1/6 1970 Suzuki Jimny RTR Manual

ManualsBrandsFMS ManualsCars & Trucks1/6 1970 Suzuki Jimny 4WD Brushed RTR - SCRATCH & DENT

Table Of Contents

Length:546mm

Width: 233mm

Height:265mm

Wheel base: 330mm

Ground clearance: 50mm

Approach angle: 41°

Departure angle: 48°

SPECIFICATION

1:6 jimny

Instruction Manual

操作手册

Summary of content (40 pages)

PAGE 1
:6 jimny Instruction Manual 操作手册 SPECIFICATION Length:546mm Width: 233mm Height:265mm Wheel base: 330mm Ground clearance: 50mm Approach angle: 41° Departure angle: 48°
PAGE 2
EN TABLE OF CONTENTS INTRODUCTION ................................................................................................................................................................ 02 TRANSMITTER INTRUCTION ......................................................................................................................................... 02 THROTTLE STICK POSITION ..............................................................................................................................
PAGE 3
EN Introduction Jimny, a legendary car, which successfully ﬁlled the market gap with its small displacement, small size, low price and unique market position, was born to break the traditional views on oﬀ-road vehicles and demonstrated itself as a reliable tool for oﬀ-road enthusiasts. The predecessor of the Jimny was the Hope Star ON 4WD of Hope Motors, which was sold to Suzuki Motor in 1968. 1970 saw the introduction of the LJ10 weighing 600kg with a 359cc two-stroke inline twin-cylinder equipped.
PAGE 4
EN Panel Flip Cover Steering Trim (ST.TRIM +) Steering Reverse Switch (ST.REV) Throttle Trim (TH.TRIM +) Power indicator LED (R. LED) Steering D/R (ST.D / R +) Steering Trim (ST.TRIM-) Lanyard Eye Status indicator green LED (G.LED) Base, 4 * AA battery compartment Throttle Trim (TH.TRIM-) Three-position switch (CH3)） Steering D/R (ST.
PAGE 5
EN Getting Started Before operation, install the battery and connect the system as instructed below. Transmitter Battery Installation Danger Only use speciﬁed battery (X4 AA batteries). Danger Do not open, disassemble, or attempt to repair the battery. Danger Do not crush/puncture the battery, or short the external contacts. Danger Do not expose to excessive heat or liquids. Danger Do not drop the battery or expose to strong shocks or vibrations.
PAGE 6
