User's Manual

ManualsBrandsFluke ManualsTestersFluke T5-1000

PN 686953

March 1998 Rev.1, 9/01

T5-600/T5-1000

Electrical Tester

Service Information

Introduction

This service information sheet provides the following information for the T5-600 and T5-1000 Electrical

Testers (hereafter referred to as "the tester").

• Safety information

• Parts and service information

• Specifications

• Cleaning procedure

• Required equipment

• Performance tests

• Parts and accessories list

• Battery replacement procedure

For operating instructions, refer to the T5-600/T5-1000 Electrical Tester Instruction Sheet.

Safety Information

Warning

To avoid possible electric shock or personal injury, follow these guidelines:

• Do not use the tester if it is damaged or operating abnormally. Protection

may be impaired.

• Before each use:

• Make sure the battery door is closed and latched.

• Inspect the tester and test leads. Look for cracks, missing plastic, exposed

metal, or damaged insulation. Replace damaged test leads before using the

tester.

• Verify the tester’s operation by measuring a known voltage.

• Replace the batteries as soon as the low battery indicator (M) appears.

• Do not use the tester around explosive gas, vapor or dust.

• Do not apply more than the rated voltage, as marked on the tester, between

terminals or between any terminal and earth ground.

• Refer servicing to qualified personnel.

• Use caution when working above 30 V ac rms, 42 V ac peak, or 60 V dc.

• When using the probes, keep your fingers behind the finger guards on the

probes.

• Connect the common test lead before you connect the live test lead.

Disconnect the live test lead first.

• The display will not display hazardous voltages in display hold. The voltage

indicator LED (

) continues to operate.

Summary of content (9 pages)

PAGE 1
® T5-600/T5-1000 Electrical Tester Service Information Introduction This service information sheet provides the following information for the T5-600 and T5-1000 Electrical Testers (hereafter referred to as "the tester"). • • • • • • • • Safety information Parts and service information Specifications Cleaning procedure Required equipment Performance tests Parts and accessories list Battery replacement procedure For operating instructions, refer to the T5-600/T5-1000 Electrical Tester Instruction Sheet.
PAGE 2
T5-600/T5-1000 Electrical Tester Parts and Service The tester is warranted to be free from defects in material and workmanship for two years, while under normal use. Parts and repairs are warranted for 90 days. For the complete warranty statement, refer to the T5-600/T5-1000 Electrical Tester Instruction Sheet.
PAGE 3
Service Information Serial Numbers 79559999 and Below General Specifications (continued) RF Field Specification 0.5 % full scale + (specified accuracy) at 3 V/m Safety Complies with ANSI/ISA-S82.01-94, UL Classified to IEC 61010, CSA/CAN C22.2 No.1010.192, and EN61010-1 1995. EMC EN 61326 Certifications In accordance with IEC 61010-1 54CJ Resolution and Accuracy Function T5-600 Range T5-1000 Range Resolution Accuracy K 600 V rms 1000 V rms 1V ±(1.
PAGE 4
T5-600/T5-1000 Electrical Tester General Specifications (continued) Shock, Vibration 1 m drop at 15 °C to 35 °C (59 °F to 95 °F) per ANSI/ISA-S82.01-1994 and EN 61010-1 1993. Sinusoidal vibration per MIL-PRF-28800F for a Class 2 instrument (5 Hz to 55 Hz, 3 g maximum) Surge Protection T5-600: 6 kV per IEC 1010-1, 1990-09: T5-1000: 8 kV per IEC 1010-1, 1990-09 Enclosure Rating IP 52 per IEC 60529, no vacuum applied RF Field Specification 0.
PAGE 5
Service Information Equipment Required for Performance Tests Equipment Required for Performance Tests The following equipment is required for performance tests: • Fluke 5500A Multi-Product Calibrator, or equivalent • 0 V to 5 V adjustable dc power supply • Approximately 8 m (26 ft) of #14 single-conductor magnet wire wound into a butterfly-shaped coil. Figure 1 shows how to make the coil. Performance Tests Use the following procedures to verify the tester’s performance.
PAGE 6
T5-600/T5-1000 Electrical Tester 10 turns of #14 single-conductor magnet wire Separate into two 5-turn coils. 21 cm (~8.25") Use cable ties to hold coils together Mount Banana plugs on wire end Connect to Calibrator qp7f.eps Figure 1.
PAGE 7
Service Information Performance Tests Testing the Voltage Functions The tests in this section check the following voltage functions: • Automatic selection of ac or dc voltage mode • Correct operation of the hazardous voltage indicator • Correct operation of the HOLD function Perform the tests as follows: 1. Set the calibrator to the T5-600 or T5-1000 test voltage given in Table 2. 2. Apply the voltage to the tester. Verify that the tester reads within the display limits shown. 3.
PAGE 8
T5-600/T5-1000 Electrical Tester Resistance and Continuity Function Tests 1. Set the calibrator to the resistance given in Step 1 of Table 5. 2. Apply the resistance to the tester. Verify that the tester reads within the display limits shown. 3. Apply the resistances and verify the tester’s responses for the remaining steps in Table 5. Table 5.
PAGE 9
Service Information Battery Replacement Table 6. Replacement Parts and Accessories (continued) Description Fluke Part Number T5-600/T5-1000 Electrical Tester Instruction Sheet (International) 1621978 H5 Belt Holster Accessory TP1 Probe Set, Flat Blade Accessory TP4 Probe Set, 4 mm Round Accessory Battery Replacement Figure 2 shows how to replace the batteries. Observe the polarity markings inside the battery compartment. qp1.eps Figure 2.