User manual

ManualsBrandsFLUKE ManualsTest Equipment707 Calibrator Amperage 1 x 9 V PP3 battery (included) Calibrated to Manufacturer's standards (no certificate)

English Instruction SheetPanel 1

707

Loop Calibrator

Instruction Sheet

Introduction

The Fluke 707 Loop Calibrator (hereafter, the Calibrator) is a

compact sourcing and measuring tool. The Calibrator tests current

loops of 0-20 mA or 4-20 mA and measures dc voltage to 28 V. It

comes with a set of alligator-clip test leads, a 9 V alkaline battery,

and this Instruction Sheet.

The Calibrator is a IEC 61010, CAT I 30 V, Pollution Degree 2

instrument. A CAT I instrument is designed to protect against

transients from high-voltage, low-energy sources, like electronic

circuits or a copy machine, for example.

Calibrator Capabilities

Function Range Resolution

Measure V dc

28 V 1 mV

Measure mA dc

Source mA dc

0 to 24 mA 1 μA

Source loop power

24 V dc N/A

Battery Saver

The Calibrator automatically turns off after 30 minutes of inactivity.

To reduce this time or disable this feature:

1. With the Calibrator OFF, press D.

PSXX is displayed, where XX is the turn-off time in minutes.

OFF means the power saver is disabled.

2. Turn m to decrease or increase the turn-off time.

To disable, turn m until the display shows OFF.

3. The Calibrator resumes normal operation after 2 seconds.

August 2001 (English) Rev. 2, 2/08

Summary of content (16 pages)