EN Instructions After setting up, follow the instructions below to operate the system. 1、Power On Follow the steps below to turn on the transmitter: 1. Check to make sure that that battery is fully charged and installed correctly. 2.Toggle the switch to the [ON] position. When active the R.LED will be lit. 3. Connect the receiver to power. For safety always power on the transmitter before the receiver. Note Operate with caution in order to avoid damage or injury.
PAGE 7
EN 4、Power Oﬀ Follow the steps below to turn oﬀ the system: 1.Disconnect the receiver power. 2.Toggle the transmitter's power switch to the oﬀ position. Danger Make sure to disconnect the receiver power before turning oﬀ the transmitter. Failure to do so may lead to damage or serious injury. System Functions This section focuses on the functions and how to use them. 1、Channel Description The transmitter outputs a total of 4 channels, which are allocated as follows: 1. CH1：Steering Wheel 3.
PAGE 8
EN 4、D/R ST.D / R is for servo travel adjustment, which can be multiplexed as CH2 (throttle), CH3, CH4 servo travel adjustment, see [5.5 Mode Switch] for multiplex switching mode; Adjustment range: 0-120%(the default is 100%), the step is 5%. ST.D / R +: increase servo travel; ST.D / R -: decrease servo travel. LED Indicator: When using the trim keys the G.LED will ﬂash slowly on short presses and quickly on long presses. When the ratio value is at both ends (0/120%), the ST.
PAGE 9
EN Instructions 1、Transmitter speciﬁcation( FS-G4P) Product Model FS-G4P Channels 4 Model Type Car, Boat RF 2S 锂电或5-6芯镍氢电 2-3S锂电或5-9芯镍氢电 2.4GHz 540或 550电机≥8T或 RPM <45000@7.2V RF Power <20dBm 2.4GHz Protocol 阻抗 Distance ANT 前进：0.0008欧姆，后退： 0.0016欧姆 >300m （ground） Channel Resolution 1024 Battery 6V DC 1.5AA*4 Charging Interface 2S 锂电或5-6芯镍氢电 NO 550电机≥8T或 RPM <45000@7.2V 540或 Life time According to battery type Low Voltage Warning 阻抗 Antenna Type <4.2V 前进：0.0008欧姆，后退： 0.
PAGE 10
EN Model WP-1040-BRUSHED WP-1040-BRUSHED-Crawler& Boat * Cont. / Burst Current Forward: 40A / 180A Backward: 20A / 90A Input 2-3S Lipo, 5-9 Cells NiMH Cars Applicable 1:10 on-road, oﬀ-road Buggy, Truggy, SCT 1:10 Crawler, Tank &Boat Motor Limit 09 2S Lipoor 5-6 cells NiMH 540 or 550 size motor ≥12T or RPM < 30000 @7.2V 3S Lipo or 7-9 cells NiMH 540 or 550 size motor ≥18T or RPM < 20000 @7.2V Resistance Fwd: 0.002 Ohm, Bwd: 0.
PAGE 11
