The FWR7102 High Speed Router User’s Guide V1.
Table of Contents 1 2 3 4 5 Preface ........................................................................................................................................................................................................................................................................................................... 4 LED Indicators and Connectors .............................................................................................................................................
6 7 5.3.2 LAN ..................................................................................................................................................................................................................................................................................... 29 5.3.3 DMZ/Port Forward ................................................................................................................................................................................................
1 Preface Thank you for choosing FW R7102 wireless router with VoIP. This product will allow you to make ATA call using your broadband connection, and provides W i-Fi router function. This manual provides basic information on how to install and connect FW R7102 wireless router with VoIP to the Internet. It also includes features and functions of wireless router with VoIP components, and how to use it correctly.
2 LED Indicators and Connectors Before you use the high speed router, please get acquainted with the LED indicators and connectors first. 2.
Front Panel LED PHONE1/2 W LAN Status Explanation Blinking(Green) Not registered. On (Green) Registered On (Green) W ireless access point is ready. Blinking(Green) It will blink while wireless traffic goes through. Blinking(Green) 4G connected Off 4G not connected On (Green) The port is connected with 100Mbps. Off The port is disconnected. Blinking(Green) The data is transmitting. On(Green) The port is connected with 100Mbps. Off The port is disconnected.
2.2 Hardware Installation Before starting to configure the router, you have to connect your devices correctly. Step 1.Connect Line port to land line jack with a RJ-11 cable. Step 2.Connect the W AN port to a modem or switch or router or Internet with an Ethernet cable. Step 3.Connect one port of 4 LAN ports to your computer with a RJ-45 cable. This device allows you to connect 4 PCs directly. Step 4.Connect one end of the power cord to the power port of this device.
3 Voice Prompt In any circumstance, pressing the following command to enter relevant function. The following table lists command, and description. Voice Menu Setting Options Operation code 1 2 3 4 Contents Step 1.Pick up phone and press “****” to start IVR Step 2.Choose “1”, and FWR7102 report the current WAN port connection type Step 3.Prompt "Please enter password”, user need to input password with end char # if user want to configuration WAN port connection type.
5 6 7 8 9 0 Step 1.Pick up phone and press “****” to start IVR Step 2.Choose “5”, and FWR7102 report current DNS Step 3.Input the new DNS and with the end char # using “*” to replace “.”, user can input 192*168*20*1 to set the new gateway 192.168.20.1 press # (pound) key to indicate that you have finished 3) Report “operation successful” if user operation properly. If you want to quit by the wayside, press “**”. Step 1.Pick up phone and press “****” to start IVR Step 2.
W hen using Voice Menu, press * (star) to return the main menu. If any changes made in the IP assignment mode, please reboot the FW R7102 to take the setting into effect. W hen enter IP address or subnet mask, use “*”(Star) to replace “.” (Dot). For example, to enter the IP address 192.168.20.159 by keypad, press these keys: 192*168*20*159,use the #(pound) key to indicate that you have finished entering the IP address.
4 Configuring Basic Settings 4.1 Two-Level Management This chapter explains how to setup a password for an administrator/root user and how to adjust basic/advanced settings for accessing Internet successfully. FW R7102 supports two-level management: administrator and user. For administrator mode operation, please type “admin/admin” on Username/Password and click Login button to configuration.
user mode operation, please type “user/user” on Username/Password and click Login for full configuration. Notice: If you fail to access to the web configuration, please go to “Trouble Shooting” for detecting and solving your problem. 4. The web page can be logged out after 5 minutes without any operation. 4.2.2 From WAN port 1. Make sure your PC can connect to the router’s WAN port correctly. 2. Getting the IP addresses of W AN port using Voice prompt. 3.
4.3 Webpage No . N a me Description 1 Navigation bar Click navigation bar, many sub-navigation bar will appear in the place 2 2 Title Click sub-navigation bar to choose one configuration page 3 Parameter To configuration parameters the Every time making some changes, user should press this button to confirm the changes. After pressing the button, the red will appear to rebooting. notice To cancel the changes.
4.4 Setting up the Time Zone Open Administration/Management webpage as shown below, please select the Time Zone for the router installed and specify the NTP server and set the update interval in NTP synchronization. 4.5 Setting up the Internet Connection Open the Network/WAN webpage as shown below; please select the appropriate IP Mode according to the information from your ISP. There are three types offered in this page, which are Static, DHCP and PPPoE.