PAGE 1
English Instruction SheetPanel 1 ® 707 Loop Calibrator Instruction Sheet Introduction The Fluke 707 Loop Calibrator (hereafter, the Calibrator) is a compact sourcing and measuring tool. The Calibrator tests current loops of 0-20 mA or 4-20 mA and measures dc voltage to 28 V. It comes with a set of alligator-clip test leads, a 9 V alkaline battery, and this Instruction Sheet. The Calibrator is a IEC 61010, CAT I 30 V, Pollution Degree 2 instrument.
PAGE 2
English Instruction SheetPanel 2 W Warnings and Cautions To avoid electric shock, injury, or damage to the Calibrator: • Use the Calibrator only as described in this Instruction Sheet or the protection provided by the Calibrator may be impaired. • Do not use the Calibrator around explosive gas, vapor, or dust. • Inspect the Calibrator before use. Do not use it if appears damaged. • Check the test leads for continuity, damaged insulation, or exposed metal. Replace damaged test leads.
PAGE 3
English Instruction SheetPanel 3 Pushbutton Functions Pushbutton D A+D (Power-on Option) Function ON or OFF button. Press A and D simultaneously to toggle between the mA output spans. • 4 mA to 20 mA = 0 % - 100 % (default) • 0 mA to 20 mA = 0 % - 100 % (optional) The selection is saved until it is changed. l+ D (Power-on Option) A l Press + D simultaneously to turn HART resistor (Hr) on. Default is off.
PAGE 4
English Instruction SheetPanel 4 Using the mA Sourcing (Output) Modes The Calibrator outputs current for calibrating and testing 0 to 20 mA and 4 to 20 mA current loops and instruments. In SOURCE mode, the Calibrator supplies the current. In SIMULATE mode, the Calibrator simulates a 2-wire transmitter in an externally-powered current loop.
PAGE 5
English Instruction SheetPanel 5 Contacting Fluke To contact Fluke for product information, operating assistance, service, or to get the location of the nearest Fluke distributor or service center, call: 1-888-44-FLUKE (1-888-443-5853) in U.S.A 1-800-36-FLUKE in Canada +31-402-675-200 in Europe +81-3-3434-0181 Japan +65-738-5655 Singapore +1-425-446-5500 from other countries Or visit Fluke's web site at: www.fluke.com. Register your Calibrator at: http://register.fluke.com.
PAGE 6
English Instruction SheetPanel 6 Simulating a Transmitter When simulating the operation of a transmitter, the Calibrator regulates the loop current to a known value selected by you. A 12 V to 28 V loop supply must be available. Insert the test leads as shown below. 707 LOOP CALIBRATOR Press until SIMULATE mA is displayed. Turn to step up/down 0.1 A. Press in and rotate to step up/down in 100 A increments. Press to step current up or down 25 % of full scale. CAT 30V COM 30 V dc max.
PAGE 7
English Instruction SheetPanel 7 Auto Ramping the mA Output Auto ramping allows you to continuously apply a varying current from the Calibrator to a passive (sourcing) or active (simulate) loop. Your hands remain free to test the transmitter’s response. Press B + C simultaneously to enter the Auto Ramp mode and step to a ramp type.
PAGE 8
English Instruction SheetPanel 8 Measuring dc mA W Caution To prevent damage to the unit under test, ensure that the Calibrator is in the correct mode before connecting the test leads. To measure dc mA: 1. Press A to step to MEASURE mode. MEASURE mA is displayed. 2. Touch test lead probes to the circuit across the load or power source as shown below. 707 LOOP CALIBRATOR Press until MEASURE mA is displayed. CAT 30V COM + 30 V dc max. ADA03F.
PAGE 9
English Instruction SheetPanel 9 Measuring dc mA with Loop Power W Caution To prevent damage to the unit under test, ensure that the Calibrator is in the correct mode before connecting the test leads. Loop power provides +24 V to power a transmitter and to read loop current simultaneously. To measure dc mA with Loop Power: 1. Press A to step to Loop Power mode. MEASURE mA and Loop Power are displayed. 2. Touch test lead probes to the circuit across the load or power source as shown below.
PAGE 10
English Instruction SheetPanel 10 Measuring dc Volts W Caution To prevent damage to the unit under test, ensure that the Calibrator is in the correct mode before connecting the test leads. To measure dc Volts: 1. Press A to step to MEASURE mode. MEASURE V is displayed. 2. Touch test lead probes across the load or power source. 707 LOOP CALIBRATOR Press until MEASURE V dc is displayed. CAT 30V COM + 30 V dc max. ADA01F.
PAGE 11
English Instruction SheetPanel 11 Maintenance W Warning To avoid electric shock, personal injury, or damage to the Calibrator: • Do not service this product other than as described in this Instruction Sheet unless you are a qualified technician and have the required equipment and service information. • Remove any input signals prior to removing test leads and opening case. • When servicing the Calibrator, use only specified replacement parts. • Do not allow water to get in the case.
PAGE 12
English Instruction SheetPanel 12 In Case of Difficulty • Make sure you are using the Calibrator as described in this Instruction Sheet. • Check the battery and test leads. Replace as needed. Contact a Fluke Service Center if the Calibrator needs repair or does not seem to be operating properly. If the Calibrator is under warranty, refer to the warranty statement for warranty terms, conditions, and product return information.
PAGE 13
English Instruction SheetPanel 13 Replacing the Battery W Warning To avoid false readings, which could lead to electric shock or injury, replace the battery as soon as M (low battery indicator) appears on the display. Use only a single 9 V battery, properly installed, to power the Calibrator. The Calibrator uses a single 9 V, alkaline battery (ANSI/NEDA 1604A or IEC 6LR61). To replace the battery: 1. Press D to turn the Calibrator OFF. 2. Remove the test leads from the terminals. 3.
PAGE 14
English Instruction SheetPanel 14 Replaceable Parts . . . 1 2 3 4 5 9 6 7 8 10 12 11 ADA10F.EPS Item Description Part No. Qty. 1. Rotary knob 1618022 1 2. Case top 1618355 1 3. Keypad 1612222 1 4. Case bottom 1618005 1 5. Non-skid foot 885884 1 6. Battery. 9 V, Alkaline, ANSI / NEDA 1604A or IEC 6LR61 614487 1 7. Case screws 665098 4 8. Battery door 665106 1 9. CD ROM 2088974 1 10. Test lead set TL75 1 11. Alligator clips AC72 1 12.
PAGE 15
English Instruction SheetPanel 15 Accuracy Specifications Accuracy is specified for 1 year after calibration at operating temperatures of 18 °C to +28 °C and is given as: ±( [ % of reading ]+[ counts ] ) MEASURE V dc Range: +28 V (+30 V max) Resolution: 1 mV Input Impedance: 1 MΩ Accuracy: ±(0.015 % of reading+2 counts) MEASURE mA dc Range: 20 mA (24 mA max) Resolution: 1 μA Accuracy: ±(0.015 % of reading+2 counts) SOURCE / SIMULATE mA dc Range: 0 mA to 20 mA (24 mA max) Resolution: 1 μA Accuracy: ±(0.
PAGE 16
English Instruction SheetPanel 16 General Specifications Maximum voltage between any terminal and earth ground or between any two terminals: 30 V Storage temperature: -40 °C to 60 °C Operating temperature: -10 °C to 55 °C Operating altitude: 3000 meters maximum Temperature coefficient: ±0.