709/709H Precision Loop Calibrator Gebruiksaanwijzing January 2013 (Dutch) © 2013 Fluke Corporation. All rights reserved. Specifications are subject to change without notice. All product names are trademarks of their respective companies.
BEPERKTE GARANTIE EN BEPERKING VAN AANSPRAKELIJKHEID Dit product van Fluke is vrij van materiaal- en fabricagefouten gedurende drie jaar vanaf de datum van aankoop. Deze garantie geldt niet voor zekeringen, wegwerpbatterijen of beschadiging door ongeluk, verwaarlozing, verkeerd gebruik of abnormale bedienings- of behandelingsomstandigheden. Wederverkopers zijn niet gemachtigd om enige andere garantie namens Fluke te verstrekken.
Inhoudsopgave Titel Pagina Inleiding .......................................................................................................................... Contact opnemen met Fluke .......................................................................................... Veiligheidsinformatie ...................................................................................................... Pictogrammen ..............................................................................................
709/709H Gebruiksaanwijzing Auto Ramp Time (Automatische stijgtijd) .................................................................. Auto Step Time (Automatische staptijd) .................................................................... Stap- en stijgfuncties ............................................................................................ Automatische stap- en stijgfuncties ...................................................................... Valve Test (Kleppentest) .....................
Inhoudsopgave (vervolg) Trim 4 mA (Afregelen op 4 mA) ................................................................................. Trim 20 mA (Afregelen op 20 mA) ............................................................................. Vast mA-uitgangssignaal instellen ............................................................................. PV Zero (Primaire variabele nulstellen) ..................................................................... Apparaatdiagnose ...........................
709/709H Gebruiksaanwijzing iv
Lijst met tabellen Tabel 1. 2. 3. 4. Titel Pagina Pictogrammen ....................................................................................................................... Standaarduitrusting ............................................................................................................... Toetsen ................................................................................................................................. Door gebruiker te vervangen onderdelen ................
709/709H Gebruiksaanwijzing vi
Lijst met afbeeldingen Afbeelding 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. Titel Pagina Standaarduitrusting ............................................................................................................... Toetsen ................................................................................................................................. Hoofdmenu ............................................................................................................................
709/709H Gebruiksaanwijzing 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38. 39. 40. 41. 42. 43. 44. Scherm Contrast Adjustment ................................................................................................ Scherm Auto Shutdown ........................................................................................................ Scherm Hart Write Enable ............................................................................................
Inhoudsopgave (vervolg) 45. 46. 47. 48. Scherm Data Log .................................................................................................................. Scherm Logging Interval........................................................................................................ Scherm Active Logging ......................................................................................................... Batterij vervangen .................................................................
709/709H Gebruiksaanwijzing x
Inleiding De functies van het product omvatten: De Fluke 709 Precision Loop Calibrator en de 709H Precision HART Loop Calibrator (nauwkeurige luskalibrators, hierna het product of de kalibrator genoemd) kunnen worden gebruikt voor het installeren, kalibreren en controleren van veldtransmitters, kleppen en andere componenten van besturings- en regelsystemen in procesinstallaties. Primaire functies zijn het genereren en meten van mA-signalen in het bereik van 0 mA tot 24 mA.
709/709H Gebruiksaanwijzing De kenmerken van het product omvatten: Contact opnemen met Fluke • Groot display met achtergrondverlichting • Digitale selectieknop met selecteerbare decaderegeling voor eenvoudige gegevensinvoer Neem contact op met Fluke via onderstaande telefoonnummers: • Interactieve menu's • Communicatormodus, leest basisinformatie van het apparaat, voert diagnosetests uit en kan worden gebruikt om de kalibratie van de meeste voor HARTcommunicatie geschikte transmitters in te stelle
Precision Loop Calibrator Veiligheidsinformatie Veiligheidsinformatie Een Waarschuwing geeft omstandigheden en procedures aan die gevaar opleveren voor de gebruiker. Let op wijst op omstandigheden en procedures die het product of de te testen apparatuur kunnen beschadigen. Waarschuwing Ga als volgt te werk om mogelijke elektrische schokken, brand of lichamelijk letsel te voorkomen: • Lees alle veiligheidsinformatie voordat u het product gebruikt.