EN Trouble Possible Reason Solution After power on, motor can’t work, no sound is emitted, and LED is oﬀ. The ESC doesn’t get its working voltage; Connections between battery pack and ESC are broken. Check the battery wires connection or replace the defective connectors. Switch is damaged. Replace the switch. Throttle signal is abnormal. Check the throttle wire connection; make sure it is plugged into the throttle channel of the receiver. Automatic throttle range calibration is failed.
PAGE 12
EN Operating the vehicle Step 1: turn on the transmitter, the headlamp of the transmitter will ﬂash and enter the frequency matching mode. Step 2: turn on the receiver switch, the headlight will ﬂash and enter the frequency matching mode. Step 3: when the transmitter and receiver are successful in frequency up, the front lights of the transmitter will be on for a long time, and the front lights of the vehicle will be oﬀ. Assembling Install the rearview mirrors and the top bow assembly as showned below.
PAGE 13
EN Setting the Gear Mesh The gear mesh is the clearance between the pinion and spur gears in your vehicle. If the motor or gearing components are replaced,check that the gears are not meshing too tightly as this may cause premature wear. Charging the Battery Always charge LiPo batteries on non-ﬂammable, heat-resistant surfaces. Always use a LiPo-safe bag or container while charging. Do not allow LiPo cells to overheat at any time.
PAGE 14
EN SERVO BATTERY Lipo PCB NIMH BIND MOTOR NOTE 13 1.If it is not in use for a long time, unplug and take oﬀ the battery to prevent batery leakage 2.Do not open, disassemble, or attempt to repair the battery.
PAGE 15
EN CE Warning The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.
PAGE 16
CN 目录产品介绍 ............................................................................................................................................................................ 16 发射机概览 ......................................................................................................................................................................... 16 油门扳机位置 ...........................................................................................................................................
PAGE 17
