Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 The G902 High Speed Router User’s Guide V1.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 Table of Contents 1 2 3 4 Preface .................................................................................................................................................................................................................................................................................................................... 5 1.1 Declaration of Conformity..........................................................
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 Status .................................................................................................................................................................................................................................................................................................... 23 Network&Security ...............................................................................
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 4.10 5 Application ........................................................................................................................................................................................................................................................................................... 65 4.10.1 UPnP .....................................................................................................................
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 1 Preface Thank you for choosing G902 wireless router with VoIP. This product will allow you to make ATA call using your broadband connection, and provides Wi-Fi router function. This manual provides basic information on how to install and connect G902 wireless router with VoIP to the Internet. It also includes features and functions of wireless router with VoIP components, and how to use it correctly.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED Reorient or relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4. Consult the dealer or an experienced radio/TV technician for help. V1.1 1. 1.2GNU GPL Information G902 firmware contains third-party software under the GNU General Public License (GPL).
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 2 Overview Before you use the high speed router, please get acquainted with the LED indicators and connectors first. 2.1G900 series 2.1.1 G900 series G902 G902P G901 G901P 1xGE in RJ45 4xGE in RJ45 WAN L AN G900 G900P 2X2 2.4G 802.11 b/g/n WiFi 2X2 5G 802.11ac USB FXS 1X USB 2.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 2.2LED Indicators Front Panel LED PHONE WLAN LAN 1/2/3/4 WAN POWER Rear Panel Status Explanation Blinking(Green) Not registered. On (Green) Registered On (Green) On (Green) Wireless access point is ready. It will blink while wireless traffic goes through. The port is connected with 100Mbps. Off The port is disconnected. Blinking(Green) The data is transmitting. On(Green) The port is connected with 100Mbps.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED Step 1.Connect Line port to land line jack with a RJ-11 cable. Step 2.Connect the WAN port to a modem or switch or router or Internet with an Ethernet cable. Step 3.Connect one port of 4 LAN ports to your computer with a RJ-45 cable. This device allows you to connect 4 PCs directly. Step 4.Connect one end of the power cord to the power port of this device. Connect the other end to the wall outlet of electricity. Step 5.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 Warning: Please do not attempt to use other different power adapter or cut off power supply during configuration or updating the G201N4 VoIP home gateway. Using other power adapter may damage G201N4 and will void the manufacturer warranty. Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 2.4Voice Prompt In any circumstance, pressing the following command to enter relevant function. The following table lists command, and description. Voice Menu Setting Options Operation code 1 Contents Step 1.Pick up phone and press “****” to start IVR Step 2.Choose “1”, and G902 report the current W AN port connection type 2 3 Step 3.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 5 Step 1.Pick up phone and press “****” to start IVR Step 2.Choose “5”, and G902 report current DNS Step 3.Input the new DNS and with the end char # using “*” to replace “.”, user can input 192*168*20*1 to set the new gateway 192.168.20.1 press # (pound) key to indicate that you have finished 3) Report “operation successful” if user operation properly. If tyeopu1w opqp uh itobnyethaendwparyessidse“,**p*r*e” sto s “s*t*a”r.t IVR S .
