Instructions for Use
WARNINGS
1. This product is only equipped for radio controlled
models;
2. The usage of this product should be approved by local
relevant law or regulations;
3. We will not be responsible for the damages caused by
unauthorized modification, adjustment or replacement
of parts of this product;
4. The manual may be altered without prior notice.
Please contact us if you have any corrections or
clarifications that should be made in the manual.
Before starting the transmitter, make sure the transmitter
batteries are well loaded .The voltage of transmitter
batteries is never lower than 4.6V. And please check and
confirm that the servos are all well and properly
connected.
Keep the radio system away from moist, high temperature
and strong shake. Do not clean the product with solvent.
The antenna does not touch anything else when power
switch is turned on. Do not leave this product and its
accessories within the reach of small children.
Please use this product according to your local relevant
law or regulation, we are not responsible for any incidents
or damages.
Transmitter/Receiver Binding
1. Short-Connect the BIND channel of receiver with
Short-Nut.
2. Power on the receiver. The LED will flash quickly to
indicate the receiver is ready to bind.
3. Press and hold the BIND button on the transmitter and
power-on. The LED of transmitter will flash green/red
slowly.
4. The transmitter and receiver will bind automatically.
5. After about 8 second, the transmitter will go into the
work stage, the LED of transmitter will turn solid green.
6.
Check the receiver, if the LED turns solid green. That
means bind procedure complete.
7. If not, please repeat step 2-5 again.
8. Remove the Short-Nut.
Turn ON And Turn OFF
Turn on
Power on the transmitter, the LED of transmitter turns
GREEN.
Power on the receiver, when the LED of receiver turns
GREEN, the device is paired and prepared to work.
Turn off
Remove the power of receiver.
Power off the transmitter.
Connection Diagram
Switch Switch 1 Switch 2 Switch 3 Switch 4 Switch 5 Switch 6
Reverse
Aileron
Reverse
Elevator
Reverse
Throttle
Reverse
Rudder
Reverse
Mode1
Mode2
Fixed-Wing
Delta
DELTA MODE
Receiver channel distribution:
Ch1: Aileron Ch2: Elevator Ch3: Throttle Ch4: Rudder
Switch to “DELTA” position and enter DELTA mode, aileron
and elevator is mixed, as for triangle planes, tailless planes.
Transmitter
Receiver Channel Mixing
Stick
CH1
CH2
Aileron Stick
+50%
+50%
Elevator Stick
+50%
-50%
FIXED-WING MODE
Receiver channel distribution:
Ch1: Aileron Ch2: Elevator Ch3: Throttle Ch4: Rudder
Switch to “FIXED-WING” position and enter FIXED-WING
Plane mode.
MODE
Receiver Channel Distribution:
CH1:Aileron
CH2:Elevator
CH3:Throttle
CH4:Rudder
Receiver Channel Distribution:
CH1:Aileron
CH2:Elevator
CH3:Throttle
CH4:Rudder
Receiver
Technology Data
Transmitter
Item: F-4
Channels: 4
Resolution: 1024
Frequency: 2.4GHz ISM Frequency Range
Spread Spectrum Mode: FHSS
Frequency point: 152PCS
Bandwidth: 500kHz
Frequency interval: 4M
Output Power: ≤100mW
Working current: ≤150mA
Working voltage: 1.2V*4NiCad/NiMH
Dimensions: 152mm * 163mm * 65mm
Net weight: 252g
Receiver
Channels: 4
Frequency: 2.4GHz ISM Frequency range
Spread Spectrum Mode: FHSS
Power: 4.8-6.0V
Measurement: 34mm * 21mm * 13.5mm
Net weight:6.8g
Low Battery Warning
When the LED starts blinking quickly with RED and
GREEN, please change the battery immediately.
Do NOT operate your radio below low battery. Always shut
your device off as soon as possible after the low battery
warning loss of control.