User manual

ManualsBrandsFLUKE ManualsTest & Measurement Accessoriesi3000s flex-36Clip-on ammeter adapter 915 mm

i3000s/i2000 Flex

AC Current Probe

Instruction Sheet

Introduction

The i3000s 24 Flex, i3000s 36 Flex, and i2000 Flex AC Current

Probes (hereafter referred to as “the Probe”) are used with

oscilloscopes, digital multimeters, recorders or data loggers. The

i3000s probes can be used to measure AC current up to 3000 A.

The i2000 can be used to measure AC current up to 2000 A. The

flexible measuring head allows current measurements on

conductors that are hard to reach or inaccessible using typical

clamp-on current probes.

The Probes provide a low-voltage (3 V AC for i3000s models,

and 2 V AC for i2000) output that is proportional to the current

being measured. The Probes provide full-scale direct readings for

30 A, 300 A, and 3000 A when using the i3000s models, and 20

A, 200 A, and 2000 A when using the i2000.

Symbols

The following table shows the symbols used on the product

and/or in this manual.

Symbol Description

Do not dispose of this product as unsorted municipal

waste. Contact Fluke or a qualified recycler for

disposal.

Important Information. Refer to the manual.

Double/Reinforced insulation.

Do not apply around or remove from the HAZARDOUS

LIVE conductors.

Complies with the relevant European standards.

Conforms to Underwriters’ Laboratory, Inc.

PN 2560447

March 2006

Summary of content (10 pages)

PAGE 1
® i3000s/i2000 Flex AC Current Probe Instruction Sheet Introduction The i3000s 24 Flex, i3000s 36 Flex, and i2000 Flex AC Current Probes (hereafter referred to as “the Probe”) are used with oscilloscopes, digital multimeters, recorders or data loggers. The i3000s probes can be used to measure AC current up to 3000 A. The i2000 can be used to measure AC current up to 2000 A.
PAGE 2
i3000/i2000 English Instruction Sheet Page 2 Safety Instructions In this instruction sheet, a Warning identifies conditions and actions that pose hazard(s) to the user. A Caution identifies conditions and actions that may damage the calibrator or the test instruments. WX Warning To avoid electric shock or personal injury: • Use the Probes only if qualified. • Use caution during installation and use of the Probe; high voltages and currents may be present in circuit under test.
PAGE 3
i3000/i2000 English Instruction Sheet Page 3 • Adhere to local and national safety codes. Individual protective equipment must be used to prevent shock and arc blast injury where hazardous live conductors are exposed. • CAT III equipment is designed to protect against the transients in the equipment in fixed equipment installations, such as distribution panels, feeders and short branch circuits, and the lighting systems in large buildings.
PAGE 4
i3000/i2000 English Instruction Sheet Page 4 Gain variation ±0.08 %/°C Operating temperature i3000s (24 and 36 Flex) -20 to +85 °C (-4 to 185 °F) i2000 Flex 0 to 70 °C (32 to 158 °F) Storage temperature i3000s (24 and 36 Flex) -20 to +85 °C (-4 to 185 °F) i2000 Flex 0 to 70 °C (32 to 158 °F) Temperature coefficient: ± 0.
PAGE 5
i3000/i2000 English Instruction Sheet Page 5 Measuring Head Characteristics Cable length i2000, i3000s 24 Flex i3000s 36 Flex 610 mm (24 in), double insulated 915 mm (36 in), double insulated Cable diameter 14.3 mm (0.562 in) Bend radius 38.1 mm (1.5 in) Output cable 2 m long (78.7 in) Coupling diameter 22.2 mm (0.
PAGE 6
i3000/i2000 English Instruction Sheet Page 6 Operating Instructions Ieb0001.
PAGE 7
i3000/i2000 English Instruction Sheet Page 7 Battery Installation XWWarning To avoid electric shock or personal injury: • Never replace batteries with the flexible measuring head installed on the conductor to be tested or with the output connected to a display device. • Never operate the unit without the battery cover installed. The Probes require two AA/MN1500/LR6 alkaline batteries for operation. The battery compartment is accessed from the rear end of the electronic enclosure.
PAGE 8
i3000/i2000 English Instruction Sheet Page 8 Measuring Current XWWarning • To avoid electric shock or injury, read Safety Instructions before operating this product • Ensure that the conductor to be tested is deenergized To measure current: 1. Connect the output of the electronics to the input of an oscilloscope or other data recording device. XWWarning To avoid electric shock or injury, the flexible current probe is not for use on conductors with a potential of over 600 V. 2.
PAGE 9
i3000/i2000 English Instruction Sheet Page 9 Operation To activate the unit, move the switch from ‘Off’ position to the required measuring range. If the value of current being measured is unknown, select the 3000 A (i3000s models) or 2000 A (i2000) current range and then reduce accordingly. Battery Status Battery status is indicated by an LED on the front of the probe. This LED will flash one time when the unit is activated. The length of time the LED is lit will increase as battery life decreases.
PAGE 10
i3000/i2000 English Instruction Sheet Page 10 LIMITED WARRANTY AND LIMITATION OF LIABILITY This Fluke product will be free from defects in material and workmanship for one year from the date of purchase. This warranty does not cover fuses, disposable batteries, or damage from accident, neglect, misuse, alteration, contamination, or abnormal conditions of operation or handling. Resellers are not authorized to extend any other warranty on Fluke’s behalf.