User's Manual

ManualsBrandsFlyingvoice Technology ManualsComputers & AccessoriesVoIP Wireless Router

V1.0

The page 1 of 57

Revision time: 2016-02-24 18:00

The FWR7202

VoIP Wireless Router

User’s

Guide

V1.0

Summary of content (57 pages)

PAGE 2
Copy Right 2016 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.0 Table of Contents 1 2 3 4 5 Preface ....................................................................................................................................................................................................................................................................................................................4 LED Indicators and Connectors .........................................................
PAGE 3
Copy Right 2016 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.0 5.3.4 5.3.5 6 7 MAC Clone...................................................................................................................................................................................................................................................................................30 Multi WAN .........................................................................................................................
PAGE 4
Copy Right 2016 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.0 1 Preface Thank you for choosing FW R7202 wireless router with VoIP. This product will allow you to make ATA call using your broadband connection, and provides W i-Fi router function. This manual provides basic information on how to install and connect FW R7202 wireless router with VoIP to the Internet. It also includes features and functions of wireless router with VoIP components, and how to use it correctly.
PAGE 5
Copy Right 2016 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.0 2 LED Indicators and Connectors Before you use the high speed router, please get acquainted with the LED indicators and connectors first.
PAGE 6
Copy Right 2016 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.0 2.1 LED Indicators Front Panel LED PHONE1/2 W LAN LAN 1/2/3/4 W AN Status Explanation Blinking(Green) Not registered. On (Green) Registered On (Green) Wireless access point is ready. Blinking(Green) It will blink while wireless traffic goes through. On (Green) The port is connected with 100Mbps. Off The port is disconnected. Blinking(Green) The data is transmitting. On(Green) The port is connected with 100Mbps.
PAGE 7
Copy Right 2016 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.0 2.2 Hardware Installation Before starting to configure the router, you have to connect your devices correctly. Step 1.Connect Line port to land line jack with a RJ-11 cable. Step 2.Connect the W AN port to a modem or switch or router or Internet with an Ethernet cable. Step 3.Connect one port of 4 LAN ports to your computer with a RJ-45 cable. This device allows you to connect 4 PCs directly. Step 4.
PAGE 8
Copy Right 2016 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.0 3 Voice Prompt In any circumstance, pressing the following command to enter relevant function. The following table lists command, and description. Voice Menu Setting Options Operation code 1 2 3 4 5 Contents Step 1.Pick up phone and press “****” to start IVR Step 2.Choose “1”, and FWR7202 report the current WAN port connection type Step 3.
PAGE 9
Copy Right 2016 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.0 6 7 8 9 0 Step 1.Pick up phone and press “****” to start IVR Step 2.Choose “6”, and FWR7202 report “Factory Reset” Step 3.Prompt "Please enter password", the method of inputting password is the same as operation 1.  If you want to quit by the wayside, press “*”. Step 4.Prompt “operation successful” if password is right and then FWR7202 will be factory setting. Step 5.Press “7” reboot to make changes effective. Step 1.
PAGE 10
Copy Right 2016 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.0  #(pound) key to i ndicate that you have fi nish entering the IP address or subnet mask  W hen assigning IP address in Static IP mode, setting IP address, subnet mask and default gateway is a must. If in DHCP mode, please make sure that DHCP SERVER is available in your existing broadband connection to which W AN port of FW R7202 is connected.  The default LAN port IP address of FW R7202 is 192.168.1.
PAGE 11
Copy Right 2016 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.0 4 Configuring Basic Settings 4.1 Two-Level Management This chapter explains how to setup a password for an administrator/root user and how to adjust basic/advanced settings for accessing Internet successfully. FW R7202 supports two-level management: administrator and user. For administrator mode operation, please type “admin/admin” on Username/Password and click Login button to configuration.
PAGE 12
Copy Right 2016 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.0 Notice: If you fail to access to the web configuration, please go to “Trouble Shooting” for detecting and solving your problem. 4. The web page can be logged out after 5 minutes without any operation. 4.2.2 From WAN port 1. Make sure your PC can connect to the router’s W AN port correctly. 2. Getting the IP addresses of W AN port using Voice prompt. 3. Open a web browser on your PC and type http://the IP address of WAN port.