709/709H Gebruiksaanwijzing Pictogrammen De pictogrammen die op het product en in deze handleiding worden gebruikt, worden in tabel 1 toegelicht. Tabel 1. Pictogrammen Pictogram 4 Betekenis Pictogram Betekenis Aarde Conform relevante Noord-Amerikaanse veiligheidsnormen. AC - wisselstroom Conform richtlijnen van de Europese Unie. DC - gelijkstroom Conform relevante Australische normen. Gevaar. Belangrijke informatie. Zie handleiding.
Precision Loop Calibrator Pictogrammen Tabel 1. Pictogrammen (vervolg) Batterij: CAT II Meetcategorie II is van toepassing bij het testen en meten van stroomkringen die direct zijn aangesloten op stroomafnamepunten van de lage-netspanningsinstallatie. CAT IV Meetcategorie IV is van toepassing bij het testen en meten van stroomkringen die zijn aangesloten op de bron van de lage-netspanningsinstallatie van het gebouw.
709/709H Gebruiksaanwijzing Standaarduitrusting De met het product meegeleverde items staan vermeld in tabel 2 en zijn weergegeven in afbeelding 1. Tabel 2.
Precision Loop Calibrator Standaarduitrusting 1 3 2 5 100% 25% 4 0% MENU EXIT 6 7 gzx002.eps Afbeelding 1.
709/709H Gebruiksaanwijzing Het product Tabel 3. Toetsen De volgende paragrafen hebben betrekking op de kenmerken en functies van het product. Toets De toetsen Afbeelding 2 en tabel 3 tonen de plaats en geven een korte beschrijving van de toetsen van het product. Druk op deze toets om de stap- of stijgfunctie te activeren. Druk op deze toets om de achtergrondverlichting in en uit te schakelen. Druk op deze toets om het product in en uit te schakelen.
Precision Loop Calibrator Het product De selectieknop Hoofdmenu Met de selectieknop kunt u de benodigde functies selecteren en regelen en door de menu's van het product navigeren. Draai aan de selectieknop om een menu-item te markeren of een waarde aan te passen. Als de gewenste selectie is gemarkeerd, drukt u op de selectieknop om de geselecteerde actie uit te voeren, of houdt u de knop ingedrukt om aangebrachte wijzigingen op te slaan. Druk op om zonder actie naar het hoofdscherm te gaan.
709/709H Gebruiksaanwijzing Kalibratorinstellingen)” en “Hart Comm. Menu (Menu Hart-comm.)”. Opmerking De items van het “HART”-menu gelden alleen voor de 709H. Opmerking Sommige menu's hebben meerdere schermen. Als dit het geval is, wordt in de hoek linksonder van het menu weergegeven als er na het huidige scherm andere schermen volgen. wordt weergegeven als er aan het huidige scherm andere schermen voorafgaan.
Precision Loop Calibrator Het product mA Source (mA genereren) gebruiken: 1. Selecteer in het hoofdmenu mA Source (mA genereren). 2. Druk op de selectieknop om de decade-cursor te verplaatsen. 3. Draai aan de selectieknop om de uitgang stapsgewijs met de geselecteerde decade te verhogen of verlagen. 4. Druk op , of om de uitgang in te stellen op vooraf geselecteerde waarden. 5. Druk op om deze geavanceerde modi te selecteren en deselecteren.