CN 产品介绍吉姆尼，一款传奇车型，它的出现打破了人们对于硬派越野车的固有认知。凭借着小排量、小尺寸、低价格，以及独树一帜的市场定位，精准地填补了市场空白，并成为了众多越野爱好者承载梦想的可靠工具。吉姆尼的前身是希望汽车的希望之星ON型4WD，1968年出售给铃木汽车。1970年经过铃木改进，搭载 359cc两冲程直列双缸，车重仅600kg的LJ10问世。 FMS获得铃木公司授权打造的第一代吉姆尼LJ10和真车一样，采用金属大梁，非承载式底盘，前后钢板弹簧悬挂，万向节传动。比例则是完全精准的1/6，座椅采用软胶包裹，模拟真实座椅的柔软度和塌陷效果，搭配1/6 人偶，呈现完美坐姿和行驶姿态。电机、电调、接收机和电池全部整合到引擎盖下方，打开引擎盖即可看到所有设备，换电、设定、维护更加方便。风挡可以向前放倒，后视镜采用真镜片制作，方向盘联动，两侧车门位置的安全杆也可以像真车一样放倒。方向盘，微缩影仪表盘和机械按钮、手动排档、脚踏板组等内饰都精细做出像真件。全尺寸备胎，备胎架向右侧开启后，尾门可以放倒，后斗空间得以完全呈现，搭载各类仿真零件十分方便，演出不同风格也能轻松实现。黑色防滚架为可拆卸
PAGE 18
CN 功能面板保护盖方向微调按键（ST.TRIM+）方向倒置开关（ST.REV）油门微调按键（TH.TRIM+）电源指示灯红色LED（R.LED）方向比例调节按键（ST.D/R+）方向微调按键（ST.TRIM-）挂绳孔状态指示灯绿色LED（G.LED）底座，4*AA电池仓油门微调按键（TH.TRIM-）三档拨动开关（CH3）方向比例调节按键（ST.D/R-）按键开关（CH4）电源开关方向手轮，左右各35度（CH1）对码按键（BIND）油门扣机，前25度后12.5度（CH2）油门倒置开关（TH.
PAGE 19
CN 使用前准备开始操作前，请按照本章的顺序和指引安装电池、连接设备。发射机电池安装危险仅使用厂家指定的电池。危险请勿打开、拆卸或自行维修电池。危险请勿挤压、刺穿或接触电池的金属端子。危险请勿将电池置于高温环境或液体中。危险如果不按照说明方法操作，可能导致操作者或他人遭受较大伤害。危险请将电池存放在干燥阴凉的环境中。危险如果电池损坏，请立即停止使用。电池类型使用: AA电池请按照以下步骤安装发射机电池: 1.打开电池仓盖。 2.将4颗电量充足的AA电池装入电池仓内，确保电池上的金属端子与电池仓内的金属端子接触。 3.盖好电池仓盖。低电量报警:当电量低于4.2v时，面板上的G.
PAGE 20
CN 操作指引准备操作完成后，您可以按照本章指引开始使用本产品。 1、开机请按照以下步骤进行开机: 1. 检查系统状态，确保 :电池电量充足且安装正确。 2. 将开关拨到 [0n] 位置，R.LED 灯常亮。 3. 连接接收机电源。注意 : 为保障模型及人员安全，使用时请先打开发射机再给接收机上电。警告此时系统已启动，请谨慎操作,否则可能导致产品损坏或人员伤亡。警告为了您的安全请将发射机开关和油门打到安全位置。 2、对码（发射机和接收机在出厂前已对码成功。）如需更换其他的发射机或接收机，请按照如下步骤进行对码: 1. 如需更换其他的发射机或接收机，请按照如下步骤进行对码 :进入对码状态后松开“BIND” 键； 2. 接收机上电自动进入对码 ; 3.
PAGE 21
CN 4、关机请按照以下步骤进行关机: 1.断开接收机电源。 2.将开关拨到[OFF]位置，使发射机关闭。危险关闭时，请务必先关闭接收机电源，再关闭发射机，否则可能导致模型损坏、人员受伤。系统功能此章节主要介绍系统各项功能操作。 1、通道说明该发射机共输出4个通道，分配如下: 1. CH1: 方向手轮 2. CH2: 油门 ] 扣机 3. CH3: 三档开关 4. CH4: 复位按键注意：CH4 按键开机默认输出 1000us，按压操作一下通道值翻转 - 次，数值在 1000us/2000us 之间互相切换。 2、通道反向（该功能用于调整舵机或马达的动作方向。）按键ST.REV/TH.REV分别为CH1、CH2通道反向按键，开关上拨表示反向，下拨表示正常。 3、微调按键ST.TRIM和TH.TRIM分别为CH1 (方向)和CH2 (油门)的微调按键。调节范围: -120us-+120us，微调步进为4us; ST.TRIM+/TH.TRIM+:增大微调值; ST.TRIM-/TH.TRIM-:减少微调值。 LED指示情况: 操作- -次微调键G.
PAGE 22
CN 4、方向比例 ST.D/R为CH1方向比例调节，默认为最大100%，步进为5% 调节范围 : 0- 100%; ST.D/R+: 增加比例 ; ST.D/R-: 较小比例。 LED 指示情况 : 操作一次按键 G.LED 闪烁一次，长按快闪当比例值位于两端时 (0/100%) , 按键无效且 G.LED 无指示 ( 如比例值已调至 100%，此时按 ST.D/R+ 键无效且 G.LED 无指示 ) 5、失控保护此功能用于当接收机无法正常收到发射机的信号时，对应通道舵机移动至预先设定的位置，保护模型和操作人员的安全。功能设置 : 发射机开机正常通讯状态下，将需要设置的通道保持在需要设定的失控保护值位置保持不动，同时长按对码键 (BIND) 3S，G.
PAGE 23
CN 产品规格 1、发射机规格 FS-G4P 产品型号 FS-G4P 通道个数 4 适配模型车、船无线频率 2S 锂电或 5-6芯镍氢电发射功率无线协议 2-3S锂电或 5-9芯镍氢电 2.4GHz 540或 550电机≥8T或 RPM <45000@7.2V <20dBm 阻抗 ANT 前进：0.0008欧姆，后退：0.0016欧姆遥控距离 >300m( 空旷无干扰地面距离 ) 通道分辨率 1024 级 2-3S锂电或5-9芯镍氢电电池 6V DC 1.5AA*4 充电接口 2S 锂电或5-6芯镍氢电续航时间低电压报警无 540或 550电机≥8T或 RPM <45000@7.2V 依电池类型阻抗 <4.2V 前进：0.0008欧姆，后退： 0.0016欧姆天线类型内置单天线数据接口无温度范围 -10°C ~ +60°C 湿度范围 2S 锂电或5-6芯镍氢电在线更新遥控器颜色 2-3S锂电或5-9芯镍氢电 20-95% 540或 550电机≥8T或 RPM <45000@7.
