TIO RMA N NFO I T TA N se R nce O e P r u e f e M r I efo re re b u t d u a f Re n for i a t e &r For all customer enquiries or for replacement parts, contact:Australia New Zealand Phone: 1800 802 831 Email: customer.service@husqvarna.com.au Phone: (09) 920 2410 Email: sales@hopnz.co.
Carton Contents Switch Handle Steady Handle Tube Trimmer Head Instruction Manual Guard Electric Cable with moulded on plug Wheel IMPORTANT ! Please check the contents of the carton are correct BEFORE assembling your new Flymo product.
. Do not use the trimmer if the electric cables are damaged or worn. 4. Immediately disconnect from the mains electricity supply if the cable is cut, or the insulation is damaged. Do not touch the electric cable until the electrical supply has been disconnected. Do not repair a cut or damaged cable. Replace it with a new one. 5. Your extension cable must be uncoiled, coiled cables can overheat and reduce the efficiency of your trimmer. 6. Keep the cable clear of the cutting area and obstacles at all times.
Assembly Instructions A1 B1 C1 Assembly of Switch Handle to Tube (A1) • Ensure that the internal cable is not twisted. 1. Insert the tube into the switch handle. 2. Push until it clicks into position. • ENSURE THAT THE TUBE IS FULLY LOCATED BY ATTEMPTING TO REMOVE IT. A2 Assembly of Trimmer Head to Tube (A2) • Ensure that the internal cable is not twisted. 1. Insert the tube into the trimmer head. 2. Push until it clicks into position.
How to trim and edge H J • • • • K L WARNING The use of eye protection is recommended. Do not lean over the trimmer whilst trimming or edging, objects may be thrown by the cutting line. Do not allow cutting head to rest on the ground. Do not overload your trimmer. Overloading can be avoided by making sure the motor speed does not drop unduly. DISCONNECT FROM THE MAINS ELECTRICITY SUPPLY BEFORE ATTEMPTING ANY MAINTENANCE OR ADJUSTMENT. BEFORE USE Make sure that both lines are fed out.
Cutting Head P To remove spool cap 1. Press and hold in the two cap release latches. (P). 2. Pull cap away from the spoolholder. (P). When refitting the spool cap 1. Keep all areas of the cap and spoolholder clean. Failure to do so may prevent the cap being securely located in the spoolholder. 2. Replace the cap, pressing firmly DOWN towards the spoolholder to ensure cap is fully located. 3. Check that the cap is correctly fitted by trying to remove it without depressing the two latches.
Maintenance S • WARNING Disconnect from the mains electricity supply, before attempting any maintenance or adjustment. Cutting head continues to rotate after the trimmer has been switched off. Keep fingers and hands clear of the line cutter on leading edge of guard. Caring for your Contour Power Plus After you have finished using your Flymo Contour Power Plus follow the procedure below: AVOID ACCIDENTAL STARTING.
Fault Finding Chart WARNING Disconnect from the mains electricity supply before attempting any maintenance or adjustment. FAULT LINE NOT FEEDING OR LINE TOO SHORT OR TRIMMER VIBRATES CONTINUOUS CLATTERING NOISE LINE SNAPS CONTINUOUSLY CHECK ACTION Is the automatic line feed working? No Manually feed out line. SEE “MANUAL LINE FEED” Is the line fed out and visible? Has line been removed from cleat? No Remove cap and spool, free line and re-fit spool and cap.
EC Declaration of Conformity I, the undersigned M. Bowden of Husqvarna Outdoor Products, Aycliffe Industrial Park, NEWTON AYCLIFFE, Co. Durham. DL5 6UP. Certify that the product:Category........ Electric Lawn Trimmer Make.............. Husqvarna Outdoor Products Conforms to the specifications of Directive 2000/14/EC I, the undersigned M. Bowden of Husqvarna I, the undersigned M. Bowden of Husqvarna Outdoor Products, Aycliffe Industrial Park, Outdoor Products, Aycliffe Industrial Park, NEWTON AYCLIFFE, Co.