Quick Start Guide

ManualsBrandsFluke Networks ManualsEquipmentCertiFiber Pro

PN 4343722 (English) May 2013, Rev. 3 8/2015

2013-2015 Fluke Corporation

All product names are trademarks of their respective companies.

*4343722*

CertiFiber

Pro

Optical Loss Test Set

Getting Started Guide

The CertiFiber Pro Optical Loss Test Set (OLTS) modules attach to

Versiv

™

main and remote units to make rugged, hand-held

testers that let you certify, troubleshoot, and document fiber

optic network cabling.

Accessing the Product Manuals

This guide provides basic information to help you get started

using the tester. For more detailed information, see the latest

versions of the Versiv Users Manual and the Versiv Technical

Reference Handbook provided on the Fluke Networks website.

Safety Information

Warning



To prevent possible fire, electric shock, or personal injury:



Read all safety information before you use the

Product.



Carefully read all instructions.



Do not open the case. You cannot repair or replace

parts in the case.



Do not modify the Product.



Warning or Caution: Risk of damage or destruction to

equipment or software. See explanations in the manuals.



Warning: Risk of fire, electric shock, or personal injury.



Warning: Class 1 or Class 2 lasers. Risk of eye damage

from hazardous radiation.



This key turns the Product on and off.

Summary of content (10 pages)

PAGE 1
CertiFiber ® Pro Optical Loss Test Set Getting Started Guide The CertiFiber Pro Optical Loss Test Set (OLTS) modules attach to Versiv™ main and remote units to make rugged, hand-held testers that let you certify, troubleshoot, and document fiber optic network cabling. Accessing the Product Manuals This guide provides basic information to help you get started using the tester.
PAGE 2
                Use only replacement parts that are approved by Fluke Networks. Do not touch voltages > 30 V AC rms, 42 V AC peak, or 60 V DC. Do not use the Product around explosive gas, vapor, or in damp or wet environments. Use this Product indoors only. Use the Product only as specified, or the protection supplied by the Product can be compromised. Do not use and disable the Product if it is damaged. Do not use the Product if it operates incorrectly.
PAGE 3
 Use the Product only as specified or hazardous laser radiation exposure can occur. Caution To prevent damage to the Product or cables under test and to prevent data loss, read all safety information given in all documentation supplied with the Product. Connectors, Keys, and LEDs B  C D E F B  C D E F A O N M L K J G H I P G K J Figure 1. Connectors, Keys, and LEDs I HGP00.EPS  LCD display with touchscreen.  Singlemode output port with removable connector adapter and dust cap.
PAGE 4
 Micro-AB USB port: This USB port lets you connect the tester to a PC so you can upload test results to the PC (main tester only) and install software updates in the tester.  Type A USB port: This USB host port lets you save test results on a USB flash drive, connect the FI-1000 video probe to the tester, or connect a Wi-Fi adapter for access to Fluke Networks cloud services..  Headset jack.  : Starts a test. To start a test, you can also tap TEST on the display.  Power key.
PAGE 5
 Fiber Type: Select a fiber type that is correct for the type you will test.  Test Limit: Select General Fiber Optic.  Reference Method: Select 1 Jumper Reference.  No. of Connectors/Splices: These settings are only for test limits that use a calculated limit for loss. They are not applicable to the General Fiber Optic limit. 2-4 To save the settings, tap SAVE on the TEST SETUP screen. A B C D E HGP01.EPS  To set up a project, tap the PROJECT panel.
PAGE 6
3. Clean and Inspect All Connectors Caution Use proper cleaning procedures to clean all fiber connectors before every use. Neglecting this step or using improper procedures can cause unreliable test results and may permanently damage the connectors. See the Users Manual for instructions. 4. Set the Reference and Verify Your Test Reference Cords The reference procedure for fiber cable sets a baseline power level for loss measurements. It is important to set the reference frequently.
PAGE 7
Caution Do not disconnect the outputs ( and ) after you set the reference. When you use the EF-TRCs, DO NOT use other mandrels. Test reference cord Fiber link Test reference cord Reference TRC Verification Fiber Link Test * Use the EF-TRCs only with multimode modules. GPU122.EPS Figure 3. Connections for Smart Remote Mode (1 Jumper Reference, Multimode Fiber) 6. Examine the Results The tester shows a summary of the test results for the fibers (Figure 4, left).
PAGE 8
Figure 4. Examples of Fiber Test Results Screens 7. HGP02.EPS Save the Results  If Auto Save is on, the tester uses the next two IDs to save the results for the two fibers.  If Auto Save is off, tap SAVE if the test passed or FIX LATER if the test failed. The SAVE RESULT screen shows the next two IDs available. You can change the IDs if necessary. The tester saves the results in the DEFAULT project, unless you selected a different project.
PAGE 9
Registration Registering your product with Fluke Networks gives you access to valuable information on product updates, troubleshooting tips, and other support services. To register, use LinkWare PC software. Download LinkWare PC from the Fluke Networks website Contact Fluke Networks www.flukenetworks.com support@flukenetworks.com 1-800-283-5853, +1-425-446-5500 Fluke Networks operates in more than 50 countries worldwide. For more contact information, go to our website.
PAGE 10
LIMITED WARRANTY AND LIMITATION OF LIABILITY Fluke Networks mainframe products will be free from defects in material and workmanship for one year from the date of purchase, unless stated otherwise herein. Parts, accessories, product repairs and services are warranted for 90 days, unless otherwise stated. Ni-Cad, Ni-MH and Li-Ion batteries, cables or other peripherals are all considered parts or accessories.