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 3. When enter IP address or subnet mask, use “*”(Star) to replace “.” (Dot). 4. For example, to enter the IP address 192.168.20.159 by keypad, press these keys: 192*168*20*159,use the #(pound) key to indicate that you have finished entering the IP address. 5. #(pound) key to indicate that you have finish entering the IP address or subnet mask 6.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 3 Configuring Basic Settings 3.1Two-Level Management This chapter explains how to setup a password for an administrator/root user and how to adjust basic/advanced settings for accessing Internet successfully. G902 supports two-level management: administrator and user. For administrator mode operation, please type “admin/admin” on Username/Password and click Login button to configuration.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 3.2.2 From WAN port 1. Make sure your PC can connect to the router’s WAN port correctly. 2. Getting the IP addresses of WAN port using Voice prompt. 3. Open a web browser on your PC and type http://the IP address of WAN port. The following window will be open to ask for username and password. 4. For administrator mode operation, please type “admin/admin” on Username/Password and click Login to configuration.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 will appear to notice rebooting. To cancel the changes. Press it to reboot the router 3.4Setting up the Time Zone Open Administration/Management webpage as shown left, please select the Time Zone for the router installed and specify the NTP server and set the update interval in NTP synchronization.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 3.5Setting up the Internet Connection From WAN page, multi wan connection could be built or deteted. If you want to know more information about Internet Connection setting, please refer to 5.3 section. Field Name Connect Name Service IP Protocol Version Description Use keywords to indicate WAN port service model (the parameters are defined in Network--> multi-WAN page). Please refer to 5.3.1 section. Chose the service mode.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 Field Name Radio On/Off Network Mode SSID Multiple SSSD1-3 Frequency Description Select “Radio Off” to disable wireless. Select “Radio on”to enable wireless. Choose one network mode from the drop down list. The name of the wireless name, it can be any text numbers or various special characters. Set more wireless network. Choose channel frequency.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 3.6.2 Encryption Open Wireless/Wireless Security webpage to set the encryption of routers. Field Name SSID Choice Description Choose one SSID from Off-premises 1, off-premises 2 and Premises. Select an appropriate encryption mode to improve the security and privacy of your wireless Security data packets. Mode Each encryption mode will bring out different web page and ask you to offer additional configuration. 3.7Register 3.7.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 3.7.3 Configuration SIP from Webpage Step 1.Open FXS1(FXS2)/SIP Account webpage, as the picture in the right side. Step 2.Fill the SIP Server domain and SIP Server address (which get from you administrator or provider) into Domain Name parameter, into SIP Server Step 3.Fill account which get from you administrator into Display Name parameter, Phone Number parameter, and Account parameter. Step 4.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 3.8Make Call 3.8.1 Calling phone or extension numbers To make a phone or extension number call: 1. Both ATA and the other VoIP device (i.e., another ATA or other SIP products) have public IP addresses, or 2. Both ATA and the other VoIP device (i.e., another ATA or other SIP products) are on the same LAN using private or public IP addresses, or 3. Both ATA and the other VoIP device (i.e.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 3.8.5 Attended Transfer Assuming that call party A and B are in conversation. A wants to Attend Transfer B to C: Step 1.Party A dial “*77” to hold the party B, when hear the dial tone, A dial C’s number, then party A and party C are in conversation. Step 2.Party A dial “*78” to transfer to C, then B and C now in conversation. Step 3.If the transfer doesn’t success, then A and B in conversation again. 3.8.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 4.2Status This webpage shows the status information, Network and system. information about product It shows the basic information of the product, such as product name, serial number, MAC address, hardware version and software version It also shows the information of Link Status, WAN Port Status, and LAN Port Status. And it shows the current time and the running time of the product.