709/709H Gebruiksaanwijzing mA Simulate (mA simuleren) In de modus mA Simulate (mA simuleren) werkt het product als een 2-draads transmitter en regelt de lusstroom van een externe voeding. Deze functie kan een lus met de transmitter verwijderd testen. Afbeelding 5 toont het beginscherm van de modus mA Simulate (mA simuleren) en de gebruikelijke aansluitingen voor deze modus. mA Simulate (mA simuleren) gebruiken: 1. Selecteer in het hoofdmenu mA Simulate (mA simuleren). 2.
Precision Loop Calibrator Het product mA Measure (mA meten) In de modus mA Measure (mA meten) geeft het product de lusstroommeting weer. Deze modus is zonder 24 V. Afbeelding 6 toont het beginscherm van de modus mA Measure (mA meten) en de gebruikelijke aansluitingen voor deze modus. 4mA- tot 20mAuitgangsapparaat 4 mA tot 20 mA mA Measure (mA meten) gebruiken: Selecteer in het hoofdmenu mA Measure (mA meten). Na selectie opent het product het beginscherm van de modus mA Measure (mA meten).
709/709H Gebruiksaanwijzing mA Measure with 24V (mA meten met 24 V) In de modus mA Measure with 24V (mA meten met 24 V) levert het product 24 V DC terwijl het de lusstroom weergeeft. In deze modus kan een transmitter worden gevoed zonder dat er een afzonderlijke voeding nodig is. Afbeelding 7 toont het beginscherm en de gebruikelijke aansluitingen voor deze modus. gzx006.eps Afbeelding 7.
Precision Loop Calibrator Het product mA Measure with 24 V (mA meten met 24 V) gebruiken: 1. Selecteer in het hoofdmenu mA Measure with 24 V (mA meten met 24 V). Na selectie opent het product het beginscherm van de modus mA Measure with 24 V (mA meten met 24 V). Spanningsuitgangsapparaat 250Ω wordt in de hoek rechtsonder weergegeven als in het instelmenu (Setup) de HART-weerstand is geactiveerd.
709/709H Gebruiksaanwijzing Calibrator Setup Menu (Menu Kalibratorinstellingen) Het Calibrator Setup Menu (menu Kalibratorinstellingen) heeft twee personenschermen. Om naar het tweede scherm te gaan, selecteert u in het eerste scherm Other Parameters (Overige parameters). Scherm 1 is te zien in afbeelding 9 en scherm 2 is te zien in afbeelding 10. gzx22.eps Afbeelding 10. Instelmenu, scherm 2 Opmerking Het menu-item “HART Write Enable” (HART schrijven toegestaan) wordt alleen weergegeven op de 709H.
Precision Loop Calibrator Calibrator Setup Menu (Menu Kalibratorinstellingen) Auto Ramp Time (Automatische stijgtijd) Auto Step Time (Automatische staptijd) Met de functie Auto Ramp Time (Automatische stijgtijd) wordt de stijgtijd over de volle schaal voor de mAstijgfunctie ingesteld. De waarde kan worden ingesteld van 5 seconden tot 300 seconden. Druk op de selectieknop om de decade-cursor te verplaatsen. Draai aan de selectieknop om de waarde stapsgewijs met de geselecteerde decade in te stellen.
709/709H Gebruiksaanwijzing Stap- en stijgfuncties Automatische stap- en stijgfuncties Voor de stap- en de stijgfunctie kunnen de procenttoetsen worden gebruikt om de milliampère-uitgang in te stellen op 0% van het bereik, op 100% van het bereik of om de uitgang stapsgewijs met 25% van het bereik in te stellen. Automatische stap- en automatische stijgfunctie gebruiken: 1. Gebruik het hoofdmenu om het product in te stellen op het genereren of het simuleren van stroom. 2.
Precision Loop Calibrator Calibrator Setup Menu (Menu Kalibratorinstellingen) Valve Test (Kleppentest) Met de functie Valve Test (Kleppentest) wordt de kleppentestfunctie in- of uitgeschakeld. Zie afbeelding 13. gzx25.eps Afbeelding 13. Scherm Valve Test Enable De kleppentest controleert of kleppen goed werken.
