- FLUKE Fluke 430 Series Three-Phase Power Quality Analyzer User's Manual

ManualsBrandsFluke ManualsMonitor430 Series

Fluke 430 Series

Three-Phase Power

Quality Analyzers

Pinpoint power problems

faster, safer and in greater detail

Technical Data

The Fluke 434 and 433 three-phase power quality

analyzers help you locate, predict, prevent and trou-

bleshoot problems in power distribution systems.

These easy-to-use handhelds are a “must have” for

any person who maintains or troubleshoots three

phase distribution. The new IEC standards for

flicker and power quality are built right in to take

the guess work out of monitoring.

•

Records all your necessary values in a three

phase system.

•

Minimal setup required with intuitive menus.

•

Highest safety rating in the industry.

•

Four voltage and four current channels.

•

Captures waveform data on all phases

simultaneously.

•

System-Monitor: Six power quality parameters

on one dashboard

•

Automatic Transient display: Never miss an event.

•

Auto Trend: Don’t waste time setting up recordings.

•

Rugged, handheld recorder.

•

Seven hours operating time per charge on NiMH battery pack.

•

ransfer data files to your PC for reporting and analysis using

FlukeView

software.

CAT IV 600 V and CAT III 1000 V safety rating

Designed to help protect you and your equipment against

electrical shock and fire, the Fluke 430 Series analy

zers,

accessories and charger are all certified to meet the stringent

safety standards for use in C

T IV 600 V and CAT III 1000 V

environments. They are the first tools of their kind to carry

the C

T I

V rating and therefore can be used at virtually all

power connections and outlets in a low-voltage power

distribution system

Summary of content (8 pages)

PAGE 1
Fluke 430 Series Three-Phase Power Quality Analyzers Pinpoint power problems faster, safer and in greater detail The Fluke 434 and 433 three-phase power quality analyzers help you locate, predict, prevent and troubleshoot problems in power distribution systems. These easy-to-use handhelds are a “must have” for any person who maintains or troubleshoots three phase distribution. The new IEC standards for flicker and power quality are built right in to take the guess work out of monitoring.
PAGE 2
Quickly see the trend Measures everything Auto Trend feature allows fast insight into changes over time. Every displayed reading is automatically and continuously recorded without having to set thresholds or intervals and without manually starting the process. Quickly view trends for voltage, current, frequency, power, harmonics or flicker on all phases and neutral. Analyze the trends using the cursors and zoom tools — even while background recording continues.
PAGE 3
System-Monitor: Multi-parameter power quality health check on one display ‘off line’ on stored measurement data. The stored measurements can also be transferred to a PC with FlukeView ® software. The software’s ‘view’ A single push of the MONITOR button delivers a mode allows cursors and zoom tools to be used single dashboard display of rms voltage, haron stored measurements.
PAGE 4
Specifications Input characteristics Voltage inputs Number of inputs Maximum input voltage Maximum peak voltage Input impedance Bandwidth Scaling Current inputs Number of inputs Type Range Input impedance Bandwidth Scaling Nominal frequency Sampling system Resolution Maximum sampling speed RMS sampling PLL synchronization Display modes Waveform display Phasor Matrix readings AutoTrend graph Bargraph Eventlist Measurement modes Scope Volts/Amps/Hertz Dips and Swells Harmonics DC, 1 to 50 Power and Energ
PAGE 5
Specifications continued Accuracy, resolution and range Volt/Amps/Hertz Measurement range Resolution Vrms (AC+DC) 1 to 1000 Vrms 0.1 Vrms Vpk 1 to 1400 Vpk 1V CFV 1.0 to > 2.8 0.1 0,001 to 10 Arms1 Arms (AC+DC) 0 to 20,000 Arms1 with included clamps 0 to 400 Arms 0.1 and 1 Arms Apk using 1mV/A scaling 0 - 5500 Apk 10 A CFA using 1mV/A scaling 1 to 10 0.1 50 Hz nominal 42.50 to 57.50 Hz 0.01 Hz 60 Hz nominal 51.00 to 69.00 Hz 0.01 Hz Dips and swells Vrms1⁄2 (AC+DC) 0.0 to100 % of nominal voltage 0.
PAGE 6
Specifications continued Trend recording Method AutoTrend automatically records min, max and average values over time for all readings being displayed for the 3 phases and neutral simultaneously Volts/amps/hertz, harmonics, power and energy, flicker and unbalance mode Sampling 5 readings/sec continuous sampling per channel Memory 1800 min, max and avg points for each reading Recording time From 30 min with 1 second display resolution up to 450 days with 6 hour display resolution Zoom Up to 6 x horizontal z
PAGE 7
Specifications continued General Case Design Drip and dust proof Shock and Vibration Display Type Size Resolution Contrast and brightness Memory Screens Data Limit templates Real-time clock Mechanical Size Weight Power Line power Battery power Battery operating time Battery charging time Power saving Standards Measurement methods used Power Quality Flicker Harmonics Safety Compliance Max voltage on banana input Max voltage on current BNC input Environmental Operating temperature Storage temperature Humidity
PAGE 8
Optional 430 Series Accessories • • • • • • • • i400s AC Current Clamp — Replacement current clamp for the Fluke 430 Series: It is compatible with any oscilloscope, ScopeMeter® Test Tool or Power Quality Analyzer that accepts BNC connectors and is capable of millivolt measurements. TLS430 Test Lead Set — Test lead replacement set for the 430 Series Power Quality Analyzer. Set includes five test leads and five alligator clips.