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 4.3Network&Security You can configuration the WAN port, LAN port, DDNS, Multi WAN,DMZ, MAC Clone, Port Forward and so on in these two bars. 4.3.1 WAN This page allows you to set WAN configuration with different modes. Use the Connection Type drop down list to choose one WAN mode and then the corresponding page will be displayed. 1.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 2. DHCP It is not necessary for you to type any IP address manually. Simply choose this type and the system will obtain the IP address automatically from DHCP server. Field Name DNS Mode Primary DNS Address Secondary DNS Address DHCP Renew Description The Default is Manual The primary DNS of Internet port. The secondary DNS of Internet port.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 Field Name PPPoE Account PPPoE Password Confirm Password Operation Mode Description Assign a valid user name provided by the ISP Assign a valid password provided by the ISP Enter your PPPoE password again Select the mode of operation, options are Keep Alive, On Demand and Manual: 1.When the mode is Keep Alive, user need to set the 'keep alive redial period' values range from 0 to 3600s, the default setting is 5 minutes; 2.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 Field Name IP Bridge Bridge Type PPPoE Bridge Hardware IP Bridge DHCP Service Type Pass Through DHCP Snooping Local Service VLAN Mode Disable Enable Trunk VLAN ID 802.1p Description Allow all ethernet packets pass. PC could connect to upper network directly. Only Allow PPPoE packets pass. PC need PPPoE dial-up software. Packets pass through hardware switch with wired speed. Do not support wireless port bind.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 5.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 4.3.2 LAN 1. LAN Port: The most generic function of router is NAT. What NAT does is to translate the packets from public IP address to local IP address to forward the right packets to the right host and vice versa.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 DHCP stands for Dynamic Host Configuration Protocol. The router by factory default acts a DHCP server for your network so it automatically dispatch related IP settings to any local user configured as a DHCP client. It is highly recommended that you leave the router enabled as a DHCP server if you do not have a DHCP server for your network. Field Name Local DHCP Server Description If or not enable DHCP server.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 4.3.3 MAC Clone Some ISPs will require you to register your MAC address. If you do not wish to re-register your MAC address, you can have the router clone the MAC address that is registered with your ISP. To use the Clone Address button, the computer viewing the Web-base utility screen will have the MAC address automatically entered in the Clone WAN MAC field. Enabling MAC address cloning 1.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 4.3.5 DMZ Field Name Description DMZ Enable If or not enable DMZ. DMZ Host IP Enter the private IP address of the DMZ Address host 4.3.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 4.3.7 Port Forward Field Name Description Comment Sets the name of a port mapping rule or comment IP Address The IP address of devices under the LAN port. Port Range Set the port range for the devices under the LAN port. (1-65535) Protocol Apply/Cancel You can select TCP, UDP, TCP & UDP three cases After finish configurations, click apply, the number will be generated under NO.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 4.3.8 Advance Field Name Description Most Nat The largest value which the G902 can connections provide Mss Mode Choose Mss Mode from Manual and Mss Value Auto Set the value of TCP AntiDos-p You can choose to enable or prohibit IP conflict Select enable if enabled, phone IP conflict will have tips or prohibit； detection IP conflict Detecting Detect IP address conflicts of the time interval Interval 4.3.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 4.3.10 QoS Field Name QoS Enable Upstream Delete Selected Add Description If or not enable Qos function Set the upstream bandwidth In NO., Check the items you want to delete, click the Delete option Click Add to add a new parameter 4.3.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 4.4 Wireless 4.4.1 Basic Field Name Radio on/off Wireless connection mode Network Mode SSID Multiple Description Select “Radio Off” to disable wireless. Select “Radio on”to enable wireless. According to the wireless client type, select one of these modes. Default is AP Choose one network mode from the drop down list. Default is 11b/g/n mixed mode It is the basic identity of wireless LAN.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 within the AP. BSSID A group of wireless stations and a WLAN access point (AP) consists of a basic access device (BSS), each computer in the BSS must be configured with the same BSSID, that is, the wireless AP logo. Frequency (Channel) You can select Auto Select and channel HT Physical Mode Operating Mode Channel Bandwidth Guard Interval MCS Reverse Direction （RDG） 1/2/3/4/5/6/7/8/9/10/11. 