709/709H Gebruiksaanwijzing HART 250Ω Resistor mA Span (mA-bereik) De functie HART 250Ω Resistor Enable (HART 250weerstand activeren) schakelt de HART-weerstand in en uit. Zie de paragraaf “HART Resistor (HART-weerstand)” van deze handleiding. Zie afbeelding 14. mA Span is het eerste item in het tweede menu voor het instellen van de kalibrator. Met de functie mA Span (mA-bereik) wordt het stapinterval voor de automatische mA-stapfunctie ingesteld.
Precision Loop Calibrator Calibrator Setup Menu (Menu Kalibratorinstellingen) Contrast Auto Shutdown Time (Tijd voor automatische uitschakeling) Met de Contrast-functie wordt het contrast van het display ingesteld. Draai aan de selectieknop om het contrast in te stellen. Het bereik wordt aangegeven door de bargraph. Een hoger contrast wordt aangegeven door een langere balk. Met de opties Sample normal video (Normaal beeld) en Sample reverse video (Geïnverteerd beeld) kunt u beide tekstmodi beoordelen.
709/709H Gebruiksaanwijzing HART Write Enable (HART schrijven toegestaan) HART Write Enable (HART schrijven toegestaan) is de laatste functie in het instelmenu van de kalibrator. Zie afbeelding 18. Om de instelling te kunnen wijzigen, moet er een wachtwoord worden ingevoerd. Het wachtwoord is in de fabriek ingesteld op 617. Het instelbereik van deze waarde is van 000 tot 999. Zie afbeelding 19. De optie voor schrijven toegestaan wordt alleen opgeslagen nadat het juiste wachtwoord is ingevoerd.
Precision Loop Calibrator Communicatie met HART-apparaten Communicatie met HART-apparaten De HART-functies zijn alleen beschikbaar in de 709H. De automatische uitschakelfunctie wordt gedeactiveerd wanneer u de HART-menu's gebruikt. Wanneer u de HART menu's verlaat, wordt de automatische uitschakelfunctie naar de vorige status teruggezet. Opmerking Afregeling van de lusstroom wordt ondersteund voor transmitters maar niet voor actuatoren.
709/709H Gebruiksaanwijzing In het circuit, externe lusvoeding In de modus mA Measure (mA meten) bevindt het product zich in het circuit en wordt de lusvoeding extern geleverd. In afbeelding 20 is de HART-weerstand van 250 Ω geactiveerd. Activeer de HART-weerstand niet als de lus reeds 250 Ω heeft. 24V-voeding 4 mA tot 20 mA gyj008.eps Afbeelding 20.
Precision Loop Calibrator Communicatie met HART-apparaten In het circuit, lusvoeding door product In de modus mA Measure with 24V (mA meten met 24 V) bevindt het product zich in het circuit en wordt de lusvoeding geleverd door het product. In afbeelding 21 is de HART-weerstand van 250 Ω geactiveerd. Activeer de HART-weerstand niet als de lus reeds 250 Ω heeft. gzx009.eps Afbeelding 21.
709/709H Gebruiksaanwijzing Over het circuit, alleen communicatie In de modus Communicator Only (Alleen communicator) is het product over het circuit aangesloten en wordt de 24V-voeding lusvoeding extern geleverd. In afbeelding 22, met het product in de modus Communicator Only (Alleen communicator), moet er een weerstand van 250 Ω in de lus aanwezig zijn. 4 mA tot 20 mA RL ≥ 250 Ω gyj010.eps Afbeelding 22.
Precision Loop Calibrator Communicatie met HART-apparaten Communicatie instellen en selecteren Voor alle bedrijfsmodi van het hoofdscherm, behalve mA Measure with 24V (mA meten met 24 V) of Volts Measure (Spanning meten), wordt de bedrijfsmodus op mA Measure (mA meten) ingesteld als u het HART Comm. Menu (menu Hart-comm.) opent. De bedrijfsmodus blijft hetzelfde als het hoofdscherm als de modus Measure with 24V (Meten met 24 V) is.