4.5.1 Static IP You will receive a fixed public IP address or a public subnet, namely multiple public IP addresses from your DSL or Cable ISP service providers. In most cases, a Cable service provider will offer a fixed public IP, while a DSL service provider will offer a public subnet. If you have a public subnet, you could assign an IP address to the W AN interface.
Set the DNS Mode from Auto and Manual, If user choose manual, you should fill the DNS Mode primary DNS address and Secondary DNS address into Primary DNS Address and Secondary DNS Address. Primary DNS Type in the primary IP address for the route Server Secondary DNS Type in secondary IP address for necessity in the Server future 4.5.3 PPPoE PPPoE stands for Point-to-Point Protocol over Ethernet. It relies on two widely accepted standards: PPP and Ethernet.
Assign a specific valid user name PPPoE Account provided by the ISP Assign a valid password provided by PPPoE Password the ISP Confirm Input the password again Password Set the DNS Mode from Auto and Manual, If user choose manual, you should fill DNS Mode the primary DNS address and Secondary DNS address into Primary DNS Address and Secondary DNS Address.
4.6 Setting up the Wireless Connection To set up the wireless connection, please skip the following steps. 4.6.1 Enable Wireless and Setting SSID Open Wireless/Basic webpage as shown below Click the button to enable or disable wireless. Radio On/Off Press to disable wireless. Press to enable wireless. Network Mode Choose one network mode from the drop down list. Network The name of the wireless name, it can be any text Nmae(SSSID) numbers or various special characters.
Choose one SSID from Off-premises 1, off-premises SSID Choice 2 and Premises. Select an appropriate encryption mode to improve the security and privacy of your wireless data Security Mode packets. Each encryption mode will bring out different web page and ask you to offer additional configuration. 4.7 Register 4.7.1 Get the Accounts FW R7102 have 2 phone port, you can use it to make SIP call, and before registering, you should get the SIP account from you administrator or provider. 4.7.
4.7.3 Configuration SIP from Webpage Step 1.Open SIP Account/Line 1 webpage, as the picture in the right side. Step 2.Fill the SIP Server domain and SIP Server address (which get from you administrator or provider) into Domain Name parameter, into SIP Server Step 3.Fill account which get from you administrator into Display Name parameter, Phone Number parameter, and Account parameter. Step 4.Fill password which get from you administrator into Password parameter. Step 5.
4.8 Make Call 4.8.1 Calling phone or extension numbers To make a phone or extension number call: a) Both ATA and the other VoIP device (i.e., another ATA or other SIP products) have public IP addresses, or b) Both ATA and the other VoIP device (i.e., another ATA or other SIP products) are on the same LAN using private or public IP addresses, or c) Both ATA and the other VoIP device (i.e., another ATA or other SIP products) can be connected through a router using public or private IP addresses.
4.8.5 Attended Transfer Assuming that call party A and B are in conversation. A wants to Attend Transfer B to C: Step 1.Party A dial “*77” to hold the party B, when hear the dial tone, A dial C’s number, then party A and party C are in conversation. Step 2.Party A dial “*78” to transfer to C, then B and C now in conversation. Step 3.If the transfer doesn’t success, then A and B in conversation again. 4.8.6 Conference Assuming that call party A and B are in conversation.
5 Web Configuration This chapter will guide users to execute advanced (full) configuration through admin mode operation. 5.1 Login Step 1.Connect the LAN port of the router to your PC Step 2.Open a web browser on your PC and type in http://192.168.1.1. The window will ask for typing username and password. And you can choose language, too.
The page 24 of 58 Revision time: 2016-07-07
5.2 Status This webpage shows the status information about product information, Network and system. It shows the basic information of the product, such as product name, serial number, MAC address, hardware version and software version. It also shows the information of Link Status, W AN Port Status, and LAN Port Status. And it shows the current time and the running time of the product. The picture in the right side is the FW R7102’s Status webpage. 5.
5.3.1 WAN This page allows you to set W AN configuration with different modes. Use the Connection Type drop down list to choose one W AN mode and then the corresponding page will be displayed. Static IP: You will receive a fixed public IP address or a public subnet, namely multiple public IP addresses from your DSL or Cable ISP service providers. In most cases, a Cable service provider will offer a fixed public IP, while a DSL service provider will offer a public subnet.
