® 116 True-rms Multimeters Käyttöohje PN 2538688 July 2006, Rev. 1, 2/07 (Finnish) © 2006, 2007 Fluke Corporation. All rights reserved. Printed in China. All product names are trademarks of their respective companies.
RAJOITETTU TAKUU JA VASTUUNRAJOITUS Fluke takaa tämän tuotteen valmistusmateriaalit ja työn kahden vuoden ajaksi ostopäivästä lukien. Tämä takuu ei kata sulakkeita, kertakäyttöisiä paristoja tai onnettomuudesta, väärinkäytöstä, laiminlyönnistä, muutoksista, likaantumisesta tai epätavallisista käyttö- tai käsittelyoloista aiheutuneita vahinkoja. Jälleenmyyjillä ei ole oikeutta laajentaa takuuta Fluken puolesta.
True-rms Multimeter Johdanto Fluken malli 116 on paristokäyttöinen todellisen tehollisarvon monitoimimittari, jossa on 6 000 lukeman näyttö ja pylväskaavio. Tämä mittari vastaa standardien CAT III IEC 61010-1 2. julkaisun vaatimuksia. IEC 61010-1 2. julkaisun turvastandardi määrittää neljä mittauskategoriaa (CAT I – IV), jotka perustuvat transienttisysäysten vaaran suuruuteen. CAT III -mittarit on suunniteltu suojaamaan transienteilta jakelutason kiinteissä laiteasennuksissa.
116 Käyttöopas Turvaohjeet XWVaroitus tarkoittaa vaarallista tilannetta ja toimintoa, joka voi aiheuttaa ruumiinvamman tai kuoleman. WVarotoimi tarkoittaa tilaa tai toimintoa, joka voi vahingoittaa mittaria tai testattavaa laitteistoa. Vältä sähköiskut ja henkilövahingot toimimalla seuraavasti: • Käytä mittaria vain tässä ohjekirjassa määritellyllä tavalla tai mittarin antama suoja voi heikentyä. • Mittaria tai testijohtimia ei saa käyttää, jos niissä on vaurioita tai jos mittari ei toimi kunnolla.
True-rms Multimeter Turvaohjeet • • • • • B F X J ~ Käytä paikallisten ja kansallisten turvaviranomaisten määrittämiä asianmukaisia suojavarusteita, kun työskentelet vaarallisilla alueilla. Vältä työskentelyä yksin. Käytä vain määritettyä vaihtosulaketta tai suojaus voi heikentyä. Tarkasta testijohtimien virtapiirin jatkuvuus ennen käyttöä. Älä käytä, jos lukemat ovat korkeita tai epävakaita.
116 Käyttöopas Näyttö 6 5 7 4 3 8 9 2 1 10 14 13 15 12 11 16 eeo02f.eps Nro A B C D E 4 Symboli s R O Y K Tulkinta Mittarin toiminnoksi on asetettu Jatkuvuus. Mittarin toiminnoksi on asetettu Dioditesti. Syöttö on negatiivinen arvo. X Vaarallinen jännite. Mitattu syöttöjännite ≥ 30 V tai jännitteen ylikuormitustila (OL). Näytön pysäytys on käytössä. Näyttö jumiutuu nykyiseen lukemaan.
True-rms Multimeter Näyttö Nro F G H I J K L M N O P Symboli M VWX LoZ nµ°F°C mVµA MkΩ kHz DC AC N 610000 mV (Pylväskaavio) Auto Volts (Autom. jännitteet) Auto (Autom.) Manual (Käsin) + 0L 0PEn Tulkinta MIN MAX AVG -tila on käytössä. Enimmäis-, vähimmäis- normaali- tai nykyinen lukema näkyy näytössä. Mittari mittaa jännitteen tai kapasitanssin alhaisen syötön impedanssilla. Mittausyksiköitä. Tasavirta tai vaihtovirta Pariston alhaisen varauksen varoitus. Osoittaa mittarin asteikon valinnan.
116 Käyttöopas Liittimet COM + 2 1 eeo01f.eps Nro A B Kuvaus Yleinen (paluu)liitin kaikille mittauksille. Syöttöliitin jännitteen, jatkuvuuden, vastuksen, kapasitanssin, taajuuden, lämpötilan, mikroampeerien mittaukseen ja diodien testaamiseen. bAtt CAL Err EEPr Err F11Err 6 Virheilmoitukset Paristo on vaihdettava. Kalibrointi tarvitaan. Mittari on kalibroitava ennen käyttöönottoa. Sisäinen virhe. Mittari on korjattava. Sisäinen virhe. Mittari on korjattava.
