User's Manual

ManualsBrandsFLYSKY RC MODEL TECHNOLOGY ManualsElectronics3CH Gun Radio

Table Of Contents

7. Transmitter specifications

发射机参数

SPECIFICATIONS：

MODEL: FS-A3

8.Receiver specifications

接收机参数

机种参数：

RED I3

Transmitter specifications:

机种参数

通道个数：2

适合机种：车/船

频率范围：2.405-2.475GHz

波段宽度：500KHz

波段个数：142个

发射机功率：不高于18dBm

2.4G模式：第二代增强版自动跳频数字系统(含第一代系统）

编码方式：GFSK

通道分辨率：1024级

低电压报警：低于4.2V时

数据输出：Micro-USB PPM

方向盘转动角度：45度（前35度，后15度）

充电接口：无

天线长度：26毫米

机身重量：323克

输入电源：6V DC 1.5AA*4

显示方式：LED指示灯

外形尺寸：150*80*196毫米

外观颜色：黑色

Channels: 3

Model type: car/boat

RF range: 2.405-2.475GHz

Bandwidth: 500KHz

Band sum: 142

RF.receiver sensitivity: -105dBm

2.4G system: AFHDS 2A

Code type: GFSK

Sensitivity: 1024

Power: 4.0-6.5V DC

ANT lenght: 26mm

Weight: 5g

Size: 35*22*12mm

Color: black

Certificate: CE FCC

通道个数：3

适合机种：车/船

频率范围: 2.405-2.475GHz

波段宽度： 500KHz

波段个数： 142个

接收灵敏度： -105dBm

2.4G模式：第二代增强版自动跳频数字

系统

编码方式： GFSK

通道分辨率： 1024级

输入电源： 4.0-6.5V DC

天线长度： 26毫米

机身重量： 5克

外形尺寸： 35*22*12毫米

外观颜色：黑色

认证： CE FCC

Digital propotional radio control system

RED I3

Channels: 2

Model type: car/boat

RF range:2.405-2.475GHz

Bandwidth:500KHz

Band:142

RF power: less than18 dBm

2.4G system: AFHDS2A and AFHDS

Code type: GFSK

Sensitivity: 1024

Low voltage warning: less than 4.2V

DSC port: Micro-USB PPM

ST range:70 L:35 R:35

TH range:45 F:35 B:15

Charger port: no

ANT length: 26mm

Weight: 323g

Power: 6V DC 1.5AA*4

Display mode:LED indicator

Size: 150*80*196mm

Color: blacK

Summary of content (8 pages)

PAGE 1
Digital propotional radio control system RED I3 7. Transmitter specifications 发射机参数 Transmitter specifications: Channels: 2 Model type: car/boat RF range:2.405-2.475GHz Bandwidth:500KHz Band:142 RF power: less than18 dBm 2.4G system: AFHDS2A and AFHDS Code type: GFSK Sensitivity: 1024 Low voltage warning: less than 4.2V DSC port: Micro-USB PPM ST range:70 L:35 R:35 TH range:45 F:35 B:15 Charger port: no ANT length: 26mm Weight: 323g Power: 6V DC 1.
PAGE 2
9.Receiver and servo connections 接收机与伺服器连接 9.01. Installation when a motor controller is used 带马达模型的安装连接调速器开关伺服器马达电池接收机 Remark: Place the receiver antenna upright and perpendicular to the horizontal plane Keep the receiver antenna away from any metal objects to ensure max sensitivity.
PAGE 3
Digital propotional radio control system RED I3 9.02. Installation for gas powered models 开关发动机模型的安装电池油门接收机方向系统伺服器 9.03. Suggestions for RX fail safe setting. 接收机防失控设置建议 1 设定在扣机的中间，适合电车使用。 2 设定在刹车位置，适合油车使用。 1 It is set in the middle of the trigger, which fits the electric vehicle. 2 It is set in brake, which fits the gas vehicle.
PAGE 4
10. 2.4GHz Operation notes 10.01. Matching(code)/Binding 2.4G操作注意事项对码 All receivers are already paired with their respective transmitter during production. If you wish to bind it with another transmitter, please follow the instructions below. Remark: FS - brand system are not compatible with other brands Steps: 1. Ensure you are using AFHDS2A system 2. Correctly install the battery inside 2.4G transmitter w/o powering it on. 3. Insert the binding plug into the BIND channel slot on the receiver. (Figure.
PAGE 5
Digital propotional radio control system RED I3 10.02 Power on 开机 A. Connect every part. B. Switch on the power supply of the transmitter. C. Connect the power supply of the receiuer. D. Receive LED light solid. E. Finish and use. 1. 将各部件链接好； 2. 打开发射机电源开关； 3. 连通接收机电源； 4.接收机LED恒亮； 5.使用。 Tx power ON 10.3 Shut down Rx power ON 关机 A. Connect every part. B. Cut off the transmitter power supply. Rx power off 1. 关闭接收机的电源； 2.
PAGE 6
11. each part of the transmitter 发射机部件 Front 10 11 2 6 8 4 9 5 12 13 1 3 1 对码键 BIND Key 2 电源指示灯 POWER LED 3 Ch1倒置开关 CH1 REV 4 电源开关 POWER ON/OFF 5 充电指示灯 LED 6 Ch1 中位微调 CH1 TRIM 7 Ch2 倒置开关 CH2 REV 7 14 8 Ch2 中位微调 CH2 TRIM 10 工作指示灯 POWER CHECK 11 Ch2比例微调 CH2,M,P 13 油门扳机THROTTLE TRIGGER 14 电池盒 BAT BOX 9 12 Ch1通道比例微调 CH1 D/R 方向调轮 STEERING WHEEL 油门比例微调TH,M,P On some model, the travel of the throttle is not equal to the travel of the brakes.
PAGE 7
Digital propotional radio control system RED I3 13. Fail safefunction 13.01 Failsafe Instruction 接收机操作说明失控保护功能说明 FAIL SAFE FUNCTION 1.Function Failsafe aims to prevent out- of- control driving of RC car orRC boat. If the Receiver is not able to receive any signal, from the control to throttle, the parameter of throttle on receiver will turn back to its original setting. 2. Setting a. Turn on the Transmitter switch; b. Turn on the Receiver switch. the LEDwill be lighting; c.
PAGE 8
FCC Statement 声明 FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.