DHCP: It is not necessary for you to type any IP address manually. Simply choose this type and the system will obtain the IP address automatically from DHCP server. Set the DNS Mode from Auto and Manual, If user choose manual, you should fill the DNS Mode primary DNS address and Secondary DNS address into Primary DNS Address and Secondary DNS Address.
PPPoE Account Assign a specific valid user name provided by the ISP PPPoE Password Assign a valid password provided by the ISP PPPoE Auto-Dial If or not enable PPPoE Password. Set the DNS Mode from Auto and Manual, If user choose manual, you should fill the primary DNS DNS Mode address and Secondary DNS address into Primary DNS Address and Secondary DNS Address.
5.3.2 LAN LAN Port: The most generic function of router is NAT. W hat NAT does is to translate the packets from public IP address to local IP address to forward the right packets to the right host and vice versa. Type in local IP address for connecting to a local private Local IP Address network (Default: 192.168.1.1) Type in an address code that determines the size of the Local Subnet Mask network. (Default: 255.255.255.0/ 24) If or not enable DHCP server.
DHCP Ending Enter a value of the IP address pool for the DHCP server to end Address with when issuing IP addresses. Primary/Secondary Input the primary or secondary DNS IP address. DNS You must specify a DNS server IP address here because your ISP should provide you with usually more than one DNS Primary DNS Server. If your ISP does not provide it, the router will automatically apply default DNS Server IP address: 202.96.134.33 to this field.
DMZ Host IP Enter the private IP address of the DMZ host Address Port Forward 5.3.4 MAC Clone Some ISPs will require you to register your MAC address. If you do not wish to re-register your MAC address, you can have the router clone the MAC address that is registered with your ISP. To use the Clone Address button, the computer viewing the W eb-base utility screen will have the MAC address automatically entered in the Clone W AN MAC field.
Step 1.Press button to clone the currently PC MAC address to router’s Internet port. Step 2.Press Step 3.Press button to save the changes button to make changes effective 5.3.
5.4 Wireless 5.4.1 Basic Select Radio On to enable the wireless, select Radio Off Radio On/Off to disable wireless. Network Mode Choose one network mode from the five types. The name of the wireless name, it can be any text SSID numbers or various special characters. The default SSID is "Wireless_7102". Multiple User can set multiple SSID. SSID1-3 broadcast(SSID) If or not enable SSID broadcast.
5.4.2 Security Choose one SSID from SSID, Multiple SSID1, SSID Choice Multiple SSID2 and Multiple SSID3. Select an appropriate encryption mode to improve the security and privacy of your wireless data packets. Security Mode Each encryption mode will bring out different web page and ask you to offer additional configuration. 5.4.3 WMM 5.4.
WPS If or not enable WPS. Press the button to apply. 5.4.
5.4.
5.5 SIP Account 5.5.
5.5.
5.5.
5.6 Phone 5.6.
5.6.
5.6.
5.6.
5.7 Security 5.7.
5.7.2 DMZ 5.7.
5.7.
5.7.
5.8 Administration 5.8.
5.8.2 Firmware Upgrade 1) Choose upgrade file type from Image File and Dial Rule 2) Press 3) Press to browser file. to start upgrading. 5.8.3 Provision Please refer to the provision user manual to test provision.
The page 50 of 58 Revision time: 2016-07-07
5.8.
5.8.5 TR069 5.9 System Log If you enable the system log in Status/syslog webpage, you can view the system log in this webpage.
5.10 Logout Press the logout button to logout, and then the login window will appear.
5.11 Reboot Press the Reboot button to reboot FW R7102.
6 Trouble shooting of the guide Setting your PC gets IP automatically Following are the process of setting your PC gets IP automatically Step 1.Click the “begin” Step 2.Select “control panel”, then double click “network connections” in the “control panel” Step 3.Right clicks the “network connection” that your PC uses, select “attribute” and you can see the interface as picture 1: Step 4.
6.1 Can not connect to the configuration Website Solution: Check if the Ethernet cable is properly connected, then Check if the URL is right wrote, the format of URL is: http:// the IP address: 8080, 8080 must be added, then Check if the version of IE is IE8, or use other browser such as Firefox or Mozilla, then Contact your administrator, supplier, or ITSP for more information or assistance. 6.
7 Statement FCC Radiation Exposure Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, many cause harmful interference to radio communications.
environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