PAGE 24
CN 型号 WP-1040-BRUSHED WP-1040-BRUSHED-Crawler&Boat * 正向持续/峰值电流（10秒）反向持续/峰值电流（10秒） 40A / 180A 20A / 90A 支持电压范围 2-3节锂电（Lipo）或 5-9节镍氢（NiMH）电池主要适用车型普通版：1/10 电房、电越、短卡、大脚、卡车攀爬/船用版：1/10 攀爬车、坦克及各种模型船支持电机 T数 540或550尺寸电机≥12T 或RPM低于30000 @7.2V 3节锂电或9节镍氢 540或550尺寸电机≥18T 或RPM低于 20000 @7.2V 内阻（单桥臂）正转0.002欧姆，反转0.004 欧姆 BEC输出 6V/2A（线性稳压BEC）尺寸（mm）重量 23 2节锂电或6节镍氢 WP-1040-BRUSHED:46.5*34*28.5 WP-1040-BRUSHED-Crawler&Boat:46.5*34*28.
PAGE 25
CN 故障现象上电后指示灯不亮，不自检，无鸣音。上电后红色LED 闪烁，电机无法启动。遥控器做前进操作，车子反而倒退。车子无法达到全速，油门打到最大，红灯不恒亮。车子无法倒车。车子正向加油不走，反向倒车却行走。电机转动过程中，突然停转。车子无法前进也无法倒车，指示灯正常。可能原因解决方法 1. 检查电池到电调的电源输入通路是否有焊接不良情况，并重新焊好。 2. 更换电调开关。 1. 将电调的油门排线按正确方向插到接收机的油门 1. 电调油门线插反或通道插错。通道（Throttle, 通常为CH2）。 2. 电调无法完成油门自检校调。 2. 将遥控器的油门通道的中点微调 “TRIM”调为0 或相应旋钮调到中点位置。 1. 将马达的两条线互换。 1. 遥控器油门通道方向设置错误 2. 将遥控器油门通道反向，从原“NOR”换为“REV” 或马达接线错误。或从原”REV”换为 “NOR”。 1. 将遥控器油门通道的 “D/R” 、 “EPA” 、“ATL” 等参数调到100%或相应旋钮调到最大位置，油门通 1.
PAGE 26
CN 车辆操作步骤1：打开发射器, 发射器前灯会闪亮, 进入对频模式。步骤2：打开接收器开关, 车前灯会闪亮, 进入对频模式。步骤3：当发射器,接收器对上频成功时, 发射器前灯会长亮, 车前灯会关闭。车辆安装如图所示，安装后视镜及尾架。 25
PAGE 27
CN 齿轮齿盒设置齿轮啮合是模型车内小齿轮和直齿轮之间的间隙配合。如果更换电机或齿轮传动部件，请检查齿轮咬合是否过于紧密，如过于紧密，则可能导致过早出现磨损。电池充电警告 1.长期不使用时，应拔开并取出电池，以防电池漏液。 2.
PAGE 28
(EN) WHEELS ASSEMBLY C1301 (CN) 轮胎组 C1300 C1301 C1301 C1301 C1301 (EN) CAR WINDOW ASSEMBLY (CN) 车窗组 C1312 C1312 C1312 C1312 C1312 C1312 C1312 C1312 C1312 27
PAGE 29
(EN) SEAT ASSEMBLY (CN) 座椅组 C1314 C1314 C1314 C1314 C1314 C1314 C1314 C1314 C1314 C1314 C1314 C1314 C1314 (EN) STEERING LINKAGE ASSEMBLY (CN) 转向拉杆组 C1009 C1063 C1063 C1009 C1009 C1063 C1063 C1009 C1063 28
PAGE 30
(EN) STEERINGSERVO (CN) 方向盘舵机组 C1035 (EN) FRONT AXLE ASSEMBLY (CN) 前桥组 C1302 C1303 C1305 C1304 C1304 29
PAGE 31
(EN) REAR AXLE ASSEMBLY (CN) 后桥组 C1308 C1310 C1100 C1309 (EN) TRANSMISSION GEAR BOX ASSEMBLY C1012 (CN) 中传动牙箱 C1076 30
PAGE 32
(EN) TRANSMISSION SHAFT ASSEMBLY (CN) 传动轴组 C1010 (EN) MAIN GEAR BOX ASSEMBLY (CN) 驱动牙箱 C1011 31
PAGE 33
(EN) OIL SHOCK ABSORBERS ASSEMBLY (CN) 避振组 C1311 (EN) CAR BODY ASSEMBLY (CN) 车壳半成品 C1317 C1326 C1325 C1323 C1320 C1320 32
PAGE 34
(EN) CAR BODY FINISHING (CN) 车壳成品 C1314 C1312 C1327 C1317 33
PAGE 35