PAGE 13
Copy Right 2016 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.0 N o. Name Description 1 Navigation bar C l i ck navigation bar, many sub-navigation bar will appear in the place 2 2 Title Click sub-navigation bar to choose one configuration page 3 Parameter To configuration the parameters  Every time making some changes, user should press this button to confirm the changes.  After pressing the button, the red will appear to notice rebooting. To cancel the changes.
PAGE 14
Copy Right 2016 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.0 4.5 Setting up the Internet Connection Open the Network/WAN webpage as shown below; please select the appropriate IP Mode according to the information from your ISP. There are three types offered in this page, which are Static, DHCP and PPPoE.
PAGE 15
Copy Right 2016 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.0 4.5.1 Static IP You will receive a fixed public IP address or a public subnet, namely multiple public IP addresses from your DSL or Cable ISP service providers. In most cases, a Cable service provider will offer a fixed public IP, while a DSL service provider will offer a public subnet. If you have a public subnet, you could assign an IP address to the W AN interface.
PAGE 16
Copy Right 2016 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.0 Set the DNS Mode from Auto and Manual, If user choose manual, you should fill the DNS Mode primary DNS address and Secondary DNS address into Primary DNS Address and Secondary DNS Address. Primary DNS Type in the primary IP address for the route Server Secondary DNS Type in secondary IP address for necessity in the Server future 4.5.3 PPPoE PPPoE stands for Point-to-Point Protocol over Ethernet.
PAGE 17
Copy Right 2016 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.0 Assign a specific valid user name PPPoE Account provided by the ISP Assign a valid password provided by PPPoE Password the ISP Confirm Input the password again Password Set the DNS Mode from Auto and Manual, If user choose manual, you should fill DNS Mode the primary DNS address and Secondary DNS address into Primary DNS Address and Secondary DNS Address.
PAGE 18
Copy Right 2016 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.0 Click the button to enable or disable wireless. Radio On/Off Press to disable wireless. Press to enable wireless. Network Mode Choose one network mode from the drop down list. Network The name of the wireless name, it can be any text Nmae(SSSID) numbers or various special characters. Multiple SSSD1-3 Set more wireless network. Frequency Choose channel frequency. 4.6.
PAGE 19
Copy Right 2016 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.0 4.7.2 Connections Connect FW R7202 to the Internet properly 4.7.3 Configuration SIP from Webpage Step 1.Open SIP Account/Line 1 webpage, as the picture i n the right side. Step 2.Fill the SIP Server domain and SIP Server address (which get from you administrator or provider) into Domain Name parameter, into SIP Server Step 3.
PAGE 20
Copy Right 2016 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.0 4.8 Make Call 4.8.1 Calling phone or extension numbers To make a phone or extension number call: a) Both ATA and the other VoIP device (i.e., another ATA or other SIP products) have public IP addresses, or b) Both ATA and the other VoIP device (i.e., another ATA or other SIP products) are on the same LAN using private or public IP addresses, or c) Both ATA and the other VoIP device (i.e.
PAGE 21
Copy Right 2016 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.0 To make a direct IP call, first pick up the analog phone or turn on the speakerphone on the analog phone, Input the IP address directly, with the end “#”. 4.8.3 Call Hold W hile in conversation, pressing the “*77” to put the remote end on hold, then you will hear the dial tone and the remote party will hear hold tone at the same time. Pressing the “*77” again to release the previously hold state and resume the bi-directional media.
PAGE 22
Copy Right 2016 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.0 5 Web Configuration This chapter will guide users to execute advanced (full) configuration through admi n mode operation. 5.1 Login Step 1.Connect the LAN port of the router to your PC Step 2.Open a web browser on your PC and type in http://192.168.1.1. The window will ask for typing username and password. And you can choose language, too.
PAGE 24
Copy Right 2016 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.0 5.2 Status This webpage shows the status information about product information, Network and system. It shows the basic information of the product, such as product name, serial number, MAC address, hardware version and software version. It also shows the information of Link Status, W AN Port Status, and LAN Port Status. And it shows the current time and the runni ng time of the product.
PAGE 25
Copy Right 2016 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.0 5.3 Network&Security You can configuration the W AN port, LAN port, DDNS, Multi W AN,DMZ, MAC Clone,Port Forward and so on in these two bars. 5.3.1 WAN This page allows you to set W AN configuration with different modes. Use the Connection Type drop down list to choose one W AN mode and then the corresponding page will be displayed.
PAGE 26
