Datasheet

6 Fluke Corporation ScopeMeter 190 Series II
190-062 190-102 190-202 190-104 190-204 190-504
Input voltage range
Rated maximum floating voltage CAT III 1000 V/CAT IV 600 V (maximum voltage between any contact and earth-ground voltage level)
Probe input voltage VPS410 CAT III 1000 V/CAT IV 600 V (Maximum voltage between 10:1 probe tip and reference lead)
Probe input voltage VPS510 CAT III 300 V (Maximum voltage between 10:1 probe tip and reference lead)
Maximum BNC input voltage CAT IV 300 V (maximum voltage on BNC input directly)
Maximum voltage
on meter input
CAT III 1000 V/CAT IV 600 V
(safety designed banana input connectors)
—
Memory save and recall
Memory locations (internal) 30 waveform memories plus 10 recording memories plus 9 screen copy memories
15 waveform memory locations Stores scope-trace waveform data (2 or 4 traces each) plus screen-copy plus corresponding setup
Two recording memories Each may contain:
• a 100 Screen Replay sequence, or
• a ScopeRecord Roll-mode recording (2 or 4 traces), or
• a TrendPlot recording of up to 4 measurements
External data storage • On PC, using FlukeView™ Software, or
• Direct storage on external flash memory drive (maximum 2 GB) through USB host port
Screencopies • On PC, using FlukeView™ Software, or
• Internally (in instrument) which can be copied on to external flash memory drive as .BMP-file, through USB
host port
Volatility Measurement data is initially stored in RAM, which is maintained by the main battery with a 30 seconds
back-up when battery is exchanged. When storing data, this is written in non-volatile flash-ROM.
Real-time clock Provides date and time stamp information for ScopeRecord, for 100 Screen Replay sequences and
for TrendPlot recordings.
Case
Design Rugged, shock-proof with integrated protective holster. Handstrap and hangstrap included as standard
Kensington lock supported to lock down instrument when left unattended.
Drip and dust proof IP 51 according to IEC60529
Shock and vibration Shock 30 g, vibration (sinusoidal) 3 g according to MIL-PRF-28800F Class 2
Display size 127 mm x 88 mm (153 mm/6.0 in diagonal) LCD
Resolution 320 x 240 pixels
Contrast and brightness User adjustable, temperature compensated
Brightness 200 cd/m
2
typical using power adapter, 90 cd/m
2
typical using battery power
Mechanical data
Size 265 mm x 190 mm x 70 mm (10.5 in x 7.5 in x 2.8 in)
Weight (including battery) 2.1 kg (4.6 lb) 2.2 kg (4.8 lb)
Power
Line power Mains adapter/battery charger BC190 included, version depending of country
Battery power Re-chargeable double capacity Li-Ion battery (included). Battery swappable through
easily accessible battery door at the rear of the instrument
Battery type (incl.) and capacity
[+opt. battery]
BP290: 2400 mAh
[BP291 (4800 mAh) optional]
BP291: 4800 mAh
Battery charge indicator Battery has built-in status indicator for use with external charger, next to battery status indicator on
instrument screen.
Battery operating time
(with backlight low)
Up to four hours using BP290 (included),
Up to eight hours using BP291 (optional)
Up to seven hours using BP291 (included)
Battery charging time 2½ hours using BP290; 5 hours using BP291 Five hours BP291
Battery power saving functions Auto ‘power down’ with adjustable power down time
Auto ‘Display off’ with adjustable power down time
On-screen battery power indicator
Safety
Compliance EN61010-1-2001, Pollution Degree 2;
CAN/CSA C22.2, No. 61010-1-04, with approval; UL61010B; ANSI/ISA-82.02.01
General Specifications