EN “S" for spare part PART NUMER C1011 C1010 C1012 C1021 C1300 C1301 C1302 C1303 C1304 C1305 C1016 C1063 C1308 C1309 C1100 C1310 C1311 C1312 C1313 C1314 C1315 C1316 C1317 C1318 C1319 C1320 C1321 C1322 C1323 C1324 C1325 C1326 C1327 C1328 C1329 C1330 C1331 C1009 C1020 C1022 C1023 C1066 C1067 C1068 “O" for optional part PRODUCT DESCRIPTION S/O MAIN GEAR BOX SET TRANSMISSION SHAFT ASSEMBLY TRANSMISSION GEAR BOX ASSEMBLY 12mm WHEEL HEX SET 1:6 JIMNY TYRES 1:6 JIMNY WHEELS 1:6 JIMNY FRONT AXLE ASSEMBLY 1:6 J
PAGE 36
EN “S" for spare part PART NUMER C1070 C1076 C1080 C1081 C1082 C1077 C1082 C1084 C1085 C1097 C1101 C1055 C1056 C1105 C1106 C1035 C1107 C1108 35 PRODUCT DESCRIPTION 1:6 5.8 BALL HEAD 1:6 GEAR SET 35T BRUSHED 550 MOTOR GASKET SET 1:6 FRONT OUTDRIVE SHAFT ASSEMBLY 1:6 R DRIVE CUP SET 1:6 ALUMINIUM STEERING C HUB PARTS BUSHING SET 1:6 ALUMINIUM STEERING BRACKET SET 1:6 Pinion Gear 1:6 METAL TRANSMISSION SHAFT WATERPROOF 60A BRUSHED ESC WATERPROOF 15KG METAL GEAR SERVO 2.4G Transmitter FIBRE STYLE 2.
PAGE 37
CN “S" 为配件 PART NUMER C1011 C1010 C1012 C1021 C1300 C1301 C1302 C1303 C1304 C1305 C1016 C1063 C1308 C1309 C1100 C1310 C1311 C1312 C1313 C1314 C1315 C1316 C1317 C1318 C1319 C1320 C1321 C1322 C1323 C1324 C1325 C1326 C1327 C1328 C1329 C1330 C1331 C1009 C1020 C1022 C1023 C1066 C1067 C1068 “O" 为升级件 PRODUCT DESCRIPTION S/O 驱动牙箱组散件传动轴成品中传动牙箱成品 12mm 车轮6角件 1:6 吉姆尼轮胎 1:6 吉姆尼车轮 1:6 吉姆尼前桥成品 1:6 吉姆尼前桥胶件 1:6 吉姆尼前钢板弹簧 1:6 前轮传动总成 1:6 转向C座件 1:6 转向连杆 1:6 吉姆尼后桥成品 1:6 吉姆尼后钢板弹簧 1:6 后轮轴 1:6 吉姆尼后桥胶件 1:6 吉姆尼避振器品成 (一对
PAGE 38
CN “S" 为配件 PART NUMER C1070 C1076 C1080 C1081 C1082 C1077 C1082 C1084 C1085 C1097 C1101 C1055 C1056 C1105 C1106 C1035 C1107 C1108 37 “O" 为升级件 PRODUCT DESCRIPTION 1:6 5.8波头 1:6 齿轮套装 35T 有刷550电机垫圈前轮传动总成 1:6 驱动杯套装 1:6 金属转向C座件套筒介子 1:6 金属转向支架 1:6 马达齿 1:6 五金传动轴成品 1:6 防水60A电调防水15KG 金属齿舵机 2.4G 发射器碳纤纹风格 2.
PAGE 39
DISTRIBUTOR North America: Horizon Hobby LLC 2904 Research Road Champaign, IL 61822, USA Tel.: 217-403-3584 Sweden: Minicars Hobby Distribution AB Annelundsgatan 17C 749 40 Enköping, Sweden Tel.: +46-171-14 30 02 The United Kingdom: CML Distribution Ltd Saxon House, Saxon Business Park, Hanbury Road Bromsgrove, Worcestershire B60 4AD, England Tel.: +44 (0)1527 575349 Australia: Model Engines Pty Ltd Unit 1/32 Bluett Drive Smeaton Grange NSW 2567 Australia Tel.
PAGE 40
Declaration of Conformity (DoC) We, Dongguan Solid Model Technology Co.,Ltd 3/F, Building B, 3rd Industry Zone, Matigang, Dalingshan Town Dongguan City of China 523810. Phone:0769-86976655 Web:www.fmsmodel.com declare under our responsibility that the product: Type of Equipment: Driving System & 2.