User's Manual

ManualsBrandsFLYTECH ManualsElectronicsPOS

USER MANUAL

VERSION 1.0 September 2019

POS667

Hardware System

Summary of content (29 pages)

PAGE 1
USER MANUAL VERSION 1.
PAGE 2
Copyright 2019 All Rights Reserved Manual Version 1.0 The information contained in this document is subject to change without notice. We make no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. We shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
PAGE 3
CE MARK This device complies with the requirements of the EEC directive 2014/30/EU with regard to “Electromagnetic compatibility” and 2014/35/EU “Low Voltage Directive”. FCC This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation.
PAGE 4
LEGISLATION AND WEEE SYMBOL 2012/19/EU Waste Electrical and Electronic Equipment Directive on the treatment, collection, recycling and disposal of electric and electronic devices and their components. The crossed dust bin symbol on the device means that it should not be disposed of with other household wastes at the end of its working life. Instead, the device should be taken to the waste collection centers for activation of the treatment, collection, recycling and disposal procedure.
PAGE 5
Revision History Changes to the original user manual are listed below: Revision 1.
PAGE 6
Table of Contents 1. Packing List .................................. 1 1-1. Standard Accessories .....................................................1 1-2. Optional Accessories.......................................................2 2. System View.................................. 3 2-1. 2-2. 2-3. 2-4. Front & Side View ............................................................3 Rear View .........................................................................3 IO Ports View..........................
PAGE 7
6SHFLÀFDWLRQ ................................ 15 &RQÀJXUDWLRQ ............................... 17 6-1. D84U Motherboard Layout ............................................17 6-2. Connectors & Functions ................................................18 6-3. Jumper Setting ...............................................................
PAGE 8
The page is intentionally left blank.
PAGE 9
1. 1-1. Packing List Standard Accessories a b c d a. b. c. d. System Power adapter (90W) Power cord RJ45-DB9 cable (x2) Note: Power cord will be supplied differently according to various region or country.
PAGE 10
1-2. Optional Accessories a b c d e f g h i a. b. c. d. e. f. g. h. i. 2 MSR module iButton module NFC module Customer display Hinge cover for customer display 10.
PAGE 11
2. 2-1. System View Front & Side View 1 4 5 6 7 7 23 No. 1 2 3 4 5 6 7 2-2. Description Touch screen USB2.0 Power button Hinge cover Stand arm Stand arm cover Stand front cover Rear View 1 1 2 No.
PAGE 12
2-3. IO Ports View a b c d No. a b c d e f g h 2-4. e f g Description FeDP LAN DC 19V in USB 2.0 x 2 USB Type C x 2 USB 3.0 x 2 COM x 2 Cash drawer System Dimensions 374.7 mm 375.
PAGE 13
3. 3-1. System Assembly & Disassembly Install the Power Adapter The system is equipped with a 90W power adapter. Please plug it into the system as shown below. 1. Find the DC-in connector located on the bottom of the system.(refer to Chapter 2-3 c). 2. Plug the cable directly into the connector then plug the adapter directly into the AC outlet. 3-2. Remove the System Box 1. Lay down the system to access the bottom of the stand. 2. Remove the screws (x2) and pull the holder of the system box outwards.
PAGE 14
3. Disconnect the cable of the LCD panel. 4. The system box is placed onto four hooks. Lift the system box and then pull it outwards to release it from the bottom of the stand.
PAGE 15
4. 4-1. Peripherals Installation Install the MSR Module 1. Press to remove the dummy cover and then loosen the screws (x2). 2. Position the MSR module and fasten the screws (x2) on the back to secure the module. 3. Attach the top cover of the MSR module and make sure it locks in place.
PAGE 16
4-2. Install the iButton Module 1. Press to remove the dummy cover and then loosen the screws (x2). 2. Position the iButton module and fasten the screws (x2) on the back to secure the module. 3. Attach the top cover of the iButton module and make sure it locks in place.
PAGE 17
4-3. Install the NFC Module 1. Press to remove the dummy cover and then loosen the screws (x2). 2. Position the NFC module and fasten the screws (x2) on the back to secure the module. 3. Attach the top cover of the NFC module and make sure it locks in place.
PAGE 18
