70mm Avanti V3 Instruction Manual Bedienungsanleitung Manuel d’utilisation 操作手册 POWERFUL STABLE RIGID 80A power system Smooth flying performance Strong durable EPO material FMSMODEL.
EN WARNING WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to the product,personal property and cause serious injury. This is a sophisticated hobby product and NOT a toy. It must be operated with caution and common sense and failure to do so could result in injury or damage to the product or other property.
EN Introduction Features: • Power system: 70mm 12 bladed EDF, 3060 KV1900 motor, Hobbywing OEM 80A ESC, 9g metal servo The classic FMS Avanti, reimagined! Developed by a Sino-Italian team of pilots and engineers, the FMS Avanti is at the pinnacle of model aviation. The sleek and attractive design from the Sebart team, combined with FMS’ innovative and advanced production methods promises excellent performance from a true head-turning aircraft.
EN Model assembly Main wing installation 1.Install the wing spar through the fuselage pass-through as shown. 2. Slide the wing halves onto the wing spar. HKM3.0*16mm 3. Use the included screws to secure the wing halves to the fuselage.
EN Model assembly Wing fence installation 1.Install the wing fences onto the wings as shown. Secure with foam-safe CA. Required Adhesives: Foam Safe Medium CA Horizontal and vertical stabilizer installation 1. Install the horizontal stabilizer onto the fuselage and connect the elevator servo leads as shown. HKM3.0*16mm 2. Secure the horizontal stabilizer using the included screws.
EN Model assembly 3. Install the vertical stabilizer into the fuselage slot and connect the rudder servo lead. HKM3.0*16mm 4. Secure the vertical stabilizer using the included screws.
EN Battery installation 1.Pull back on the latch and remove the battery hatch. 2.Apply the hook tape to the cable end of the battery. 3.Slide the full charged battery into the battery compartment with the power supply cable toward the rear end of the plane. Note: The center of gravity can be adjusted by moving the battery forward or aft.Having the correct center of gravity is critical to achieving proper flight characteristics.
EN Transmitter and model setup Bank left Aileron Before getting started, bind your receiver with your transmitter. Please refer to your transmitter manual for proper operation. CAUTION: To prevent personal injury, DO NOT install the propeller assembly onto the motor shaft while testing the control surfaces. DO NOT arm the ESC and do not turn on the transmitter until the Transmitter Manual instructs you to do so.
EN Clevis installation 1.Pull the tube from the clevis to the linkage. 2.Carefully spread the clevis, then insert the clevis pin into the desired hole in the control horn. 3.Move the tube to hold the clevis on the control horn. a. d. b. e. c. f. Control horn and servo arm settings The table shows the factory settings for the control horns and servo arms. Fly the aircraft at the factory settings before making changes.
EN Before flying the model Flying course Find a suitable flying site Take off Find a flying site clear of buildings, trees, power lines and other obstructions. Until you know how much area will be required and have mastered flying your plane in confined spaces, choose a site which is at least the size of two to three football fields - a flying field specifically for R/C planes is best. Never fly near people - especially children, who can wander unpredictably.
EN Trouble shooting Problem Possible Cause Solution Aircraft will not respond to the throttlebut responds to other controls. -ESC is not armed. -Throttle channel is reversed. -Lower throttle stick and throttle trim to lowest settings. -Reverse throttle channel on transmitter. Extra propeller noise or extra vibration. -Damaged spinner, propeller, -Replace damaged parts. motor or motor mount. -Loose propeller and spinner parts. -Tighten parts for propeller adapter, propeller and spinner.
EN User Manual of Brushless Speed Controller Thanks for purchasing our Electronic Speed Controller (ESC). High power system for RC model is very dangerous, please read this manual carefully. In that we have no control over the correct use, installation, application, or maintenance of our products,no liability shall be assumed nor accepted for any damages, losses or costs resulting from the use of the product. Any claims arising from the operating, failure or malfunctioning etc. will be denied.
EN User Manual of Brushless Speed Controller Begin To Use Your New ESC IMPORTANT! Because different transmitter has different throttle range, please calibrate throttle range before flying. Throttle range setting (Throttle range should be reset whenever a new transmitter is being used) 1.Switch on the transmi t ter, move throttle stick to the top position. 2.Connect battery pack to the ESC, and wait for about 2 seconds. 3.
EN Program the ESC with your transmitter (4 Steps) Note: Please make sure the throttle curve is set to 0 when the throttle stick is at bottom position and 100% for the top position. NO.1 Enter program mode 1.Switch on transmitter, move throttle stick to top position, connect the battery pack to ESC 2.Wait for 2 seconds, the motor should emit special tone like "beep-beep-" 3.Wait for another 5 seconds, special tone like "♪56712" should be emitted, which means program mode is entered. NO.
