2000MM Beaver DHC-2 REALISTIC FLAPS INSTALLED RIGID STRONG DURABLE EPO STABLE SMOOTH FLYING PERFORMANCE FMSMODEL.
Table of Contents Introductions ··························································································································3 Contents of Kit ························································································································4 Assembling the Plane ···············································································································5 Battery and radio installation······················································
Wingspan: 2000mm (78.7in) Overall Length: 1304mm (51.3in) Flying Weight: Around 3800g (134oz) Motor Size: Brushless 4258-KV550 Wing Load: 71.1 g/dm² (0.16oz/in²) Wing Area: 53.4 dm² ( sq.in) ESC: 70A Servo: 6g Servo x 17 Contents of Kit Before assembly, please inspect the contents of the kit. The photo below details the contents of the kit and labels.
Horizontal Tail Installation 1.Slide the horizontal tail tube into the hole in rear of the fuselage 2.Install the 2 pieceleft and righthorizontal tail as shown. Ensure the control horn faces down. 3.Install 4 screws in the front and rear holes in the button of the horizontal tail. 4.Attach the ball link to the elevator control horn’s outermost hole using the included nut and screw. HKM3.0×10mm fig2 fig2 fig1 fig1 fig3 5. Carefully apply CA to the base and side of the rear Horizontal stabilizer 6.
Vertical Stabilizer Installation 1. Connect the rudder and elevator servo connectors to the servo extensions in the fuselage. 2. Slide the vertical tail assembly into the slot in the fuselage. CAUTION: DO NOT crush or damage the wiring when attaching the vertical tail assembly to the fuselage. 3. Secure the assembly to the fuselage using 2 screws as shown. Long screw in front hole, shorter screw in rear hole. CAUTION:Make sure the screw is tight enough, or it may cause a crash.
Wing Installation 1. Slide the tube into the fuselage then install both wings over the wing tube and into the wing slot of the fuselage. Notice: The connectors on both side should be attached precisely and firmly. fig10 fig11 2. Install the 2 wing struts on the fuselage mount using 2 R-clips. Make sure it is installed precisely.
3.Secure the wings on the fuselage using 4 screws in the top of the wings. Make sure it is tightened enough. HKM3.0×26mm fig15 Removal We recommend removing the wings from the fuselage for storage or transport of the aircraft. 1. Carefully apply CA to the base and side of the front main wing 2. Carefully place the Vortex Generator into the pocket Required Adhesives: Foam Safe Medium CA fig16 1. Carefully apply CA to the base and side of the air speed pocket. 2.
Optional Towing Retract Installation 1.Install the retract to the top of fuselage with four screws as photo shows. 2.Install the cover on the retract with two screws. PA2.6×10mm fig19 fig20 fig20 fig21 KA2.0×10mm PA2.6×26mm KA2.
Optional Float Installation 1. Install the strut bar to both sides of the float. The front bar is longer with 422mm length, the rear bar is shorter with 412mm length. Wrong installation will cause difficulty landing and taking off (fig.24) 422mm 412mm fig23 2.Install the float strut to the float with 8 screws as picture shows. (fig26) HKM3.0×26mm fig24 3.With the fuselage bottom facing up, carefully install the float set to the fuselage with 6 screws. HKM3.
4.Connect the float rudder servo connector then tighten it on the strut with included cable ties. Note: use the Scotch tape on the connector location to avoid the water inflow after connecting.
Battery and radio installation fig28 fig28 Connectors Diagram SERVO LANDING GEAR LED BLACK BLACK SERVO LANDING GEAR LED CAUTION:When connecting the single plug, make sure the positive and negative terminals are in the right direction. An incorrect connection will burn the electronic equipment.
Get your model ready to fly Important ESC and model information 1. The ESC included with the model has a safe start. If the motor battery is connected to the ESC and the throttle stick is not in the low throttle or off position, the motor will not start until the throttle stick is moved to the low throttle or off position. Once the throttle stick is moved to the low throttle or off position, the motor will emit a series of beeps.
Check the control throws The suggested control throw setting for FMS MODEL are as follows (dual rate setting): 16 24 16 10 20 12 Tips: On first flight, fly the model in low rate. The first time you use high rates, be sure to fly at low to medium speeds. High rate, as listed, is only for EXTREME maneuvering. Check the motor rotating direction The motor should rotate clockwise when viewing the plane from the rear.
Install the propeller and spinner Assemble the spinner and propeller as shown below.
Check the C.G. (Center of Gravity) When balancing your model, adjust the motor battery as necessary so the model is level or slightly nose down. This is the correct balance point for your model. After the first flights, the CG position can be adjusted for your personal preference. 1. The recommended Center of Gravity (CG) location for your model is (70-75mm) forward from the leading edge of the main wing (as shown) with the battery pack installed. Mark the location of the CG on top of the wing. 2.
Before flying the model Find a suitable flying site Find a flying site clear of buildings, trees, power lines and other obstructions. Until you know how much area will be required and have mastered flying your plane in confined spaces, choose a site which is at least the size of two to three football fields - a flying field specifically for R/C planes is best. Never fly near people especially children, who can wander unpredictably.
Flying course Take off While applying power, slowly steer to keep the model straight. The model should accelerate quickly. As the model gains flight speed you will want to climb at a steady and even rate. The Beaver will climb out at a nice angle of attack (AOA). Flying Always choose a wide-open space for flying your plane. It is ideal for you to fly at a sanctioned flying field. If you are not flying at an approved site always avoid flying near houses, trees, wires and buildings.
Troubleshooting 19
Spare parts list content FMSPQ101 FMSPQ102 FMSPQ103 FMSPQ104 FMSPQ105 FMSPQ106 FMSPQ107 FMSPQ108 FMSPQ109 FMSPQ110 FMSPQ111 FMSPQ112 FMSPQ113 FMSPQ114 FMSPQ115 FMSPQ116 FMSPQ117 FMSPQ118 FMSPQ119 FMSFLT002 FMSFLT003 FMSPROP035 FMSBM029 FMSDJ014 FMSDZ005 FMSKV550 PRESC003 FMSSER17MGD FMSCON003 FMSRE015 Fuselage Main Wing Set Horizontal Stabilizer Vertical Stabilizer Battery Hatch Antenna Foam Cover Cowl Spinner Engine Vortex Generator Airspeed Head Set Antenna Servo Cover Main Landing Gear Set Wing Strut Se
ESC instruction 21