709/709H Gebruiksaanwijzing Modus Met de functie Mode (Modus) in hetHART. Comm. Menu (menu Hart-comm.) kunt u de modus selecteren waarin u wilt werken. Zie afbeelding 24. Resistor (250Ω-weerstand) is standaard ingesteld op n/a (niet van toepassing). 250Ω Resistor (250Ω-weerstand) Met de functie 250Ω Resistor (250Ω-weerstand) kunt u de 250Ω-weerstand in- en uitschakelen. Gebruik de selectieknop om de weerstand op de gemarkeerde selectie in te stellen en terug te gaan naar het instelselectiescherm.
Precision Loop Calibrator Communicatie met HART-apparaten HART Connect (HART-aansluiting) De functie HART Connect (HART-aansluiting) lokaliseert het HART-apparaat in de lus. Voordat er een bewerking met een HART-apparaat mogelijk is, moet het apparaat worden gelokaliseerd in de lus. Dit gebeurt door alle mogelijke apparaatadressen te pollen en een apparaat uit de adressen te selecteren die met de zoekopdracht overeenkomen. eenmaal per seconde langer wordt naarmate de bewerking vordert. Zie afbeelding 26.
709/709H Gebruiksaanwijzing Tag-selectie Acquiring Data (Gegevens verzamelen) Het tag-selectiescherm toont alle lange tag-namen die tijdens het pollen werden gevonden. Tag-namen kunnen indien nodig twee regels beslaan om alle tekst weer te geven. Het scherm Acquiring Data (Gegevens verzamelen) wordt weergegeven terwijl het product alle configuratiegegevens van het apparaat verzamelt. De reeks punten wordt eenmaal per seconde langer om de voortgang van de bewerking aan te geven.
Precision Loop Calibrator Communicatie met HART-apparaten Disconnect from Loop (Van lus loskoppelen) Function Select Menu (Menu Functie selecteren) Het scherm Disconnect from Loop (Van lus loskoppelen) wordt weergegeven voordat het product naar het beginscherm van de functie terugkeert zodat het product van de lus kan worden losgekoppeld. Zie afbeelding 29. Het menu Function Select (Functie selecteren) is in afbeelding 30 weergegeven. gzx39.eps Afbeelding 30. Menu Function Select gzx38.
709/709H Gebruiksaanwijzing Device Setup and Data (Apparaatinstellingen en -gegevens) Het scherm Device Setup and Data (Apparaatinstellingen en -gegevens) omvat 11 schermen met de indeling zoals weergegeven in afbeelding 31. Elk scherm bevat maximaal 6 gegevenspunten. Een item kan indien nodig meer dan één regel beslaan om de volledige tekst weer te geven. Als een gegevensitem niet wordt ondersteund in het HART-apparaat, is dit gemarkeerd als n/a (niet beschikbaar).
Precision Loop Calibrator Onderste en bovenste bereikwaarden schrijven Onderste en bovenste bereikwaarden schrijven Opmerking Bij de schermen in deze paragraaf kunnen de tagnamen indien nodig worden afgekapt zodat ze op één regel passen. knippert in de rechter bovenhoek om een spanningvoerende aansluiting aan te geven. Als de HART-schrijfopdrachten niet actief zijn, zijn deze functies niet beschikbaar en wordt er een foutmelding weergegeven in plaats van het scherm in afbeelding 32.
709/709H Gebruiksaanwijzing 4. Druk op om naar het menu Function Select (Functie selecteren) te gaan. Er wordt eerst een herinnering weergegeven om de lus in AUTOMATIC (automatisch) te veranderen. 3. Houd de knop ingedrukt om de nieuwe waarde naar het HART-apparaat te sturen en in dit display te blijven. Er wordt een fout weergegeven wanneer het HART-apparaat de waarde afwijst. Druk op om naar het menu LRV (onderste bereikwaarde) en URV (bovenste bereikwaarde) te gaan.