Copy Right 2016 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.0 Set the DNS Mode from Auto and Manual, If user choose manual, you should fill the DNS Mode primary DNS address and Secondary DNS address into Primary DNS Address and Secondary DNS Address. Type in the primary IP address for the Primary DNS Server route Type in secondary IP address for Secondary DNS Server necessity in the future PPPoE: PPPoE stands for Point-to-Point Protocol over Ethernet.
PAGE 27
Copy Right 2016 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.0 PPPoE Account Assign a specific valid user name provided by the ISP PPPoE Password Assign a valid password provided by the ISP PPPoE Auto-Dial If or not enable PPPoE Password. Set the DNS Mode from Auto and Manual, If user choose manual, you should fill the primary DNS DNS Mode address and Secondary DNS address into Primary DNS Address and Secondary DNS Address.
PAGE 28
Copy Right 2016 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.0 5.3.2 LAN LAN Port: The most generic function of router is NAT. W hat NAT does is to translate the packets from public IP address to local IP address to forward the right packets to the right host and vice versa. Type in local IP address for connecting to a local private Local IP Address network (Default: 192.168.1.1) Type in an address code that determines the size of the Local Subnet Mask network. (Default: 255.255.255.
PAGE 29
Copy Right 2016 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.0 Address with when issuing IP addresses. Primary/Secondary Input the primary or secondary DNS IP address. DNS You must specify a DNS server IP address here because your ISP should provide you with usually more than one DNS Primary DNS Server. If your ISP does not provide it, the router will automatically apply default DNS Server IP address: 202.96.134.33 to this field.
PAGE 30
Copy Right 2016 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.0 Port Forward 5.3.4 MAC Clone Some ISPs will require you to register your MAC address. If you do not wish to re-register your MAC address, you can have the router clone the MAC address that is registered with your ISP. To use the Clone Address button, the computer viewing the W eb-base utility screen will have the MAC address automatically entered in the Clone W AN MAC field.
PAGE 31
Copy Right 2016 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.0 Step 1.Press button to clone the currently PC MAC address to router’s Internet port. Step 2.Press Step 3.Press button to save the changes button to make changes effective 5.3.5 Multi WAN Note: Muti-wan only used in WAN connection mode,not in LTE mode 5.4 Wireless 5.4.
PAGE 32
Copy Right 2016 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.0 Select Radio On to enable the wireless, select Radio Off Radio On/Off to disable wireless. Network Mode Choose one network mode from the five types. The name of the wireless name, it can be any text SSID numbers or various special characters. The default SSID is "Wireless_7202". Multiple User can set multiple SSID. SSID1-3 broadcast(SSID) If or not enable SSID broadcast.
PAGE 33
Copy Right 2016 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.0 5.4.2 Security Choose one SSID from SSID, Multiple SSID1, SSID Choice Multiple SSID2 and Multiple SSID3. Select an appropriate encryption mode to improve the security and privacy of your wireless data packets. Security Mode Each encryption mode will bring out different web page and ask you to offer additional configuration. 5.4.3 WMM 5.4.
PAGE 48
Copy Right 2016 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.0 5.8.2 Firmware Upgrade 1) Choose upgrade file type from Image File and Dial Rule 2) Press 3) Press to browser file. to start upgrading. 5.8.3 Provision Please refer to the provision user manual to test provision.
PAGE 51
Copy Right 2016 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.0 5.8.5 TR069 5.9 System Log If you enable the system log in Status/syslog webpage, you can view the system log in this webpage.
PAGE 54
Copy Right 2016 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.0 6 Trouble shooting of the guide 6.1 Setting your PC gets IP automatically Following are the process of setting your PC gets IP automatically Step 1.Click the “begin” Step 2.Select “control panel”, then double click “network connections” in the “control panel” Step 3.Right clicks the “network connection” that your PC uses, select “attribute” and you can see the i nterface as picture 1: Step 4.
PAGE 55
Copy Right 2016 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.0 6.2 Can not connect to the configuration Website Solution: Check if the Ethernet cable is properly connected, then Check if the URL is right wrote, the format of URL is: http:// the IP address: 8080, 8080 must be added, then Check if the version of IE is IE8, or use other browser such as Firefox or Mozilla, then Contact your admi nistrator, supplier, or ITSP for more information or assistance. 6.
PAGE 56
Copy Right 2016 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.0 7 Statement FCC Radiation Exposure Statement FlyingVoice Technology Ltd. Declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules.
PAGE 57
Copy Right 2016 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.0 This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.