220MM Super EZ V2 FLOAT Float included RIGID Durable EPO STABLE SMOOTH FLYING PERFORMANCE FMSMODEL.
WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to the product,personal property and cause serious injury. This is a sophisticated hobby product and NOT a toy. It must be operated with caution and common sense and failure to do so could result in injury or damage to the product or other property. This product is not intended for use by children without direct adult supervision.
Table of Contents Introductions ··························································································································3 Contents of Kit ························································································································4 Model Assembly ······················································································································5 Battery and radio installation ····················································
Wingspan: 1220mm (48.0in) Overall Length: 1020mm (40.2in) Flying Weight: Around 920g(31.4oz)1120(39.05oz) Motor Size: Brushless 3136-KV1230 Wing Load: 31.34 g/dm² (0.07oz/in²) Wing Area: 28.4 dm² (440.2sq.in) ESC: 20A Servo: No Float 9g Servo x 4, Float Included Servo x 5 Recommended Battery: 11.1V 1300-2200mAh 25C Contents of Kit Before assembly, please inspect the contents of the kit. The photo below details the contents of the kit and labels.
Model Assembly Main Wing Installation 1. Unpack the assessory bag of rudder, which includes servo arms , screws, linkage rods (including clevis and sleeve). Install the servo arms as shown in Figure 1. Install the linkage rod as shown in Figure 2. Pay attention to the direction of the servo arm. fig1 fig2 2. Unpack the assessory bag of elevator, which includes servo arms, screws, linkage rods (including clevis and sleeve). Install the servo arms as shown in Figure3.
Model Assembly Main Wing Installation 4. Fix the landing gear set with the screw, as shown in Figure7. 5. Find the Y-harness and connect it to both aileron servos. Connect the Y-harness to the receiver, then place the receiver into the fuselage. HKM 3.0*10 fig7 fig8 6. Assemble the main wing as shown in Figure 9.
Model Assembly Floats Set Installation: 7. Assemble the floats struts to the plastic part as shown in Figure 11 and secure the struts with screws. Screws 3*4 fig11 8. Fix the floats set with struts on the bottom of fuselage with screws as shown in Figure 12. HKM 3.
Battery and radio installation 1. Apply the hook tape to the cable end of the battery.(fig 13) 2. Slide the battery into the battery hatch with the power supply cable toward the rear end of the plane and the hook tape facing the bottom of the battery hatch. Note: You may need to relocate the battery position to acheieve the correct CG for your model.
Get your model ready to fly Important ESC and model information 1. The ESC included with the model has a safe start. If the motor battery is connected to the ESC and the throttle stick is not in the low throttle or off position, the motor will not start until the throttle stick is moved to the low throttle or off position. Once the throttle stick is moved to the low throttle or off position, the motor will emit a series of beeps.
Check the control throws The suggested control throw setting for FMS MODEL are as follows (dual rate setting): Elevator Aileron Rudder 15mm up/down 15mm up/down 12mm left/right 10mm up/down 10mm up/down 8mm left/right Tips: On first flight, fly the model in low rate.
11
Secure the spinner base a, propeller b, spinner plate c to the motor one by one. Fix the propeller with spinner cap d as the given spinning direction below. Check the C.G. (Center of Gravity) When balancing your model, adjust the motor battery as necessary so the model is level or slightly nose down. This is the correct balance point for your model. After the first flights, the CG position can be adjusted for your personal preference. 1.
Before flying the model Find a suitable flying site Find a flying site clear of buildings, trees, power lines and other obstructions. Until you know how much area will be required and have mastered flying your plane in confined spaces, choose a site which is at least the size of two to three football fields - a flying field specifically for R/C planes is best. Never fly near people especially children, who can wander unpredictably.
Flying Course Take off While applying power, slowly steer to keep the model straight. The model should accelerate quickly. As the model gains flight speed you will want to climb at a steady and even rate. It will climb out at a nice angle of attack (AOA). Flying Always choose a wide-open space for flying your plane. It is ideal for you to fly at a sanctioned flying field. If you are not flying at an approved site always avoid flying near houses, trees, wires and buildings.
Trouble shooting 15
Spare parts list content FMSPH101-1 FMSPH102 FMSPH103 FMSPH104 FMSPH105 FMSPH106 FMSPH108 FMSPH109 FMSPH110 FMSPH114 FMSPH115-1 FMSPH116-1 FMSPH117 FMSPROP022 FMSDJ009 FMSBM011 FMSDZ018 FMSKV1230 FMSESC20AE FMSSER9GPW FMSCHR01 FMSFLT004 Fuselage Main Wing Horizontal Stabilizer Cowl Battery Cover Spinner Front Landing Gear Set Tire set Wing Bolt Plate Sticker Linkage Rods Screws Pipe Propeller Motor Mount Motor Board Motor Shaft 3136 KV1230 Motor 20A ESC 9g Servo Charger Float Set Visit our website to see
ESC instruction Battery Pack A quality connector is essential ESC Brushless Controller Receiver 17 Motor
