® 116 True-rms Multimeters Mode d'emploi PN 2538688 July 2006, Rev. 1, 2/07 (French) © 2006, 2007 Fluke Corporation. All rights reserved. Printed in China. All product names are trademarks of their respective companies.
LIMITES DE GARANTIE ET DE RESPONSABILITE La société Fluke garantit l’absence de vices de matériaux et de fabrication de ses produits pendant une période de trois ans prenant effet à la date d’achat. Cette garantie ne couvre pas les fusibles, les piles jetables ou les dommages découlant d’un accident, de négligence, de mauvaise utilisation, d’altération, de contamination ou de conditions anormales de fonctionnement ou de manipulation.
True-rms Multimeter Introduction Le multimètre Fluke 116 est un appareil de mesure efficace vraie (TRMS) à pile (appelés ci-après « multimètre ») qui dispose d’un affichage incrémental de 6000 comptes. Ces multimètres sont conformes aux normes CEI 61010-1 CAT III 2e édition. La norme de sécurité CEI e 61010-1 2 édition définit quatre catégories de mesure (CAT I à IV) en fonction de la gravité du danger des impulsions transitoires.
116 Mode d’emploi Informations sur la sécurité Un message « XWAvertissement » identifie les situations et les pratiques susceptibles de provoquer des blessures, voire la mort. Une mise en garde « WAttention » indique des situations et des actions qui risqueraient d’endommager l’appareil ou l’équipement testé.
True-rms Multimeter Informations sur la sécurité • • • • • • • • B F X J ~ Utiliser uniquement les cordons de mesure de tension, catégorie et intensité identiques à celles du multimètre et approuvées par une agence de sécurité. Retirer les cordons de mesure du multimètre avant d’ouvrir son boîtier ou le compartiment de la pile. Respecter les normes de sécurité locales et nationales en intervenant dans des sites dangereux.
116 Mode d’emploi Afficheur 6 5 7 4 3 8 9 2 1 10 14 13 15 12 11 16 eeo02f.eps 4 Nº A B C D Symbole s R O E K Y Signification Le multimètre est réglé sur la fonction de continuité. Le multimètre est réglé sur le contrôle de diode. L’entrée est une valeur négative. X Tension dangereuse. Tension d’entrée mesurée ≥ 30 V ou condition de surtension (OL). Maintien d’affichage activé. Le résultat affiché sur l’écran est figé.
True-rms Multimeter Afficheur Nº F G H I J K L M N O P Symbole M VWX LoZ nµ°F°C mVµA MkΩ kHz DC, AC N 610000 mV (Affichage incrémental) Auto Volts Auto Manual + 0L 0PEn Signification Mode MIN MAX AVG activé. La valeur maximum, minimum, moyenne ou actuelle est affichée. Le multimètre mesure la tension ou la capacité avec une faible impédance d’entrée. Unités de mesure. Courant continu ou courant alternatif Indicateur de pile faible. Indique la gamme sélectionnée sur le multimètre. Affichage analogique.
116 Mode d’emploi Bornes COM + 2 1 eeo01f.eps Nº A B Description Borne commune (de retour) utilisée pour toutes les mesures. Borne d’entrée pour mesurer la tension, la continuité, la résistance, la capacité, la fréquence, la température, les microampères et le contrôle des diodes. bAtt CAL Err EEPr Err F11Err 6 Messages d’erreur La pile doit être remplacée avant d’utiliser le multimètre. Etalonnage nécessaire. L’étalonnage du multimètre est nécessaire avant d’utiliser le multimètre. Erreur interne.
True-rms Multimeter Positions du commutateur rotatif Positions du commutateur rotatif Position du commutateur x e Hz (bouton) D l Ω s y R S $ Fonction de mesure Sélectionne automatiquement les volts c.a. ou c.c. selon l’entrée détectée avec une faible impédance d’entrée. Tension c.a. de 0.06 à 600 V. Fréquence de 5 Hz à 50 kHz. Tension c.c. de 0,001 V à 600 V. Tension c.a. de 6.0 mV à 600 mV, couplage en courant continu. Tension c.c. de 0,1 à 600 mV. Résistance de 0,1 Ω à 40 MΩ.