Precision Loop Calibrator Menu voor Trim, Set en Zero (Afregelen, Instellen en Nulstellen) Gebruik de selectieknop om de betreffende actie te selecteren en te starten. Druk op om naar het menu Function Select (Functie selecteren) te gaan. Trim 4 mA (Afregelen op 4 mA) Als de bedrijfsmodus Communicator Only (Alleen communicator) is, is deze functie niet beschikbaar en wordt er een foutmelding weergegeven. Voordat u doorgaat, krijgt u het verzoek om de lus te wijzigen in MANUAL (handmatig).
709/709H Gebruiksaanwijzing Trim 20 mA (Afregelen op 20 mA) Als de bedrijfsmodus Communicator Only (Alleen communicator) is, is deze functie niet beschikbaar en wordt er een foutmelding weergegeven. Voordat u doorgaat, krijgt u een waarschuwing om de lus te wijzigen in MANUAL (handmatig). Druk op de selectieknop om door te gaan. Druk op om naar het menu voor Trim, Set en Zero (Afregelen, Instellen en Nulstellen) te gaan.
Precision Loop Calibrator Menu voor Trim, Set en Zero (Afregelen, Instellen en Nulstellen) Vast mA-uitgangssignaal instellen Als de bedrijfsmodus Communicator Only (Alleen communicator) is, is deze functie niet beschikbaar en wordt er een foutmelding weergegeven. Voordat u doorgaat, krijgt u een waarschuwing om de lus te wijzigen in MANUAL (handmatig). Druk op de selectieknop om door te gaan. Druk op om naar het menu voor Trim, Set en Zero (Afregelen, Instellen en Nulstellen) te gaan.
709/709H Gebruiksaanwijzing PV Zero (Primaire variabele nulstellen) 1. Voordat u doorgaat, krijgt u een waarschuwing om de lus te wijzigen in MANUAL (handmatig). Druk op de selectieknop om door te gaan. Druk op om naar de menu's voor Trim, Set en Zero (Afregelen, Instellen en Nulstellen) te gaan. Druk op de selectieknop om het HART-apparaat op nul te stellen en in dit scherm te blijven om het resultaat te evalueren.
Precision Loop Calibrator Apparaatdiagnose Apparaatdiagnose Opmerking Bij de schermen in deze paragraaf kunnen de tag-namen indien nodig worden afgekapt zodat ze op één regel passen. knippert in de rechter bovenhoek om een spanningvoerende aansluiting aan te geven. Als de HART-schrijfopdrachten niet actief zijn, is deze functie niet beschikbaar en wordt er een foutmelding weergegeven.
709/709H Gebruiksaanwijzing Draai aan de selectieknop om tussen de fouten heen en weer te schakelen. 1. Druk op om naar het menu Function Select (Functie selecteren) te gaan. Er wordt eerst een herinnering weergegeven om de lus in AUTOMATIC (automatisch) te veranderen. Configuration Log en Data Log (Configuratielogboek en Gegevenslogboek) Configuration Log en Data Log (Configuratielogboek en Gegevenslogboek) zijn alleen beschikbaar als het product op een HART-apparaat is aangesloten.
Precision Loop Calibrator Apparaatdiagnose Aanbevolen wordt om een LEMO-USB-kabel en 709H/TRACK-software te gebruiken. Er is een adapter van USB naar serieel die gebruikmaakt van een FTDIchipset. Deze combinatie zorgt voor een consistente en betrouwbare communicatie tussen het product en de pc. De stuurprogramma's voor USB bevinden zich op de cd met 709H/TRACK-software. Het nummer en de inhoud van de opslagpositie worden bovenaan weergegeven.
