Case Studies
2 Fluke Corporation Tips for learning power quality analysis
Benoit is a 23 year veteran
of medical electronics, but he
was not an expert on power
quality. And without hard
facts he found it difficult to
orchestrate the electrical and
electronic teams. Last year he
acquired a Fluke 434 Power
Quality Analyzer and started
learning more about power
quality.
Charging up the
learning curve
Benoit wanted to be able to
do basic tests on three-phase
power to get his facts straight
before talking to manufacturers
or electricians. He also wanted
a tool that would provide more
details as he learned more
about power quality. One of
his most important require-
ments was the ability to
share data among the various
parties—sometimes this means
a detailed report but it can also
mean standing at a panel and
looking at a real-time display.
He had to have a tool that his
colleagues inside and outside
of his organization would trust.
The Fluke 434 was a good fit.
Sometimes tracing through
the electrical system can be
challenging. He is careful to
have professional electricians
help make connections and
identify the circuits. Benoit
read the 434 manuals, some
of the Fluke app notes, and
browsed a couple of books, but
mostly he’s learned by looking
at measurements on the 434
and working with equipment
vendors, electricians and PQ
experts.
How Stan Benoit
uses the Fluke 434
Since he got his 434 last
year he has used it almost
constantly. He has applied it
on X-Ray, CAT, MRI, and linear
accelerators. In addition to
troubleshooting, he also uses
the 434 to check power quality
before installing new imaging
systems. And in many cases
he uses it to demonstrate that
power quality is probably not
the cause of a failure.
He really likes the color
graphical display, especially
the connection screens that
help him set things up prop-
erly. The display lets him
share and discuss (argue over)
waveforms and trends in real
time. Then he uses the PC
interface to download the data
to his computer and generate a
complete report. He customizes
his reports to suit his audience,
“I have to talk about this stuff
with doctors and administra-
tors. I have to make it clear.”
For troubleshooting, Benoit
turns first to the three-phase
scope display on the 434 to
check the shape of the voltage
waveform. The phasor display
helps confirm that the connec-
tions are good and gives a
quick snapshot of system
balance.
To help track intermittent
problems, he often uses the
dips and swells mode. In this
mode the 434’s autotrend
capability immediately analyzes
voltage and current without
any setup, identifying changes
as short as ½ line cycle.
While he is in dips and swells
mode, he can run the imaging
system through its paces, cycle
nearby equipment, or trans-
fer to backup power systems
and observe the effects on the
434. On the instrument screen,
Benoit can view the events
using the cursors and zoom
tools while background record-
ing continues.
If he doesn’t turn up
anything in dips and swells
mode, he works the system
over with the 434 in Transient
mode. In transient mode, the
434 can capture and display
even shorter events—down to
5 uS.
Recently Benoit used the
Dips and Swells mode to track
down problem with a mobile
imaging system. The system
was shutting down intermit-
tently and seemed to have
the most trouble during hot
weather. According to Stan,
“We had the recording running
and it looked familiar, like a
paper stripchart recorder. We
saw all three phases drop
when we heard the cool-
ers come on.” These truck-
mounted systems carry their
own cooling systems and a
high inrush current caused
a voltage dip when the fans
came on. During summer
months, demand on the util-
ity is high and voltage levels
can run a bit low, especially
in rural areas that would be
served by a mobile imaging
lab. So during balmy weather
the voltage dips were more
likely to cause the imaging
system to drop off line.”
To judge the quality of
power for a new installa-
tion, or to help rule out power
disturbances as a cause for
equipment problems, he uses
the system monitor function
on the 434. This is the func-
tion he uses most often. With a
single button he can initiate a
comprehensive study of voltage
quality.