116 Mode d’emploi Economiseur de pile (« mode de veille ») Le multimètre passe automatiquement en « mode de veille » et l’affichage s’efface si aucune fonction, changement de gamme ou bouton n’est utilisé pendant 20 minutes. La pression d’un bouton ou la rotation du commutateur rotatif réactive le multimètre. Pour désactiver le mode de veille, maintenez le bouton g enfoncé tout en mettant le multimètre sous tension. Le mode de veille est toujours désactivé dans le mode MIN MAX AVG.
True-rms Multimeter Options au démarrage • En mode de gamme manuelle, l’opérateur sélectionne lui-même la gamme, prioritaire à la gamme automatique. Le multimètre choisit par défaut le mode de gamme automatique à la mise sous tension et Auto apparaît. 1. Pour passer en mode de gamme manuelle, appuyez sur q. Manual apparaît. 2. En mode de gamme manuelle, appuyez sur q pour augmenter de gamme. Une fois la gamme la plus élevée atteinte, le multimètre revient à la gamme la plus faible.
116 Mode d’emploi Mesures de résistance Contrôles de continuité eeo04f.eps XWAvertissement Pour éviter les chocs électriques, les blessures et l’endommagement du multimètre, débrancher l’alimentation du circuit et décharger tous les condensateurs à tension élevée avant de contrôler la résistance, la continuité, les diodes ou la capacité. 10 eeo06f.eps Remarque La fonction de continuité offre une méthode pratique et rapide pour détecter les coupures et les courts-circuits.
True-rms Multimeter Mesures de base Mesures de tension alternative et continue Mesures de millivolts c.a. et c.c. eeo18f.eps eeo03f.eps Utilisation de la sélection Auto Volts Quand le commutateur rotatif est positionné sur x, le multimètre sélectionne automatiquement une mesure de tension c.c. ou c.a., selon l’entrée appliquée entre les jacks + et COM.
116 Mode d’emploi Mesure d’un courant alternatif ou continu WAvertissement Pour éviter toute blessure et l’endommagement du multimètre : • • Ne jamais essayer d’effectuer une mesure de courant dans un circuit où le potentiel électrique en circuit ouvert à la terre est > 600 V. Utiliser les bornes, la position du commutateur et la gamme qui conviennent pour les mesures. eeo08f.eps Pour mesurer les circuits de redressement de la flamme : 1. Réglez le commutateur de fonction sur $. 2.
True-rms Multimeter Mesure d’un courant alternatif ou continu Mesures de capacité Mesures de température eep10f.eps eeo05f.eps XW Avertissement Pour éviter le risque de chocs électriques, ne PAS brancher le 80BK à des circuits sous tension.
116 Mode d’emploi Mesures de fréquence XWAvertissement Pour éviter les risques d’électrocution, ne pas tenir compte des fréquences > 1 kHz sur l’affichage incrémental. Si la fréquence du signal mesuré est > 1 kHz, l’affichage incrémental et Z ne sont pas spécifiés. AC Voltage Frequency Le multimètre mesure la fréquence d’un signal en comptant combien de fois le signal passe par un seuil de déclenchement à chaque seconde. Le niveau de déclenchement est de 0 V pour toutes les gammes. 1.
True-rms Multimeter Mesures de capacité à faible impédance Mesures de courant supérieur à 600 μA La fonction de tension et de millivolts du multimètre, utilisée avec une sonde de courant mV/A optionnelle, permet de mesurer les courants qui tombent en dehors des valeurs nominales du multimètre. Assurez-vous que la fonction sélectionnée sur le multimètre, c.a. ou c.c., convient pour la sonde de courant.
