Brochure
717/718/718Ex
Pressure Calibrators
10033-eng Rev. 08
C43 (718) C125 (717) TL220 700P27 700LTP
Pump up the pressure
717 pressure Calibrators
•
Measure pressure, 0.05% of full scale
with internal sensor
- 1/8 NPT pressure fitting
- Compatible with non-corrosive gasses
and liquids
•
Pressure measurement to 700 bar using
any of the Fluke-700Pxx Pressure Modules
•
Wide range of selectable measurement
units for pressure
•
Current measurement with 0.015%
accuracy and 0.001mA resolution
•
Simultaneous pressure and current
measurement for easy p/I or I/p testing
•
24 volt loop power supply
•
Zero, Min-Max, Hold and Damping
functions
•
Pressure switch test captures set, reset
and deadband values
718 Pressure Calibrators
•
Same features as Fluke 717 plus
•
Newly designed built-in pressure/vacuum
hand pump with vernier and bleed valve
helps protect the pump from damage and
is easier to clean
718Ex 30G and 100G Intrinsically
Safe Pressure Calibrator
•
Same features as Fluke 718
(excl. loop supply)
•
For use in explosion endangered areas
•
ATEX certified ( II 1G EEx ia IIC T4)
•
Compatible with eight intrinsically safe
pressure modules
Included Accessories
Fluke 717: Yellow Holster (H80M excl. TPAK),
TL75 Test Leads and AC72 Alligator Clips,
Single 9V alkaline battery (two 9V batteries in
718), Instructions. 718/718Ex: 718: Yellow
Holster, 718Ex: Red Ex Holster, TL75 Test Leads
and AC72 Alligator Clips, 700ILF In-Line Filter,
two 9V batteries, user manual on CD-ROM.
Ordering Information
Fluke 718 1G Pressure Calibrator
Fluke 718 30G Pressure Calibrator
Fluke 718 100G Pressure Calibrator
Fluke 718 300G Pressure Calibrator
Fluke 718Ex 30G Intrinsically Safe
Pressure Calibrator
Fluke 718Ex 100G Intrinsically Safe
Pressure Calibrator
Fluke 717 1G Pressure Calibrator
Fluke 717 30G Pressure Calibrator
Fluke 717 100G Pressure Calibrator
Fluke 717 300G Pressure Calibrator
Fluke 717 500G Pressure Calibrator
Fluke 717 1000G Pressure Calibrator
Fluke 717 1500G Pressure Calibrator
Fluke 717 3000G Pressure Calibrator
Fluke 717 5000G Pressure Calibrator
Specifications
For Fluke 717/718 models: Supported Pressure Units; psi, in. H
2
O(4°C), in. H
2
O(20°C), cm H
2
O(4°C),
cm H
2
O(20°C), bar mBar, kPa, inHg, mmHg, kg/cm
2
Functions: Zero, Min, Max, Hold, Damp functions
Max. Voltage: 30 V
Operating temperature: -10°C to 55°C
Safety: CSA C22.2 No. 1010.1:1992
EMC: EN50082-1:1992 and EN55022:1994 Class B
Fluke 717: For use with non corrosive gasses and liquids
Fluke 718: For use with non corrosive gasses
717
Size (HxWxD): 201 mm x 98 mm x 52 mm
Weight: 0.6 kg
Warranty: Three years
718/718Ex
Size (HxWxD): 216 mm x 94 mm x 66 mm
Weight: 0.992 kg
Warranty 718: Three years
Warranty 718Ex: One year
Fluke 718
Model Range Resolution Over Pressure
718 1G -68.9 mbar to 68.9 mbar 0.001 mbar Over Pressure 5xFS
718 30G -850 mbar to 2 bar 0.1 mbar Over Pressure 2xFS
718 100G -850 mbar to 7 bar 0.1 mbar Over Pressure 2xFS
718 300G -850 mbar to 20 bar 1 mbar Over Pressure 375 PSI, 25 bar
717 1G -68.9 mbar to 68.9 mbar 0.001 mbar Over Pressure 5xFS
717 30G -850 mbar to 2 bar 0.1 mbar Over Pressure 2xFS
717 100G -850 mbar to 7 bar 0.1 mbar Over Pressure 2xFS
717 300G -850 mbar to 20 bar 1 mbar Over Pressure 375 PSI, 25 bar
717 500G 0 mbar to 34.5 bar 1 mbar Over Pressure 2xFS
717 1000G 0 mbar to 69 bar 1 mbar Over Pressure 2xFS
717 1500G 0 bar to 103.4 bar 0.01 bar Over Pressure 2xFS
717 3000G 0 bar to 207 bar 0.01 bar Over Pressure 2xFS
717 5000G 0 bar to 345 bar 0.01 bar Over Pressure 2xFS
Fluke 717
Fluke 718Ex
Recommended Accessories
(Not for hazardous zones)