True-rms Multimeter Kiertokytkimen asennot Kiertokytkimen asennot Kytkimen asento x e Hz (painike) D l Ω s y R S $ Mittaustoiminto Valitsee automaattisesti vaihtovirran tai tasavirran voltit perustuen tunnistettuun syöttöön alhaisen impedanssin syötöllä. Vaihtovirtajännite 0.06–600 V. Taajuus 5 Hz–50 kHz. Tasavirtajännite 0,001 V–600 V. Vaihtovirtajännite 6.0 –600 mV, tasavirtakytketty. Tasavirtajännite 0,1–600 mV. Vastus 0,1 Ω–40 MΩ. Jatkuvuuden äänimerkki kytkeytyy päälle < 20 Ω ja pois päältä > 250 Ω.
116 Käyttöopas Paristonsäästötoiminto (virransäästötila) Mittari siirtyy automaattisesti virransäästötilaan ja näyttö tyhjenee, jos toimintoa ei ole muutettu, asteikkoa vaihdettu tai painiketta ei ole painettu 20 minuuttiin. Mittari herää, kun painat jotain painiketta tai käännät kiertokytkintä. Voit kytkeä pariston säästötilan pois päältä pitämällä g painike painettuna samalla kun kytket mittarin päälle. Virransäästötila on aina pois käytöstä MIN MAX AVG tilassa. MIN MAX AVG -taltiointitila.
True-rms Multimeter Käynnistysasetukset • Manuaalisessa asteikon valinnan tilassa voit ohittaa automaattisen asteikon valinnan ja valita asteikon itse. Kun kytket virran mittariin, sen oletusasetuksena on automaattinen asteikon valinta. Esiin tulee Auto. 1. Siirry manuaaliseen asteikon valintatilaan painamalla q. Manual tulee näyttöön. 2. Paina manuaalisessa asteikkotilassa q lisätäksesi asteikkovälejä. Korkeimman asteikon jälkeen mittari siirtyy alhaisimpaan asteikkoon.
116 Käyttöopas Jatkuvuuden testaaminen Vastuksen mittaaminen eeo06f.eps XWVaroitus eeo04f.eps Sähköiskun, loukkaantumisen tai mittarin vaurioitumisen välttämiseksi piirin virta ja kaikki korkeajännitteiset kondensaattorit on kytkettävä pois päältä ennen vastuksen, jatkuvuuden, diodien tai kapasitanssin testaamista. 10 Huomautus Jatkuvuustoiminto on nopein ja kätevin menetelmä avointen piirien ja oikosulkujen tarkistukseen.
True-rms Multimeter Perusmittauksien tekeminen Vaihtovirta- ja tasavirtajännitteen mittaaminen Tämä toiminto asettaa myös mittarin syöttöimpedanssin noin 3 kΩ:iin haamujännitteiden aiheuttamien väärien lukemien välttämiseksi. Vaihtovirta- ja tasavirtamillivolttien mittaaminen eey03f.eps Automaattisen jännitteen valinnan käyttö Toimintokytkimen ollessa x asennossa, mittari valitsee automaattisesti tasavirran tai vaihtovirran jännitteen mittauksen perustuen käytettyyn syöttöön liittimien + ja COM välillä.
116 Käyttöopas Vaihtovirran ja tasavirran mittaaminen WVaroitus Henkilövamman tai mittarin vaurioitumisen estämiseksi: • • Älä koskaan yritä tehdä piirin sisäisen virran mittausta, kun avoimen piirin potentiaali maahan on > 600 V. Käytä mittaukseen oikeaa kytkinasentoa ja asteikkoa. eey08f.eps Valokaaren tasasuuntauspiirien mittaaminen: 1. Käännä toimintokytkin asentoon $. 2. Kytke mittari valokaaren tunnistimen anturin ja ohjausmoduulin välille. 3. Kytke lämmitysyksikkö päälle ja tallenna μA-mittaus.
True-rms Multimeter Perusmittauksien tekeminen Lämpötilan mittaaminen Kapasitanssin mittaaminen eey10f.eps XW Varoitus eeo05f.eps Vältä sähköiskut – ÄLÄ kytke 80BK lämpöparia jännitteellisiin piireihin.
