Cut Sheet

®
Inrush Current Ranges Accuracy
Current ranges (selectable) 1 A, 5 A, 10 A, 50 A, 100 A, 500 A, 1000 A
Inrush times (selectable) l s, 5 s, 10 s, 50 s, 100 s, 5 min
Cursor readings A peak max at cursor 1 and cursor 2 ± 5% of full scale
Time between cursors** 4 to 235 pixels ± (0.2% + 2 pixels)
Scope, dual channel scope with measurement reading
Input impedance
Input 1 1 MΩ//12 pF; with BB120: 20 pF ± 2 pF; with BB120 ±3 pF
Input 2 1 MΩ//10 pF; with BB120: 18 pF ± 2 pF; with BB120 ±3 pF
Vertical
Voltage ranges 50 mV/div to 500V/div ± (1% + 2 pixels)
Vertical sensitivity, resolution 5 mV/div to 500V/div, 8 bit (256 levels)
Bandwidth input 1 (voltage) DC to 20 MHz at inputs, or with BB120 and VPS100-R probe (Opt);
1 MHz with TL24 Leads
Bandwidth input 2 (current) DC to 15 kHz at inputs
10 kHz with 80i-500s Current Clamp
Coupling DC, AC (10 Hz -3 dB)
Horizontal
TimeBase modes Normal, roll, single
TimeBase ranges 60 s/div to 20 ns/div ± (0.4% + 1 pixel)
Sampling rate 25 MS/s
Record length 512 per channel
(min / max samples)
Trigger source Input 1 or Input 2 or Automatic selection
Trigger mode Automatic Connect-and-View™, Free Run,
Single Shot.
Connect-and-View™ Advanced automatic triggering that recognizes signal patterns and automatically
adjusts triggering, timebase and amplitude. Automatically displays stable pictures
of complex and dynamic signals like motor drive and control signals.
Pre-trigger Up to 10 divisions
Measurement readings, Volts & Amps (DC, AC, AC + DCrms, Peak max, Peak min, Peak min / max ),
per channel selectable Frequency, Duty cycle + or - , Phase, Pulse Width + or -, Crest factor
Ohms, Diode, Continuity, Capacitance
Ohms 500.0 Ω 5.000 kΩ, 50.00 kΩ, 500.0 kΩ, ± (0.6% +5 counts)
5.000 MΩ, 30.00 MΩ
Diode voltage 0 to 3.000 V ± (2% +5 counts)
Continuity, shorts > 1 ms Beeper on at < 30Ω ±5Ω,
Capacitance 50.00 nF, 500.0 nF, 5.000 µF, 50.00 µF, ±(2% +10 counts)
500.0 µF
Temperature*** -100.0 °C to 400.0 °C, ±(0.5% +5 counts)
-200.0 °F to 800.0 °F
Max current, max open circuit volt. 0.5 mA, < 4 V (all functions above)
Memory
Number of screens 20
Optical Isolated RS-232 Interface
To printer Supports HP LaserJet™, DeskJet, Epson FX/LQ and Postscript printers with
optional PAC91 Printer Adapter Cable
To PC FlukeView
®
Power Quality Analyzer software with PM9080 Interface
Adapter included
FlukeView
®
Power Quality Software
Hardware requirements PC or 100% compatible with Windows
®
95, 98, Me, 2000, NT4.0.
** 1 pixel = inrush time/250
*** Requires optional temperature accessory
• Inrush current up to 500A with supplied
current probe
• Use cursors to measure inrush current timing
• Connect-and-View™ scope for quick
waveform display
• Voltage and current channels
• 20MHz bandwidth with optional 10:1 voltage
probe. 15kHz on current channel with
optional current clamp
• FlukeView
®
Power Quality Analyzer software
(included)
• Capture measurement screens for
professional-looking reports
• Log readings to your computer disk drive
• Works with Windows word processing,
spreadsheet and analysis software
• Windows 95 / 98 / Me / 2000 / NT 4.0