Datasheet

ManualsBrandsFluke Networks ManualsData & CommunicationsFiber QuickMap Multimode Fiber Distance and Fault Tester

Fiber OneShot™ PRO and Fiber

QuickMap™ measure length and identify

high loss events on single mode (Fiber

OneShot PRO) and Multimode (Fiber

QuickMap) fiber optic cable. Like an OTDR,

a laser sends light pulses through the fiber

and measures the power and timing of light

reflected from high loss connections and

splices, and the end of the fiber.

They are very simple to use:

1. Turn on the unit.

2. Connect your fiber to the SC connector on

the unit (optional adapters for LC, FC and

ST, are available) – remember to clean

connector end faces first

3. Press ‘Test’.

4. In about 5-6 seconds the unit displays

loss and distance of the first incident

detected. Additional incidents can be seen

by pressing the up or down buttons. The

unit automatically checks to make sure the

fiber is not active before allowing the test

to begin.

Locate Faults beyond the range of a Visual Fault Locator (VFL)

VFLs work well for exposed lengths of fiber near a patch panel by illuminating bad connections

and breaks. They are not very helpful for cable runs more than a few meters, or when the

cable is not visible or accessible, or when the laser light can’t penetrate the jacket.

Optical Time Domain Reflectometers (OTDR) provide graphical data and analysis along the

entire length of a cable, way beyond the reach of a VFL, but they can be expensive and

require more time and skill to operate.

Fiber OneShot PRO and Fiber QuickMap fill the gap between a VFL and an OTDR. These

models have the simplicity of a VFL, and provide distance and power information on high

losses, breaks, and the end of the fiber. They also identify live fiber.

Feature

Typical

VFL

Fiber OneShot PRO

Fiber QuickMap

Typical

OTDR

Illuminates high loss areas ✓

One button operation ✓ ✓

Long range ✓ ✓

Live fiber detection ✓ ✓

Numeric distance display ✓ ✓

Numeric refelctive loss (dB) display ✓ ✓

Graphic display of traces ✓

Trace analysis ✓

Power Meter Options ✓

Data Storage ✓

Data Transfer to PC or Cloud ✓

Cost Low Low-medium High

Datasheet: Fiber OneShot™ PRO Singlemode Fiber Distance and Fault

Locator; Fiber QuickMap™ Multimode Fiber Distance and Fault Locator

Datasheet: Fiber OneShot™ PRO Singlemode Fiber Distance and Fault Locator; Fiber QuickMap™ Multimode Fiber Distance and Fault

Locator

User-selectable loss

and reflectance

thresholds exceeded

Distance to incident

being displayed; in this

case the 4th of 4

Scroll through all

incidents

Loss measurement

1 of 8

Summary of content (8 pages)

PAGE 1
Datasheet: Fiber OneShot™ PRO Singlemode Fiber Distance and Fault Locator; Fiber QuickMap™ Multimode Fiber Distance and Fault Locator Datasheet: Fiber OneShot™ PRO Singlemode Fiber Distance and Fault Locator; Fiber QuickMap™ Multimode Fiber Distance and Fault Locator Fiber OneShot™ PRO and Fiber QuickMap™ measure length and identify high loss events on single mode (Fiber OneShot PRO) and Multimode (Fiber QuickMap) fiber optic cable.
PAGE 2
Applications: Measure and locate high-loss splices Measure and locate high loss connections and breaks Locate the end of a fiber Find potential sources of high bit error rates caused by reflectance from dirty or poor connections Detects live optical signals before it begins testing Feature Fiber OneShot PRO Fiber QuickMap Fiber type Singlemode Multimode Fiber size 9/125µm 50/125µm and 62.5/125µm 1550nm.
PAGE 3
When and Where to Use Fiber OneShot PRO and Fiber QuickMap Fiber OneShot PRO provides immediate and in-depth visibility into a singlemode fiber cable (below). Fiber QuickMap operates the same, except on multimode fiber up to 1,500 meters / 4,921 feet. The result loss of the fiber (RL) is 2.6dB. The receive fiber adds 130m to the length measurment. The end of the link. The length of the link (without the launch fiber) is 8463m.
PAGE 4
Specifications for Fiber OneShot™ PRO Output wavelength 1550nm ± 20nm at 25˚C Fiber Types Tested 9/125µm, Single mode Maximum distance 75,459 feet or 23,000 meters Detection of reflective incidents1a -45dB default threshold (user-selectable: -24dB to -62dB in 1dB increments) Maximum reflectance measurement -24dB Live fiber detection Detects optical signals from 1250nm to 1625nm and shows ACTIVE LINE if a signal is there. Looks for a signal every 3 seconds after the first detection.
PAGE 5
Specifications common to both Dimensions 17.5cm H, 7.8cm W, 3.8cm D, .
PAGE 6
Fiber OneShot™ PRO Ordering Information Model Description Fiber OneShot™ PRO. Includes single mode fiber fault locator unit, screw on interchangeable SC adapter, 4- FOS-S language Quick Reference Guide (manuals in 9 languages available on-line), safety instruction manual, and batteries. Fiber OneShot™ PRO-Kit.
PAGE 7
Accessories for Multimode Fiber QuickMap™ Model Description MRC-50-SCSC Multimode test reference cord (2m) for testing 50μm SC terminated fibers (SC/SC) MRC-50-LCLC Multimode test reference cord (2m) for testing 50μm LC terminated fibers (LC/LC) MRC-50-FCFC Multimode test reference cord (2m)for testing 50μm FC terminated fibers (FC/FC) MRC-50-STST Multimode test reference cord (2m) for testing 50μm ST terminated fibers (ST/ST) MRC-625-SCSC Multimode test reference cord (2m) for testing 62.
PAGE 8
Accessories for Fiber OneShot PRO™ and Fiber QuickMap™ Model Description NFC-Kit-Box Fiber Optic Cleaning Kit PA-SC Screw on SC adapter (not for older meters with rectangular style) PA-LC Screw on LC adapter (not for older meters with rectangular style) PA-FC Screw on FC adapter (not for older meters with rectangular style) PA-ST Screw on ST adapter (not for older meters with rectangular style) Fluke Networks operates in more than 50 countries worldwide.