Datasheet

ManualsBrandsFluke ManualsMechanical Test InstrumentsFluke 805FC Vibration Meter with Fluke Connect, 0.01 ... 50 g

Fluke 805 FC

Vibration Meter

The reliable, repeatable, accurate way to

check bearings and overall vibration.

Make go or no-go maintenance decisions with

confidence. The Fluke 805 FC Vibration Meter is the

most reliable vibration screening device available

for frontline mechanical troubleshooting teams that

need repeatable, severity-scaled readings of overall

vibration and bearing condition.

What makes the Fluke 805 FC the most reli-

able vibration screening device available?

• Innovative sensor design minimizes measure-

ment variations caused by device angle or contact

pressure

• Consistent data quality at both low and high

frequency ranges

• Four-level severity scale assesses urgency of

problems for overall vibration and bearing condition

• Exportable data via USB

• Trending in Microsoft

Excel using pre-built

templates

• Overall vibration measurement (10 Hz to 1,000 Hz)

for acceleration, velocity and displacement units of

measurement for a wide variety of machines

• Crest Factor+ technology provides reliable bearing

assessment using direct sensor tip measurements

between 4,000 Hz and 20,000 Hz

• Compare vibration levels with ISO-10816 severity

scales and store results to the Fluke Connect Cloud

• Get authorization to take next steps in an instant if

machine health is at risk via Fluke Connect

™

ShareLive

™ video call*

• Colored lighting system (green, red) and on-screen

comments indicate how much pressure needs to be

applied to take measurements

• Temperature measurement with Spot IR Sensor

increases diagnostic capabilities

• On-board memory holds and saves up to 3,500

measurements

• External accelerometer support for hard to reach

locations

• Flashlight for viewing measurement locations in

dark areas

• Large screen with high resolution for easy navigation

and viewing

What is Crest Factor +?

Built with

See it. Save it. Share it.

All the facts, right in the field.

Now compatible with

Fluke Connect

™

Mobile App

Technical Data

Smart phone not included with purchase.

Fluke Connect with ShareLive

™

is the only wireless measurement

system that lets you stay in contact with your entire team without

leaving the field*. The Fluke Connect mobile app is available for

Android™ (4.3 and up) and iOS (4s and later) and works with

over 20 different Fluke products—the largest suite of connected

test tools in the world. And more are on the way. Go to the Fluke

website to find out more.

Make the best decisions faster than ever before by viewing all

temperature, mechanical, electrical and vibration measurements

for each equipment asset in one place. Get started saving time

and increasing your productivity.

Download the app at:

*Within provider’s wireless service area.

Summary of content (4 pages)

PAGE 1
Fluke 805 FC Vibration Meter Technical Data Now compatible with Fluke Connect ™ Mobile App The reliable, repeatable, accurate way to check bearings and overall vibration. Make go or no-go maintenance decisions with confidence. The Fluke 805 FC Vibration Meter is the most reliable vibration screening device available for frontline mechanical troubleshooting teams that need repeatable, severity-scaled readings of overall vibration and bearing condition.
PAGE 2
What is Crest Factor +? Fluke 805 FC with Crest Factor + takes the confusion out of bearing assessment The original Crest Factor is used by vibration analysts to identify bearing faults. It is defined as the ratio of the peak value/RMS value of a time domain vibration signal. A key limitation of using Crest Factor to identify bearing faults is that the Crest Factor does not increase linearly as the bearing degrades.
PAGE 3
Use the Fluke 805 FC Vibration Meter to check these machine categories: Chiller (refrigeration) • Reciprocating (Open motor and compressor separate) • Reciprocating (Hermetic motor and compressor) • Centrifugal (Hermetic or Open Motor) Fans • Belt-driven Fans 1800 to 3600 RPM • Belt-driven fans 600 to 1799 RPM • General direct drive fans (direct coupled) • Vacuum blowers (belt or direct drive) • Large forced draft fans (fluid film brgs.) • Large induced draft fans (fluid film brgs.
PAGE 4
Technical specifications Vibration meter Low frequency range (overall measurement) High frequency range (CF+ measurement) Severity levels 10 Hz to 1,000 Hz 4,000 Hz to 20,000 Hz Good, Satisfactory, Unsatisfactory, Unacceptable 50 g peak (100 g peak-peak) 16-bit 80 dB Vibration limit A/D converter Signal to noise ratio Sampling rate Low frequency 20,000 Hz High frequency 80,000 Hz Real time clock backup Coin battery Sensor Sensitivity 100 mV / g ± 10 % Measurement range 0.