Manual

3
ADDITIONAL ITEMS REQUIRED
Radio Control System
The Sensei Rx-R (Receiver Ready) comes with the servos
installed, so all that is required is a 6-channel transmitter
and receiver. The Tactic
™
TTX600 2.4GHz spread spectrum
6-channel radio control system (TACJ2600) is included with
the RTF (ready to fl y) version of the Sensei, so this same
radio system is ideal for your Rx-R version, too.
❍ Tactic TTX600 2.4GHz 6-channel system (TACJ2600)
❍ (4) AA batteries will be required to operate the
recommended transmitter (FUGP7308).
Battery and Charger
The Sensei RTF comes complete with a motor battery and
charger. The Sensei Rx-R version requires a 2100mAh 11.1V
LiPo battery and LiPo Charger. The Sensei was designed for
the Flyzone 2100mAh 11.1V LiPo battery (HCAP6387). Other
LiPo batteries similar in size with the same voltage and capacity
may also work, but they may not fi t properly in the battery
compartment or have the same type of battery connector. In
addition to a battery, a LiPo battery charger is also required and
there are several that will work (depending on your budget and
requirements). A safe, economical charger is the ElectriFly
®
3S
(3-cell/ 11.1V) LiPo Smart Charger (GPMM3318). The Smart
Charger includes adapters to charge from a 110V wall outlet
or a 12V DC outlet from a car. The Smart Charger will take
approximately 4-1/2 hours to fully charge the battery. Some
pilots prefer to have several batteries and charge them faster
so they can fl y more. For charging up to four batteries faster at
the same time, the Great Planes PolyCharge4
™
DC-powered
LiPo charger (GPMM3015) is recommended. But unlike the
Smart Charger, the PolyCharge4 does not have an internal
LiPo cell balancer which is a critical component in making sure
your LiPo batteries charge effi ciently and evenly. So, for each
LiPo battery you wish to charge simultaneously, one Great
Planes Equinox
™
LiPo Cell Balancer (GPMM3160) will also be
required. Finally, the PolyCharge4 does not have AC capability,
so if wall charging is a priority, a separate AC 12-Volt power
source must also be purchased separately. A suitable power
supply for the PolyCharge4 is the Great Planes 12V 12A DC
power supply (GPMP0901)
.
Required Assembly Tool
Other than common hobby tools this is the list of building
supplies that are required to fi nish the Sensei.
❍ Small needle-nose pliers (HCAR0625) or hemostats
(SQUR2502)
❍ #1 Phillips screwdriver (DTXR0174)
❍ Small crescent wrench
❍ Great Planes stick-on lead weight (Optional, GPMQ4485)
ORDERING REPLACEMENT PARTS
Replacement parts for the Hobbico Flyzone Sensei are
available using the order numbers in the Replacement Parts
List that follows. The fastest, most economical service can
be provided by your hobby dealer or mail-order company.
To locate a hobby dealer, visit the Hobbico web site at www.
hobbico.com. Choose “Where to Buy” at the bottom of the menu
on the left side of the page. Follow the instructions provided on
the page to locate a U.S., Canadian or International dealer.
Parts may also be ordered directly from Hobby Services by
calling [phone], or fax at [phone], but full
retail prices and shipping and handling charges will apply.
Illinois and Nevada residents will also be charged sales tax.
If ordering via fax, include a Visa
®
or MasterCard
®
number
and expiration date for payment.
Mail parts orders Hobby Services
and payments by 3002 N Apollo Drive, Suite 1
personal check to: Champaign IL 61822
Be certain to specify the order number exactly as listed in the
Replacement Parts List. Payment by credit card or personal
check only; no C.O.D.
If additional assistance is required for any reason, contact
Product Support by telephone at [phone], or by e-mail
at [e-mail].
REPLACEMENT PARTS LIST
ORDER NO.
HCAA6380
HCAA6381
HCAA6382
HCAA6383
HCAA6384
HCAA6385
HCAA6386
HCAA6387
HCAA6388
HCAA6389
HCAA6390
HCAA6391
DESCRIPTION
Fuselage
Wing Set
Stab/Elevator Set
Vertical Fin
Main Gear
Nose Gear
ESC
LiPo Battery 2100mAh
Brushless Motor
Spinner
Propeller 10x5
Decal Set