FN SCAR® 20S AUTOLOADING RIFLE OWNER'S MANUAL
Important operating instructions for: FN SCAR® 20S AUTOLOADING RIFLES If you have any questions or comments regarding your new firearm, please contact us. FN Service Center 797 Old Clemson Rd Columbia, SC 29229 1-800-635-1321 customerservice@fnamerica.com www.fnamerica.com Please use the space below to record information about your new firearm.
11. Ammunition ......................................20 12. Magazine Capacity ...........................21 13. Loading .............................................21 13.1 Filling The Magazine ................22 13.2. Loading the Chamber from the Magazine ...........................23 19.5 Removal of the Gas Regulator and Gas Piston .................................38 20. Cleaning and Lubrication ................39 20.1 Cleaning Procedures ................40 20.2 Cleaning the Trigger Module ....42 20.
1. FOREWORD We are pleased that you have chosen an FN SCAR 20S autoloading rifle. The SCAR 20S combines the latest in autoloading rifle design, manufacture and testing methods to create a rifle worthy of the U.S. military’s special operations forces. The SCAR family of firearms represents the highest levels of reliable function, consistent accuracy, comfortable ergonomics and the operating precision and safety expected from an FN firearm. Unique and simple in design, the rifle is very easy to maintain.
2. CONTENTS OF THE STORAGE CASE The rifle and its accessories are supplied in a military-style, cardboard shipping container with foam insert. The contents of the container include: • Rifle • Design-fit foam insert that can be used in a typical mid length hard case • One 10-round magazine • Owner’s manual • Gun record book • Locking device and two keys (use the locking device when storing and transporting the rifle; always keep keys in a safe place.
3. SAFETY AND WARNINGS LIKE ALL FIREARMS, IF HANDLED IN A CARELESS OR RECKLESS MANNER, THIS RIFLE CAN BE VERY DANGEROUS. FAILURE TO FOLLOW THE INFORMATION IN THIS OWNER’S MANUAL COULD RESULT IN SERIOUS INJURY OR DEATH. ALWAYS WEAR SAFETY GLASSES AND HEARING PROTECTION WHENEVER YOU ARE SHOOTING. ALWAYS MAKE CERTAIN THAT PERSONS CLOSE TO YOU ARE SIMILARLY PROTECTED.
• Inadequate care of the firearm (e.g., corrosion, damage.) • Disregard of malfunctions • Resale in contradiction to law • Other circumstances beyond our direct and immediate control NOTICE! FN AMERICA RESERVES THE RIGHT TO REFUSE SERVICING A FIREARM THAT HAS BEEN MODIFIED BY REMOVAL OF METAL FROM THE BARREL, MODIFICATIONS OF THE FIRING MECHANISM AND/OR OTHER PARTS, AND WILL, IN SUCH A CASE, ALWAYS RECOMMEND RESTORING THE FIREARM TO ITS ORIGINAL SPECIFICATIONS.
4. FIREARM SAFETY INFORMATION FAILURE TO FOLLOW ANY OF THE FOLLOWING WARNINGS COULD RESULT IN SERIOUS INJURY OR DEATH. As a firearm owner, you accept a set of demanding responsibilities. How seriously you take these responsibilities can be the difference between life and death. There is no excuse for careless or abusive handling of any firearm. At all times handle this firearm and all other firearms with intense respect for their power and potential danger.
Remember, safe gun handling does not stop with your firearm’s mechanical safety devices, it starts there. Always treat this firearm with the respect due a loaded, ready-to-fire firearm. Some firearms do not have a mechanical safety. Many target firearms, lever-action firearms and rifles do not have manual safety mechanisms. Therefore, it is critical to read and understand the owner’s manual for every firearm which explains the safe operation of the firearm.
Wear shooting glasses to protect your eyes from flying particles. Allow proper distance (eye relief) between a scope and your eye when firing a scoped rifle or shotgun. Do not use unorthodox shooting methods that could cause the rearward travel of the slide or bolt of a firearm to contact your eyes, face or hands. Always keep a safe distance between the muzzle of your firearm and any persons nearby, as muzzle blast, debris and ejecting shells could inflict serious injury.
Take prudent safeguards to ensure your firearm does not become available to untrained, inexperienced or unwelcome hands. Store all firearms in secure, locked cases or a gun safe. Keep your firearm unloaded when not in use. At all times, comply with federal, state and local laws. For law enforcement and military personnel, refer to the procedures of your department on storing your firearm. 9. BEWARE OF BARREL OBSTRUCTIONS.
Service Center or a qualified gunsmith and the cause of the malfunction corrected before further use. Only after you have cleared the cartridge from the chamber and completely unloaded the firearm, glance down the barrel to make sure that there are no obstructions in the barrel. If there is an obstruction, completely clear the barrel before loading and firing again. Failure to follow these instructions can cause extensive damage to your firearm and possible serious injury to yourself and others. 11.