116 Käyttöopas Mittari mittaa signaalin taajuuden laskemalla kerrat, jolloin signaali ylittää kynnyksen (laukaisurajan) joka sekunti. Kynnys on 0 V kaikissa asteikoissa. Taajuuden mittaaminen XWVaroitus Sähköiskun välttämiseksi jätä huomioimatta pylväskaavio taajuuksille > 1 kHz. Jos mitatun signaalin taajuus on > 1 kHz, pylväskaavio ja Z jätetään määrittämättä. 1. Ota taajuusmittaus käyttöön ja pois käytöstä painamalla g. Taajuus toimii vain vaihtovirtajännitteellä. 2.
True-rms Multimeter Alhaisen impedanssin kapasitanssimittaukset Yli 600 μA:n virran mittaaminen Diodien testaus Ehjä diodi Mittarin millivolttitoimintoa voidaan käyttää valinnaisella mV/A-ulostulon virta-anturilla mittaamaan virtoja, jotka ylittävät mittarin luokituksen. Varmista, että mittarissa on valittu nykyiselle anturille sopiva toiminto, joko vaihtovirta tai tasavirta. Tarkista yhteensopivat virtapihdit Fluken tuoteluettelosta tai ota yhteyttä paikalliseen Fluken edustajaan.
116 Käyttöopas Pylväskaavion käyttö Pylväskaavio toimii kuten analogiamittarin neula. Siinä on ylikuormituksen osoitin (>) oikealla ja napaisuuden osoitin (+) vasemmalla. Koska pylväskaavio päivittyy paljon nopeammin kuin digitaalinen näyttö, pylväskaavio on hyödyllinen huippu- ja nollasäätöjen tekemisessä. Kunnossapito Mittarin kunnossapitoon kuuluu pariston vaihto ja kotelon puhdistus. Pariston vaihto Pylväsnäyttö poistetaan käytöstä kapasitanssia ja lämpötilaa mitattaessa.
True-rms Multimeter Puhdistus XWVaroitus Sähköiskun, vamman tai mittarin vaurion välttämiseksi poista testijohtimet mittarista ennen kotelon tai paristolokeron kannen avaamista. Irrota paristolokeron kansi pariston vaihtamista varten seuraavasti: 1. Irrota testijohtimet mittarista. 2. Irrota paristolokeron kannen ruuvi. 3. Nosta kantta hieman sormikolon avulla. 4. Irrota kansi kotelosta nostamalla se suoraan ylös.
116 Käyttöopas Yleiset erittelyt Tarkkuus on määritetty 1 vuoden ajaksi kalibroinnin jälkeen, käyttölämpötiloissa 18 °C – 28 °C, suhteellinen kosteus 0 % – 90 %. Laajennetut määritykset ovat saatavilla sivustolta www.Fluke.com. Enimmäisjännite liittimen ja maadoituksen välillä ................................... 600 V Suojaus virtapiikeiltä .................................. 6 kV huippu per IEC 61010-1600V CAT III, Saasteaste 2 Näyttö...........................................................
True-rms Multimeter Yleiset erittelyt IP-luokitus (pölyltä ja vedeltä suojaus)......... IP42 Taulukko 1.
116 Käyttöopas Taulukko 1. Tarkkuusmääritykset (jatkoa) Toiminto Mittausasteikko Erottelukyky Tarkkuus ± ([% lukemasta] + [lukemat]) Äänimerkki päällä < 20 Ω, pois > 250 Ω; tunnistaa avoimet tai oikosulut 500 μs tai pidemmät.
True-rms Multimeter Yleiset erittelyt Taulukko 1. Tarkkuusmääritykset (jatkoa) Toiminto Mittausasteikko Erottelukyky Tarkkuus ± ([% lukemasta] + [lukemat]) AC μAmpeerit True-rms[1] (45 Hz – 1 kHz) 600,0 μA 0,1 μA DC μAmpeerit 600,0 μA 0,1 μA 1,0 % + 2 Hz (V syöttö)[3] 99,99 Hz 999,9 Hz 9,999 kHz 50,00 kHz 0,01 Hz 0,1 Hz 0,001 kHz 0,01 kHz 0,1 % + 2 1,5 % + 3 (2,5 % + 3 > 500 Hz) Huomautukset: [1] Kaikki AC asteikot paitsi Auto-V LoZ määritetään 1 % – 100 % asteikosta.
116 Käyttöopas Taulukko 2.