1.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 Select an appropriate encryption mode to improve the security and privacy of your wireless data Security packets. Mode Each encryption mode will bring out different web page and ask you to offer additional configuration. Select a different encryption mode, the web interface will be different, user can configure the corresponding parameters under the mode you select. Here are some common encryption method: 1.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 WPA Algorithms This item is used to select the security algorithm for encryption of wireless dhome gateway, options are TKIP, AES, TKIPAES three Setting up WPA2-PSK security password Pass phrase Set the key scheduled update cycle, default is 3600s Key Renewal Interval 4.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 computers to access the network. Implementation: As shown, the Policy is Reject, add 00:1F: D0: 62: BA: FF to the MAC, click Save and reboot the device settings to take effect. 4.4.3 WMM WMM (Wi-Fi MultiMedia) is the QoS certificate of Wi-Fi Alliance (WFA). This provides you to configure the parameters of wireless multimedia; VMM allows wireless communication to define a priority according to the dhome gateway type.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 4.4.4 WDS If or not enable WDS mode 4.4.5 WPS WPS (Wi-Fi Protected Setup) provides easy procedure to make network connection between wireless station and wireless access point (vigor router) with the encryption of WPA and WPA2. It is the simplest way to build connection between wireless network clients and vigor router.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 Field Name WPS Setting Description If or not enable WPS function WPS Display the current status of WPS, including current state, Summary SSSID name, authentication methods, encryption type and the PIN code of this AP. Generate Reset OOB Generate a new PIN code G902 uses default security policy to allow other non-WPS users to access and apply.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 4.4.6 Station Info This page shows user the clients’ information which connects to the AP. 4.4.7 Advanced Field Name Description BG Protection Mode Select G protection mode, options are on, off and automatic. The interval of sending a wireless beacon frame, within this range, it will send a beacon frame for the Beacon Interval information of the surrounding radio network.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 Short Slot Tx Burst Pkt_Aggregate IEEE802.11H support Country Code Wi-Fi Multimedia(WMM) WMM Capable APSD Capable WMM Parameters If or not enable short slot, default is enable, it is helpful in improving the transmission rate of wireless communication. One of the features of MAC layer, it is used to improve the fairness for transmitting TCP.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 4.5 Wireless 5G 4.5.1 Basic Field Name Radio on/off Network Mode Description Select “Radio Off” to disable wireless. Select “Radio on”to enable wireless. Choose one network mode from the drop down list SSID Multiple It is the basic identity of wireless LAN. SSID can be any alphanumeric or a combination of special characters. It will appear in the wireless network access list. G902 supports multiple SSIDs.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 BSSID A group of wireless stations and a WLAN access point (AP) consists of a basic access device (BSS), each computer in the BSS must be configured with the same BSSID, that is, the wireless AP logo. Frequency (Channel) You can select Auto Select and channel HT Physical Mode Operating Mode Channel Bandwidth Guard Interval MCS Reverse Direction （RDG） 1/2/3/4/5/6/7/8/9/10/11. 1.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 4.5.2 Wireless Security Field Name Description SSID Choose one SSID from SSID, Multiple SSID1, Choice Multiple SSID2 and Multiple SSID3. Select an appropriate encryption mode to improve Security Mode the security and privacy of your wireless data packets. Each encryption mode will bring out different web page and ask you to offer additional configuration.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 4.5.6 Station Info Please refer to 4.4.6 section. 4.5.7 Advanced Please refer to 4.4.7 section.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 4.6 SIP 4.6.1 SIP Settings Field Name SIP T1 Max Forward SIP Reg User Agent Name Max Auth Mark All AVT Packets RFC 2543 Call Hold SRTP SRTP Prefer Encryption Service Type NAT Traversal Description The minimum scale of retransmission time Sip packets Max Forward message header fields used to limit the request which jump in his destination .
