction of equipment or

software. See explanations in the

manual.



Warning: Risk of electrical shock.

Summary of content (11 pages)

PAGE 1
NX8 Pocket Toner ® Users Guide The NX8 Pocket Toner lets you quickly do tests for continuity, short circuits, ac and dc voltage, and 50 Ω or 75 Ω termination. The standard adapters let you use the toner on cable with F-type connectors. Optional adapters let you use the toner on twisted pair, coaxial, and two-wire radial cable. The optional Dial Tone Detective™ lets you quickly see if a dial tone is present at a telephone jack and if the polarity of the wires is correct.
PAGE 2
  Do not connect this equipment to public communications networks, such as telephone systems. See the warning below. Do not put products that contain circuit boards into waste containers. Refer to local regulations for disposal procedures. Warning To prevent possible fire, electric shock, or personal injury: • Do not connect the toner to more than 30 Vac, 42 Vpk, or 60 Vdc. • This equipment has no insulation against on-hook, dial tone, ring, or transient voltages.
PAGE 3
Features Test port Speaker Display Power key Adapter Main unit ID cap Adapter Battery cap Speed 81 coupler* Toner cap * F-type coupler that helps you make connections faster.
PAGE 4
Auto Shut-Off The main unit turns off if the condition of the line does not change for 10 minutes. How to Use the Toner 1 For unterminated cable, connect the correct adapter to an ID cap or the toner cap, then connect the cap to the far end of the cable. 2 Connect the correct adapter to the main unit. 3 Turn on the main unit, then connect it to the near end of the cable.
PAGE 5
A blinking dash indicates an open circuit. A blinking "S" indicates a short circuit. A "C" indicates continuity with the toner cap or a 50 Ω or 75 Ω terminator Solid: DC voltage is present (>6 V dc). Blinking: AC voltage is present (>6 V ac). The numbers 1 through 8 indicate continuity with one of the eight ID caps. Notes The toner cap emits a loud, steady tone when it has is continuity with the main unit. If the condition of the line changes, the main unit emits a loud, brief tone.
PAGE 6
RJ11 66-Block RJ45 BNC 2-Wire Clip RCA Push-on F-Type Toner Cap
PAGE 7
How to Detect Dial Tones 1 Connect the optional Dial Tone Detective to a telephone jack. To hear a tone when a dial tone is present, use the Speed 81 coupler to connect the toner cap to the Dial Tone Detective. 2 If there is a dial tone, the green LED is on. If the jack is reverse-wired, the red LED is on. LEDs Maintenance Warning To prevent possible fire, electrical shock, personal injury, or damage to the toner: • Do not open the case, except to replace the battery.
PAGE 8
• If you replace parts that are not specified as replacement parts, the warranty will not apply to the product and you can make the product dangerous to use. • Use only service centers that are approved by Fluke Networks. Cleaning Caution To prevent damage to the display or the case, do not use solvents or abrasive materials. To extend battery life, remove the battery if you will not use the toner for a long period of time.
PAGE 9
Specifications Approximate distance: 300 m (1,000 ft) Output voltage in continuity mode: 3.6 Vdc (with a new battery) Toner frequency: Main unit: 2.7 kHz. Toner cap: 2.3 kHz Maximum input voltage: 30 Vac, 42 Vpk, or 60 Vdc Battery type: 1.5 V AAA alkaline Auto shut-off: 10 minutes Operating temperature: -20 °C to +65 °C Storage temperature: -30 °C to +70 °C Altitude: 3,000 m (10,000 ft) maximum Relative humidity: 5 % to 95 % (noncondensing) Dimensions and weight: 5.4 in x 0.6 in (138 mm x 15 mm), 2.
PAGE 10
Contacting Fluke Networks www.flukenetworks.com support@flukenetworks.com +1-425-446-4519 • Australia: 61 (2) 8850-3333 or 61 (3) 9329 0244 • • • • • • • • • • Beijing: 86 (10) 6512-3435 Brazil: 11 3759 7600 Canada: 1-800-363-5853 Europe: +31-(0) 40 2675 600 Hong Kong: 852 2721-3228 Japan: 03-6714-3117 Korea: 82 2 539-6311 Singapore: 65-6799-5566 Taiwan: (886) 2-227-83199 USA: 1-800-283-5853 For more phone numbers, go to our website.
PAGE 11
LIMITED WARRANTY AND LIMITATION OF LIABILITY Fluke Networks mainframe products will be free from defects in material and workmanship for one year from the date of purchase. Parts, accessories, product repairs and services are warranted for 90 days, unless otherwise stated. Ni-Cad, Ni-MH and Li-Ion batteries, cables or other peripherals are all considered parts or accessories.