116 Mode d’emploi Utilisation de l’affichage incrémental L’affichage incrémental est similaire à l’aiguille sur un multimètre analogique. Il affiche un indicateur de surcharge (>) à droite et un indicateur de polarité (+) à gauche. Entretien L’entretien du multimètre implique le remplacement de la pile et le nettoyage du boîtier.
True-rms Multimeter Nettoyage XWAvertissement Pour éviter les chocs électriques, les blessures et l’endommagement du multimètre, retirer les cordons de mesure du multimètre avant d’ouvrir son boîtier ou le logement de la pile. Pour retirer le couvercle du logement de la pile en vue de la remplacer : 1. Retirez les cordons de mesure de l’appareil. 2. Retirez la vis du couvercle du logement. 3. Soulevez légèrement le couvercle en utilisant l’appui-doigt. 4.
116 Mode d’emploi Caractéristiques générales La précision est assurée pendant 1 an après l’étalonnage, à des températures de fonctionnement de 18 °C à 28 °C et à une humidité relative de 0 % à 90 %. Les caractéristiques étendues sont disponibles à www.Fluke.com. Tension maximum entre une borne et la prise de terre ............................ 600 V Limite de surtension ................................... 6 kV crête selon CEI 61010-1 600V CAT III, degré de pollution 2 Afficheur .............................
True-rms Multimeter Caractéristiques générales Homologation IP (protection contre l’eau et la poussière) ......... IP42 Tableau 1. Caractéristiques de précision Fonction Gamme Résolution Précision ± ([% du résultat] + [comptes]) Millivolts c.c. 600,0 mV 0,1 mV 0,5 % + 2 Volts c.c. 6,000 V 60,00 V 600,0 V 0,001 V 0,01 V 0,1 V 0,5 % + 2 Auto-V LoZ[1] TRMS 600,0 V 0,1 V c.c., 45 à 500 Hz [1] 500 Hz à 1 kHz 2,0 % + 3 4,0 % + 3 45 à 500 Hz 500 Hz à 1 kHz Mllivolts c.a.
116 Mode d’emploi Tableau 1. Caractéristiques de précision (suite) Fonction Gamme Résolution Précision ± ([% du résultat] + [comptes]) bip sonore à < 20 Ω, inactif à > 250 Ω ; détecte les coupures ou courts-circuits de 500 μs ou plus. Continuité 600 Ω 1Ω Ohms 600.0 Ω 6,000 kΩ 60,00 kΩ 600,0 kΩ 6,000 MΩ 40,00 MΩ 0.
True-rms Multimeter Caractéristiques générales Tableau 1. Caractéristiques de précision (suite) Fonction μA c.a. TRMS[1] (45 Hz à 1 Hz) Gamme 600,0 μA Résolution Précision ± ([% du résultat] + [comptes]) 0,1 μA 1,5 % + 3 (2,5 % + 3 > 500 Hz) μA c.c. 600,0 μA 0,1 μA 1,0 % + 2 Hz (entrée V)[3] 99,99 Hz 999,9 Hz 9,999 kHz 50,00 kHz 0,01 Hz 0,1 Hz 0,001 kHz 0,01 kHz 0,1 % + 2 Remarques : [1] Toutes les gammes en courant alternatif sauf Auto-V LoZ sont spécifiées dans la fourchette 1 % à 100 %.
116 Mode d’emploi Tableau 2. Caractéristiques d’entrée Fonction Volts c.a. Volts c.c. Auto-V LoZ Ohms Contrôle de diode 22 Impédance d’entrée (nominale) Taux d’élimination en mode commun (déséquilibré à 1 kΩ) > 5 MΩ < 100 pF > 10 MΩ < 100 pF > 60 dB en c.c., à 50 Hz ou 60 Hz > 100 dB en c.c., à 50 Hz ou 60 Hz ~3 kΩ < 500 pF > 60 dB en c.c., à 50 Hz ou 60 Hz Tension de test en circuit ouvert < 2,7 V c.c. < 2,7 V c.c. Tension maximale Jusqu’à 6,0 MΩ 40 MΩ < 0,7 V c.c. < 0,9 V c.c.