WARNING! WARNING: Read the ENTIRE instruction. manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury. This isa sophisticated hobby product arid NOT a toy. It must be operated with caution and common sense and requires some basic mechanical ability. : Failure to operate this Product in a safe and responsible manner. could result in injury or damage to the product or.
ZHFMS able of contents Kit contents 1 The osteoarthritis 1 Spare parts list content The Illustration of the spare parts Kit Inspection a 3 Charging the Flight Battery .. 3 Using Steps Charging Function Description Sell Checking Function Protection Function Troubleshooting Low Voltage Cut off (LVC) Assemblywoman . Install the main wing Install the battery Install the elevator Disassembly Get your modelreadytofly-11 Important ESC and plane information The transmitter and model setup Check the C.G.
Kit contents 1. The fuselage assembly (With the motor, the canopy, the electronic parts, ESC) 2. Horizontal stabilizer 3. Propeller and spinner 4. Spare parts bag 5. Main wing tube 6. Main wing e parts list J Replacement parts for the FOX are available using the order numbers in the Spare parts list that follows. The fastest, most economical service can be provided by your hobby dealer or mail-order company.
GEMS Spare parts list content Spare parts list content MT 101 Fuselage ( With all the plastic parts and rudder installed) MT 102 Main wing set ( With the control horn in stored) MT 103 Horizontal stabilizer ( With the elevator connector installed) MT 104 Spinner MT 301 Propeller MT 302 Canopy {one plastic canopy) MT 303 Canopy (one foam canopy } MT 304 Sticker MT 305 Pipe MT 306 Motor Board (V2) MT 307 Linkage Rods MS-Motor 4018 KV900 F MS-ESC-30A (150mm input cable) 1300mAh 35C FMSSER9GP Note: All of the p
Kit inspect ) Before starting to build, inspect the parts to make sure they are acceptable quality. If any parts are missing or are not in good shape or acceptable quality, or if you need assistance with setup and assembly, please feel free to contact Fm Steam. Please write down the name of the parts when you are reporting defective or missing of them. Fm Steam Product Support ADDRESS: 3/F, Building B, 3rd Industry Zone, Mating, Tangshan Town, Guangdong City, P.R.
raging the Flight Battery ) Electrical Parameters Parameter Min Type Max Unit Working Voltage Input Power 15 w Work Temperature -20 45 °C Store Temperature -20 65 °C Charging Stop Voltage| 4.19 4.20 4.21 v Charging Current 1000 mA Balancing Current 150 200 mA Activate Current 80 120 mA Using Steps: 1. Connect the charger to adapter with enough voltage and wattage, then the Power LED will turn on; 2.
Flimflams Charging the Flight Battery J Protection Function 1. Reverse connection protection of input 2. Reverse connection protection of output 3. Short circuit protection of output 4. Over voltage protection of output Troubleshooting 1. Power LED does not shine — Adapter isn’t connected correctly. Please check the polarity and reconnect adapter. 2. Charging abruptly stops and tries to restart constantly during charging — Output power of the adapter is not sufficient, please replace the adapter. 3.
GEMS le the plane ) fig. 1 fig. 2 Connect the aileron control rod linkages 0 1) Slide the provided piece of fuel tubing over the control rod linkage and then insert the control rod linkage thru the desired hole in the aileron servo arm (fig. 3). Note: For a single rate transmitter use the first hole to achieve a high rate setting. Use the third hole nearest the servo to achieve a low rate setting.
n wing 1. Insert the pipe into the wing, 3. Assemble the full wing. Insert the Connect the Y cable wings at the both sides of fuselage. Insert the Y cable of aileron from the bottom front . 2. Assemble the wing. Connect the opposite end of Y cable. 4. Fix the wing and pipe provided screws. Do not over tighten the screws but make sure it's tight enough.
SE FMs Assemble an trey Receiver 1. Slide the battery into the hook and loop ring from Aileron 1 the back of the battery compartment with the LL Channel-1 cable toward the rear side of the hatch. —Allie Elevator 2 Chan — Elev Throttle 3 Channel-3 — Thor Rudder 4 Channel-4 — Rudy Flaps 8 Channel-6 — Flaps The placement of the receiver 1. Place the receiver in the fuselage cavity on the rear end of the canopy hatch. 2. Secure the battery into place using the hook strip.
HIMSELF Install the elevator 3. Secure the rudder using the provided screws PM 2PCS). Note: Do not over tighten the screws but make sure it is tight enough. 1. Install the linkage rod of the elevator. 2. Insert the Horizontal stabilizer half into 4.
the plane y 1. The spinner is snapped into the propeller 4. Always check that the foldaway propeller blades back plate. To remove, hold the spinner near the are attached properly. Make sure that the root of the propeller and squeeze gently. bolts are on completely, but not too tight or they will prevent the blades from spinning freely. 2. Remove the nut using a nose needle pier or a socket wrench while holding the propeller set into place. 3. Remove the propeller set from the motor shaft.
Salaams Get your model ready ) model Information 1. The ESC included with the FOX has a safe start. If the motor battery is connected to the ESC and the throttle stick is not in the low throttle or off position, the motor will not start until the throttle stick is moved to the low throttle or off position. Once the throttle stick is moved to the low throttle or off position, the motor will emit a series of beeps. Several beeps with the same tune means the ESC has detect the cells of the battery.
FES Get your model ready toll Tips: Make sure all control sticks on your radio are in the neutral position (rudder, elevator, ailerons) and the throttle in the OFF position. Make sure both ailerons move up and down {travel} the same amount. This model tracks well when the left and right ailerons travel the same amount in response to the control stick. 1. Move the controls on the transmitter to make sure aircraft control surface move correctly. See diagrams below.
3. Align the control surfaces well by adjusting the linkage rod in the control connector. The ailerons align with the wing root fillet, the counterbalance leading edge of the elevator aligns with the horizontal stabilizer leading edge and the counterbalance leading edge of the rudder with the vertical stabilizer leading edge. Note: Use a drop of thread lock on the grub screws before securing the linkage rod. D Aileron Check the motor rotating direction 1.
“a DIMS ec Center of Gravity) ) Center of Gravity When balancing your model, adjust the motor battery as necessary so the model is level or slightly nose down. This the correct balance point for your model. After the first flights, the CG position can be adjusted for your personal preference. 1. The recommended Center of Gravity (CG) location for your model is (40mm) forward from the leading edge of the main wing (as shown) with the battery pack installed. Mark the location of the CG on top of the wing. 2.
HIMSELF Before the model flying |] site Find a flying site clear of buildings, trees, power lines and other obstructions. Until you know how much area will be required and have mastered flying your plane in confined spaces, choose a site which is at least the size of two to three football fields — a flying field specifically for R/C planes is best. Never fly near people— especially children who can wander unpredictably.
Commas Take ofl While applying power slowly steer to keep the model straight, the model should accelerate quickly. As the model gains flight speed, you will want to climb at a steady and even rate. The FOX will climb out at a nice angle of attack (AORTA. Flying Always choose a wide-open space for flying your plane. It is ideal for you to fly at a sanctioned flying field. If you are not flying at an approved site, always avoid flying near houses, trees, wires and buildings.
Lamaisms Troubleshooting J Problem Possible Cause Solution Aircraft will not respond to the throttle but responds to other controls. -Excises not armed. Throttle channel is reversed. Lower throttle stick and throttle trim to lowest settings. Reverse throttle channel on transmitter. Extra propeller noise or extra Vibration. Damaged spinner, propeller, motor, or motor mount. Loose propeller and spinner parts. Propeller installed backwards. Replace damaged parts.