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 STUN Server Address NAT Refresh Interval STUN Server Port Add the correct STUN service provider IP address. Set NAT Refresh Interval, default is 60s. Set STUN Server Port, default is 5060. 4.6.2 VoIP Qos Field Name Description SIP /RTP QoS The default value is 0,you can set a range of values is 0~63 4.7 FXS1 4.7.1 SIP Account 1.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 Field Name Line Enable Description If or not enable the line. If or not enable PEER to PEER. Peer To Peer If enable, SIP-1 will not send register request to SIP server; but in Status/ SIP Account Status webpage, Status is Registered; lines 1 can dial out, but the external line number cannot dialed line1.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 2. Audio Configuration Field Name Audio Codec Type1 Description Choose the audio codec type from G.711U, G.711A, G.722, G.729, G.723 Audio Codec Type2 Choose the audio codec type from G.711U, G.711A, G.722, G.729, G.723 Audio Codec Type3 Choose the audio codec type from G.711U, G.711A, G.722, G.729, G.723 Audio Codec Type4 Choose the audio codec type from G.711U, G.711A, G.722, G.729, G.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 3. Supplementary Service Subscription Field Name Description Call Waiting If or not enable Call Waiting Hot Line Fill in the hotline number. Pickup handset or press handsfree/headset button, the device will dial out the hotline number automatically. MWI Enable If or not enable MWI (message waiting indicate). If the user needs to user voice mail, please enable this feature.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 4. Advanced Field Name Domain Name Type Description If or not use domain name in the SIP URI. Carry Port Information If or not carry port information in the SIP URI. Signal Port The local port of SIP protocol, default is 5060. DTMF Type Choose the DTMF type from Inbound, RFC2833 and SIP INFO. RFC2833 Payload(>=96) User can use the default setting.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 times fail; the device will no longer detect the primary server. Keep-alive Interval(10-60s) The interval that the device will send an empty packet to proxy. Anonymous Call Anonymous Call Block Proxy DNS Type If or not enable anonymous call. If or not enable anonymous call block. Set the DNS server type, choose from A type and DNS SRV. Use OB Proxy In Dialog Reg Subscribe Enable If or not use OB Proxy In Dialog.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 2. Regional Field Name Description Tone Type Choose tone type form China, US, Hong Kong and so on. Dial Tone Dial Tone Busy Tone Busy Tone Off Hook Warning Tone Off Hook warning tone Ring Back Tone Call Waiting Tone Min Jitter Delay Ring back tone Call waiting tone The Min value of home gateway’s jitter delay, home gateway is an adaptive jitter mechanism.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 3. Features and Call Forward Field Name All Forward Features Busy Forward Description If or not enable forward all calls If or not enable busy forward. Answer If or not enable no answer forward. No Forward All Forward Call Forward Feature Code Set the target phone number for all forward. The device will forward all calls to the phone number immediately when there is an incoming call.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 4. Miscellaneous Field Name Codec Loop Current Impedance Maching CID service CWCID Service Dial Time Out Call Immediately Key ICMP Ping Description Set off-hook loop current, default is 26 Set impedance matching, default is US PBX,Korea,Taiwan(600). If or not enable displaying caller ID; If enable, caller ID is displayed when there is an incoming call or it won’t be displayed. Default is enable. If or not enable CWCID.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 4.7.3 Dial Plan 1. Parameters and Settings Field Name Dial Plan Line Digit Map Action Move Up Move Down Description If or not enable dial plan. Set the line. Fill in the sequence used to match input number The syntactic, please refer to the following Dial Plan Syntactic Choose the dial plan mode from Deny and Dial Out. Deny means G902 will reject the matched number, while Dial Out means G902 will dial out the matched number.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 2. Adding one dial plan: Step 1. Enable Dial Plan Step 2. Click Add button, and the configuration table Step 3. Fill in the value of parameters. Step 4.Press OK button to end configuration. Step 5. Press Save button to save changes 3. Dial Plan Syntactic No. 1 String 0123456789*# 2 x 3 [sequence] 4 x.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 4.7.4 Blacklist In this page, user can upload or download blacklist file, and can add or delete or edit blacklist one by one. Click to select the blacklist file and click upload it to G902; Click to to save the blacklist file to your local computer. Select one contact and click edit to change the information, click delete to delete the contact, click Move to phonebook to move the contact to phonebook.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 4.8 FXS2 The settings of FXS2 are the same as FXS1. 4.9 Security 4.9.1 Filtering Setting Field Name Filtering Default Policy Mac address Dest IP address Source IP address Protocol Description If or not enable filter function Choose to give up or accept Add the Mac address filtering Dest IP address Source IP address Select a protocol name, support for TCP, UDP and TCP&UDP Dest.