Item Brochure
3 Fluke Corporation Fluke 750P Series Pressure Modules
Image Description Application
Fluke 700PTP-1 Pneumatic Test Pump
The Fluke 700PTP-1 is a handheld pres-
sure pump designed to generate either
vacuum to -13 psi/-0.9 bar or pressure to
600 psi/40 bar
The Fluke 700PTP-1 has two pressure
ports:
• ¼” NPT female parallel thread fitting for
the reference gauge or pressure module
• ⅛” NPT female parallel thread fitting for
the unit under test
The Fluke 700PTP-1 features an integral pressure adjustment vernier
which varies the pressurized volume by 2.0 cc over approximately
eleven turns of the vernier knob. The pressure variation achievable
with the vernier will depend on the nominal pressure and total pres-
surized volume, but with a minimum volume and maximum pressure,
the vernier provided 600 ± 20 psi adjustment range. With a minimum
volume and no pressure applied, the vernier can also be used to
provide a 0 to 70˝ H2O range. Larger volumes will provide a smaller
range of adjustment, but greater resolution. The length of the stroke
can be adjusted to limit the maximum output pressure. Maximum
output pressure is adjustable from 2.5 psi to 600 psi.
For use with: Fluke 700 and 750P Series Pressure Modules and the
Fluke 710 and 720 Series Pressure Calibrators
Fluke 700HTP-2 Hydraulic Test Pump
The Fluke 700HTP-1 is designed to gener-
ate pressures up to 10000 psi/700 bar.
The Fluke 700HTP-1 has two pressure
ports:
• ¼” NPT female parallel thread fitting for
the reference gauge or pressure module
• ¼” NPT female parallel thread fitting for
the unit under test
Note: The user must provide a hose with
appropriate end fittings from this port to
the unit under test.
This pump can provide up to 10000 psi using distilled water or
mineral-based hydraulic oil. The pump is operated by pumping
several strokes to prime the system, then switching to high pressure
mode when the resistance increases. An integral pressure adjustment
vernier knob varies the pressurized volume by 0.6 cc. The pressure
variation achievable with the vernier will depend on the nominal
pressure and total pressurized volume, but with a minimum volume,
the vernier provided 150 psi to 3000 psi (at 150 psi nominal) and
3000 psi to 10000 psi (at 3000 psi nominal) adjustment ranges. With
a minimum volume and no pressure applied, the vernier can also be
used to provide a 0 to 1.7 psi range. Larger volumes will provide a
smaller range of adjustment, but greater resolution.
For use with: Fluke 700 and 750P Series Pressure Modules and the
Fluke 710 and 720 Series Pressure Calibrators
Fluke 700LTP-1 Low-Pressure Test Pump
The Fluke 700LTP-1 is a hand operated
pressure pump designed to generate either
vacuum to -12 psi/-.85 bar or pressures to
100 psi/6.9 bar. The Fluke 700LTP-1 has
two pressure ports with push fit connec-
tors. These push fit connectors, one for the
reference port for connection to a Fluke
700 Series Pressure Module and one to
connect to a unit under test, connect to
the supplied test hoses.
The Fluke 700LTP-1 is primarily intended for low pressure applica-
tions. It features a fine adjust vernier with .00145 psi resolution at
low pressures. The pressure variation achievable with the vernier will
depend on the nominal pressure and total pressurized volume, but
with minimum volume and maximum pressure the vernier provides
30 psi ± 6 psi. The adjustable pressure relief valve features a slow-
bleed capability that allows the user to slowly release pressure at a
controlled rate to achieve a desired pressure.
Fluke 700HTH-1 Hydraulic Test Hose
The Fluke 700HTH-1 Hydraulic Test Hose
is a 10000 psi, 700 bar working pressure
test hose. The hose uses self-sealing fit-
tings with easy finger tight connections.
The Fluke 700HTH-1 allows connections to a unit under test from a
Fluke 700HTP-1 hydraulic test pump in use with the Fluke 700 and
750P Series Pressure Modules. The 700HTH-1 is compatible with
water and non-corrosive oil.
Fluke 71X Hose Kit
The Fluke 71X hose kit includes (2) quick
disconnect fittings to connect to the 718
or 719, (3) 1-meter translucent hoses and
one BSP adapter.
For use with: Fluke 718 and 719 Pressure Calibrators
Fluke 700PRV-1 Pressure Relief Valve Kit
The Fluke 700PRV-1 consists of two relief
valves (1360 and 5450 psi) to be used
with the 700HTP-1 Hydraulic Test Pump.
These relief valves will protect the Fluke
pressure modules from damage due to
over-pressurization. ¼ BSP male parallel
thread to fit Fluke 700HTP-1.
Repeatability ± 10 % of nominal setting. Multiturn adjustment screw
to set preload on internal disc springs.
For use with: Fluke 700HTP-2 Hydraulic Test Pump.
Fluke 700 PMP Pressure Pump
The Fluke 700PMP is a hand-operated
pressure pump to provide pressures up
to 150 psi/1000 kPa. Output fitting is
⅛ FNPT.
Linear stroke of 1.6 in (4 cm). Multi-turn vernier for fine adjustment of
pressure. Includes controlled pressure bleed valve.
For use with: Fluke 700 and 750P Series Pressure Modules and the
Fluke 710 and 720 Series Pressure Calibrators.
Pressure accessories