709/709H Gebruiksaanwijzing Bewerking SEND (VERZENDEN): • Als de positie leeg is, wordt er een foutmelding weergegeven. • Als de positie in gebruik is, stuurt u de gegevens in rapportformaat naar de RS-232-poort. Data Log (Gegevenslogboek) Procesgegevens kunnen voor een afzonderlijke tag worden opgeslagen om later met de Windows-software 709H/TRACK naar een pc te worden geüpload. Zie de paragraaf “Configuration Log (Configuratielogboek)” van deze handleiding voor meer informatie.
Precision Loop Calibrator Apparaatdiagnose Bewerking START (STARTEN): • Als er geen vrije records of vrije sessies over zijn, of als het huidige HART-apparaat niet overeenkomt met het reeds gelogde HART-apparaat, wordt er een foutmelding weergegeven. • Is dat niet het geval, ga dan door met de hieronder beschreven intervalselectie. Draai aan de selectieknop om de markering te verplaatsen en het gewenste interval te selecteren. Druk op de selectieknop om het loggen met dat interval te starten.
709/709H Gebruiksaanwijzing Hieronder volgen de weergegeven gegevensitems: • Onderhoud De bovenste regel geeft aan of er wordt gelogd (Logging) of dat het loggen is gestopt (Stopped). Het loggen stopt automatisch wanneer het geheugen vol is of voordat het product wordt uitgeschakeld omdat de batterij de spanningsgrenswaarde van 5,6 V voor automatische uitschakeling heeft bereikt. Voor veilig gebruik en onderhoud van het product: • Bij lekkage van de batterij, het product eerst repareren vóór gebruik.
Precision Loop Calibrator Onderhoud Product reinigen Zekering Reinig het product en de drukmodules met een zachte doek bevochtigd met water of met water en zachte zeep. Het product wordt door een interne zelf-resettende zekering beveiligd tegen overstroom. De zekering wordt binnen enkele seconden automatisch gereset. De zekering kan niet handmatig worden gerepareerd. Let op Ga als volgt te werk om beschadiging van het product te voorkomen: • Gebruik geen oplosmiddelen of schurende reinigingsmiddelen.
709/709H Gebruiksaanwijzing Batterijen vervangen Vervang de batterijen wanneer de batterij-indicator op het display wordt weergegeven. Batterijen vervangen: 1. Verwijder de holster. 2. Draai het product om zodat het display naar beneden wijst. 3. Verwijder met een platte schroevendraaier de schroeven van de batterijklep. 4. Verwijder de batterijen. 5. Vervang de oude batterijen. Let op de juiste polariteit wanneer u de nieuwe batterijen installeert. 6. Plaats de batterijklep. 7.
Precision Loop Calibrator Door gebruiker te vervangen onderdelen Door gebruiker te vervangen onderdelen De door de gebruiker te vervangen onderdelen zijn weergegeven in tabel 4. Voor meer informatie over deze items en hun prijs, kunt u contact opnemen met een Fluke vertegenwoordiger. Zie de paragraaf “Contact opnemen met Fluke”. Tabel 4. Door gebruiker te vervangen onderdelen Onderdeel Fluke-onderdeelnr.
709/709H Gebruiksaanwijzing Tabel 4. Door gebruiker te vervangen onderdelen (vervolg) Onderdeel 48 Fluke-onderdeelnr.
Precision Loop Calibrator Specificaties Specificaties Bereiken mA .................................................... 0 mA tot 24 mA Spanning ........................................... 0 V DC tot 30 V DC Resolutie mA-bereiken...................................... 1 μA Spanningsbereik ............................... 1 mV Nauwkeurigheid...................................... 0,01% ±2 digits in alle bereiken (bij 23 °C ±5 °C) Stabiliteit .................................................
709/709H Gebruiksaanwijzing Elektromagnetische omgeving ................ IEC 61326-1 (draagbare apparatuur) Afmetingen (LxBxD) ................................ (152 x 93 x 44) mm, (6,0 x 3,7 x 1,7) inch Gewicht ...................................................