4-4. Install the Customer Display 1 2 2 1 1. To install the customer display, replace the hinge cover with the one which has a opening in the top. Removing the hinge cover: The cover attaches magnetically to the hinge. Pull the WRS VLGH RI WKH FRYHU RXUGZDUGV ÀUVW DQG WKHQ UHOHDVH WKH UHVW SDUW RI WKH FRYHU WR seperate it from the hinge.
PAGE 19
4-5. Install the Second Display Accessories items a. b. c. d. e. f. g. 10.1" 2nd display module Top arm cover Bottom arm cover Hinge cover Screws for 2nd display arm x 5 Screws for top arm cover x 4 Screws for bottom arm cover x 2 a d b e c f g 1. Remove the stand cover by pulling it upwards. 2. Attach the 10.1" 2nd display module to the system and route the 2nd display cable through the hole of the stand as picture shown. 3. Fasten the 2nd display module in place with the screws (x5) provided.
PAGE 20
5. Secure the top arm cover by fastening the screws (x4) from underneath. 6. Attach the bottom arm covers (x2) and fasten the screws (x2). 7. Follow steps 1 and 2 described in Chapter 3-2 to release the holder of the system box. Thread the 2nd display cable through the opening and connect the host end of the cable to FeDP port. (refer to Chapter 2-3 a). 8. Finally attach the hinge cover.
PAGE 21
4-6. Cash Drawer Installation You can install a cash drawer through the cash drawer port. Please verify the pin assignment before installation. Cash Drawer Pin Assignment Pin 1 2 3 4 5 6 1 6 Signal Cash drawer 2 In Cash drawer 1 Out Cash drawer 1 In 12V / 19V Cash drawer 2 Out GND Cash Drawer Controller Register The Cash Drawer Controller use one I/O addresses to control the Cash Drawer.
PAGE 22
Bit 7: Reserved Bit 6: Reserved Bit 5: Reserved Bit 4: Cash Drawer 1 pin output control. = 1: Opening the Cash Drawer = 0: Allow close the Cash Drawer Bit 3: Cash Drawer 1 pin input control. = 1: the Cash Drawer closed or no Cash Drawer = 0: the Cash Drawer opened Bit 2: Reserved Bit 1: Reserved Bit 0: Reserved Note: Please follow the Cash Drawer control signal design to control the Cash Drawer. Cash Drawer Control Command Example Use Debug.
PAGE 23
5. 6SHFLÀFDWLRQ Model Name Mainboard CPU support POS667 D84U Intel KabyLake-U CPU i3 7100U 2.4GHz System memory 1x DDR4 2133MHz SO-DIMM up to 16GB Graphic memory LCD Touch Panel LCD size ,QWHO +' *UDSKLF '; GHÀQH RQ &38 15.6” LED Brightness (cd/m²) 3000 nits Maximal resolution 1920 x 1080 Touch screen type Storage FlashMemory I/O Ports True-Flat PCAP Touch 2x M.2 (M-key) NVMe or M.2 SATA SSD module USB Type C [ )O\WHFK GHÀQHG PLQL '3 (2-lane eDP/USB2.
PAGE 24
Model Name Mainboard Control/Indicator Power button POS667 D84U 1 Power LED &HUWLÀFDWH EMC & Safety 1(turn on: blue / turn off: Amber) ESD Environment Sealing 4 kV Contact discharge, 8 kV Air discharge Operating temperature Storage temperature Humidity Dimension (W x D x H) Weight OS supported FCC, Class A, CE, LVD IP54 (front side) 0°C ~ 35°C (32°F ~ 95°F) -20°C ~ 60°C (-4°F ~ 140°F) 20% ~ 85% RH non-condensing 375.8 x 200.0 x 374.7 mm (14.8" x 7.9" x 14.
PAGE 25
D84U Motherboard Layout 6-1. &RQÀJXUDWLRQ 6.
PAGE 26
6-2. Connectors & Functions Connector CN1 CN2 CN3 CN4/11 CN5 CN6 CN7 CN9/CN10/CN12/CN14 CN16 CN17 CN18 CN20 PWR1/PWR2 RJ11_1 RJ45_1 SW1/SW2 DIMM_A1 FAN1 FeDP1 FeDP2 USB1/USB4/USB5 USB2/USB3 USB7 USB8 COM1/COM2 COM3 MINI_PCIE1 JP1 JP3 JP4 JP5JP5(1-2)(3-4) JP5(5-6) 18 Function EC Debug SATA power connector M.2 E-KEY WIFI connector M.
PAGE 27
6-3. Jumper Setting Audio Line-out Setting Function ɺ6WHUHR Reserved (line-out) JP1 1 2 1 2 Cash Drawer Power Setting Function JP3 ɺ 9 1 3 2 4 9 1 3 2 4 Speaker watt setting Function JP5 ɺ : 1 3 5 2 4 6 3W 1 3 5 2 4 6 Speaker cable setting Function JP5 ɺ / P 1 3 2 4 L=2.
PAGE 28
LCD ID Setting Panel# Resolution LVDS Output Bits Channel Interface 1 800 x 600 18 Single LVDS Panel 1 3 5 7 9 2 4 6 8 10 2 800 x 600 24 Single LVDS Panel 1 3 5 7 9 2 4 6 8 10 3 1024 x 768 18 Single LVDS Panel 1 3 5 7 9 2 4 6 8 10 4 1024 x 768 24 Single LVDS Panel 1 3 5 7 9 2 4 6 8 10 5 1366 x 768 18 Single LVDS Panel 1 3 5 7 9 2 4 6 8 10 6 1366 x 768 24 Single LVDS Panel 1 3 5 7 9 2 4 6 8 10 7 1024 x 600 18 Single LVDS Panel 1 3 5 7 9 2 4 6 8 10 8 1280 x 1024
PAGE 29
COM1/COM2 Power Setting COM1, COM2 can be set to provide power to your serial device. 7KH YROWDJH FDQ EH VHW WR 9 RU 9 LQ WKH %,26 1. Power on the system, and press the key when the system is booting up to enter the BIOS Setup utility. 2. Select the Advanced tab. 3. Select 9*$ &20 3RZHU &RQÀJXUDWLRQ Ports and press to go to display the available options. 4. To enable the power, select COM1 ,COM2 Power setting and press . Select Power and press .