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 4.9.2 Content Filtering Field Name Description Filtering Default Policy If or not enable content Filtering The default policy is to accept or to prohibit filtering rules List the URL filtering rules that already existed (blacklist) Current Webs URL Filters Delete/Cancel You can choose to delete or cancel the existing filter rules Add a URL Filter Add URL filtering rules Add/Cancel Click adds to add one rule or click cancel.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 4.10 Application 4.10.1 UPnP UPnP (Universal Plug and Play) support zero setting networking, and can automatically discover a variety of networked devices. UPnP is enabled, allows the device supports UPnP function dynamically access network, obtain an IP address, and convey its performance information. If the network has a DHCP and DNS server, you can automatically obtain DHCP and DNS services.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 4.10.3 MLD Field Name MLD enable Description If or not enable MLD function 4.11 Storage 4.11.1 Disk Management This page is used to manage the USB storage device.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 4.11.2 FTP Setting Field Name Description FTP Server If or not enable FTP server FTP Server Name Set the FTP server name Anonymous Login If or not support anonymous login FTP Port Max.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 4.12 Administration Use can manage the device in these webpage; you can configure the Time/Date, password, web access, system log and associated configuration TR069 4.12.1 Management You can configure the value of Time/Date, password, web access, and system log and so on. 1.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 3. NTP settings Field Name Description NTP Enable If or not enable NTP Current Time Display current time NTP Settings Setting the Time Zone Primary NTP Server Primary NTP server's IP address or domain name Secondary NTP Server Options for NTP server's IP address or domain name NTP synchronization NTP synchronization cycle, cycle time can be 1 to 1440 minutes in any one, the default setting is 60 minutes 4.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 Field Name Syslog Enable Syslog Level Description If or not enable syslog function Select the system log, there is INFO and Debug two grades, the Debug INFO can provide more information. 6. Factory Defaults Setting Remote Syslog Enable If or not enable remote syslog function. Remote Syslog server Add a remote server IP address. If enable this function ,the device will not be restore factory settings 7.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 4.12.2 Firmware Upgrade 1. Choose upgrade file type from Image File and Dial Rule 2. Press 3. Press to browser file. to start upgrading. 4.12.3 Provision Provisioning allows G902 auto-upgrading and auto-configuring, and Flyingvoice devices support TFTP, HTTP and HTTPs three ways. 1. Before testing or using TFTP, user should have tftp server and upgrading file and configuring file. 2.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 G902 will forced to resync. If or not enable firmware upgrade after resync, by default it is enabled. If or not enable resync from SIP. It is used for In-house provision mode only. When use TFTP with option 66 to realize provisioning, user must input right configuration file name in IP542N's webpage. When disable Option 66, this parameter has no effect. It is used for In-house provision mode only.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 4.12.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 4.12.6 Diagnoisis In this page, user can do ping test and traceroute test to diagnose the device’s connection status. 1. Ping Test Enter the destination IP or host name, and then click Apply, device will perform ping test. 2. Traceroute Test Enter the destination IP or host name, and then click Apply, device will perform traceroute test. 4.12.7 Operation Mode Choose the Operation Mode as Basic Mode or Advance Mode.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 4.13 System Log If you enable the system log in Status/syslog webpage, you can view the system log in this webpage. 4.14 Logout Press the logout button to logout, and then the login window will appear.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 4.15 Reboot Press the button to reboot G902.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 5 Trouble shooting of the guide 5.1 Setting your PC gets IP automatically Following are the process of setting your PC gets IP automatically Step 1.Click the “begin” Step 2.Select “control panel”, then double click “network connections” in the “control panel” Step 3.Right clicks the “network connection” that your PC uses, select “attribute” and you can see the interface as picture 1: Step 4.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 5.2 Can not connect to the configuration Website Solution: Check if the Ethernet cable is properly connected, then Check if the URL is right wrote, the format of URL is: http:// the IP address: 8080, 8080 must be added, then Check if the version of IE is IE8, or use other browser such as Firefox or Mozilla, then Contact your administrator, supplier, or ITSP for more information or assistance. 5.
Copy Right 2014 All Rights Reserved by FLYINGVOICE TECHNOLOG LIMITED V1.1 Step 3: Please Login from WAN port. Under is example of Page Status->Basic.
