LinkRunner Duo Network MultiMeter Quick Reference Guide TM Welcome Thank you for purchasing Fluke Networks LinkRunner Duo! This test tool enables you to quickly verify Ethernet copper/fiber cables, network connectivity and availability. In addition, the instrument provides multiple tools for identifying the network device to which it is connected, identifies PoE ports, provides a Report generating function, and can serve as a reflector (optional feature) for Fluke Networks performance tests.
Cleaning To prevent moisture from entering the LinkRunner Duo, clean it with a moist cloth only. Do not use organic solvents, acid, or alkali solutions. Safety Information The following symbols are used on the product and in this document: j W ) NOT FOR CONNECTION TO PUBLIC TELEPHONE SYSTEMS * CLASS 1 LASER PRODUCT.
External Features - Connections, Buttons, and the LED 1. RJ-45 LAN port 1 2. SFP 1000BASE-X fiber adapter port 2 3. Power Button 4. 5. 6. 7.
Navigation Home screen – Displays link, speed/duplex, length, utilization, security authentication, connection, and wire map information. PING screen – Displays (scrolling from left to right) a Tx/Rx summary of all devices to the right which will include: the Router, DHCP, DNS, and each user configured IP address. LLDP (IEEE), EDP (Extreme Networks), CDP (CISCO) screen – Displays the switch address (MAC or IP), switch name, slot/port, VLAN ID (optional), and VOIP VLAN Reply ID (optional).
1 1. 2. 3. 4. 5. Scroll up thru the functions Scroll right within a function Scroll down thru the functions Scroll left within a function Select a function 4 2 5 3 Is this an active RJ45 LAN port? Note: If both the RJ45 LAN and 1000BASE-X fiber ports are connected to your network, LinkRunner Duo will try to link to the RJ45 LAN port first. If link has been established over fiber and you connect also to the RJ45 LAN port, no change in link will occur. Cable/Link Status: 1.
Is this an active Fiber port? 1. Fiber/Link Status: 2. Advertised speed/duplex 3. Actual link speed/duplex 4. The optical signal strength being received by the SFP if DDM (digital diagnostic monitoring) is supported by the SFP. Blank indicates no DDM. 1 5 2 10 3 6 4 9 Note: The SFP power measurement accuracy is based on the SFP manufacturer’s specification. 7 8 5. Navigation arrows. Indicates which buttons are active. 6. Highlighted function is the active function.
Home – Link Information and Wire Map functions Note: Wire Map and PoE detection do not apply when connecting to your network through the 1000BASE-X SFP fiber adapter. The Home screen displays link or Ethernet wire map information depending on the connection. If the RJ-45 Ethernet cable is connected from the RJ-45 LAN port to your network, LinkRunner Duo will display link information which will include link, speed/duplex, cable length to the network connection, and network utilization.
Additional Home Screen Messages LinkRunner Duo is discovering over Ethernet LinkRunner Duo is discovering/authenticating 802.1X LinkRunner Duo is discovering over fiber Detected 802.1X, but failed to authenticate Detected 802.1X, but LinkRunner Duo is not configured for 802.1X Un-powered Device Token Ring Telco The PING function contains several screens that are accessed by scrolling to the right.
Duplicate IP addresses found is shown as follows: See the configuration for procedures to set up PING IP addresses. LLDP, CDP, EDP The LLDP, CDP, EDP function displays the switch address (MAC for LLDP, IP for CDP, MAC for EDP), switch name, slot/port information (if available), and VLAN information (if available ) such as VLAN ID and VOIP VLAN Reply ID. The first switch discovered is displayed first. Up to 5 switches can be displayed and are accessed by scrolling to the right.
Reflector Mode (optional feature) Enables packet reflector mode, which allows the instrument to be used as a remote device for the Fluke Networks network performance tests. Use the Configuration screen to set up the parameters. Saving Reports Allows you to save the report summary information which contains the current Home screen, PING screen, and LLDP, EDP, CDP screen. Saved reports must be viewed on a PC using the LinkRunner Connect PC application.
User Preferences When FDX is selected, forces the unit to use full duplex for non-negotiating ports (this option can only be enabled when the Reflector option is enabled) ; Select “.1X” to enable 802.1X security. This allows the unit to link to an 802.1X secure switch; Select the cable length units as either feet or meters; Set the power off timeout to either 10 minutes or infinity. Use the right arrow key to toggle units and the center button to save. You can configure 802.
Selecting the IP number/name to edit: When is highlighted, press the selection button (center). Use the up/down arrow keys to choose the IP number and the selection button to select it. Notice at the bottom of the display, the IP name changes as you scroll thru the 10 IP numbers. By default the names are IP1 – IP10. Editing the IP address to PING: Then, using the down arrow key, move down to the IP address. Press the selection button (center).
Reflector Mode configuration (optional feature) Highlight the packet type and then use the up or down arrow key to select the packet type that the reflector will respond to: - any packet - destination MAC is this LinkRunner Duo and the data string contains a special Fluke Networks byte string (generated by the Fluke Networks instrument) - the data string contains a special Fluke Networks byte string - destination MAC is this LinkRunner Duo - any non-broadcast packet Highlight the swap icon and then use the
Firmware update Allows you to download the latest LinkRunner Duo firmware through the LinkRunner Connect PC application. Firmware updates can be downloaded from www.flukenetworks.com/linkrunnerduo. Navigate to the LinkRunner Duo product page and follow the links for downloads and updates. Press the right arrow to update. Use the LinkRunner Connect PC application to download the update files. Note: If the batteries are too low during the firmware update, you will get an error message. Replace the batteries.
Agency Certification and Approval ) ; Canadian Standards Association certified to Canadian and US standards Meets C-Tick EMC standard, N10140, complies with FCC Part 15 Class A N10140 P Conforms to European Union Directives Pollution Degree 2 Laser * Class 1 Laser Product, complies with 21 CFR 1040.10 & 1040.11, CFR(J), and EN608251:1994/A1:1997/A2:2002 General Specifications Media Access Cable Tests Tone Generator 10BASE-T, 100BASE-TX, 1000BASE-T, 1000BASE-X, and PoE (IEEE 802.
Security Operational Security IEEE 802.1X option for network authentication. Note: LinkRunner Duo supports the following 802.1X encryption key sizes: 512, 768, 1024, 1280, 1536, 1792, and 2048 bits.