14. MAKE SURE OF ADEQUATE VENTILATION IN THE AREA THAT YOU DISCHARGE A FIREARM. LEAD EXPOSURE CAN OCCUR FROM DISCHARGING FIREARMS IN POORLY VENTILATED AREAS, CLEANING FIREARMS OR HANDLING AMMUNITION. Lead is a substance that has been known to cause birth defects, reproductive harm and other serious injury. Wash hands thoroughly after exposure to ammunition or after cleaning a firearm. 15.
20. BE CERTAIN YOUR FIREARM IS UNLOADED BEFORE CLEANING. Because so many gun accidents occur when a firearm is being cleaned, special and extreme care should be taken to be sure your firearm is unloaded before disassembly, cleaning and reassembly. Keep ammunition away from the cleaning location. Never test the mechanical function of any firearm with live ammunition. 21. TEACH AND SUPERVISE FIREARMS SAFETY TO ALL MEMBERS OF YOUR FAMILY, ESPECIALLY TO CHILDREN AND NONSHOOTERS.
25. WE RESERVE THE RIGHT TO REFUSE SERVICE ON FIREARMS THAT HAVE BEEN ALTERED, ADDED TO OR SUBSTANTIALLY CHANGED. Removal of metal from the barrel or modifications of the firing mechanism and/or operating parts may lead to a refusal of service on such firearms. We will charge the owner for parts and labor to return the firearm to original FN specifications. DO NOT, UNDER ANY CIRCUMSTANCES, ALTER THE TRIGGER, SAFETY OR OTHER PARTS OF THE FIRING MECHANISM OF THIS OR ANY OTHER FIREARM.
5.
12 o’clock Rail Gas Regulator Barrel Ejection Port 6 o’clock Rail Bolt Release 3 o’clock Rail Sling Attachment Point Serial Number LOP Adjustment button Check Rest Safety Selector, Left Side Trigger Check Rest Button Magazine Release, Left Side 15
5.1 DESCRIPTION The FN SCAR 20S is a gas-operated, semi-automatic repeating rifle. SCAR rifles are a direct result of the U.S. military’s search for a modular battle rifle that is easy to use and extremely reliable. SCAR rifles have been developed using the latest computer software, extensive materials testing, real-world research and end user assessments from special operations forces operators. This information has culminated in the next generation of technologically-advanced rifles.
round has been fired, the bolt will lock in the rearmost, open position. This allows fast, convenient reloading. 6. NOMENCLATURE In conventional firearm terminology, the position and movement of parts are described as they occur with the firearm horizontal and in normal firing position; i.e., the muzzle is forward or in front; the buttstock is rearward or to the rear; the trigger is downward or underneath; the barrel is upward or on top. For general parts nomenclature, refer to Figures 1 and 2. 7.
9. OPERATION OF THE SAFETY SELECTOR ALWAYS KEEP THE SAFETY SELECTOR IN THE ON-SAFE POSITION UNLESS SHOOTING IS IMMINENT. ALWAYS KEEP THE MUZZLE POINTED IN A SAFE DIRECTION. FAILURE TO FOLLOW THESE WARNINGS COULD RESULT IN SERIOUS INJURY OR DEATH. FN SCAR rifles utilize an ambidextrous safety selector located on the trigger module just rearward and above the trigger. This location allows the safety selector to be easily manipulated with the thumb of the firing hand.
10. BOLT RELEASE WHEN USING THE BOLT RELEASE ALWAYS KEEP THE MUZZLE POINTED IN A SAFE DIRECTION AND KEEP YOUR FINGERS AWAY FROM THE TRIGGER. UNLESS SHOOTING IS IMMINENT, ALWAYS REMOVE THE MAGAZINE FROM THE RIFLE BEFORE CLOSING THE BOLT TO PREVENT INADVERTENTLY LOADING A CARTRIDGE FROM THE MAGAZINE INTO THE CHAMBER. MAKE SURE YOUR FINGERS ARE SAFELY AWAY FROM THE EJECTION PORT AT ALL TIMES WHEN THE BOLT IS LOCKED OPEN AND WHEN THE BOLT IS RELEASED TO AVOID PINCHING THEM WHEN THE BOLT CLOSES.
10.2 BOLT LOCK FUNCTION FIGURE 6 The bolt release can also be used to lock the bolt in the rearward position when the magazine is removed. To lock the bolt in the open or rear position, pull the charging handle all the way to the rear and press inward on the bottom portion of the bolt release (Figure 6). 11. AMMUNITION Using the bolt release as a bolt lock. DO NOT USE AMMUNITION OTHER THAN WHAT IS DESIGNED FOR USE IN YOUR FN SCAR RIFLE. EXAMINE EVERY CARTRIDGE YOU PUT IN YOUR FIREARM.
FIGURE 7 7.62x51 1:12 Locations for caliber/cartridge marking. 12. MAGAZINE CAPACITY The FN SCAR 20S magazines are the same as the FN SCAR 17S magazines but unique to these rifles and should not be used in other rifles. No other magazine type should be used in your SCAR rifle. The specialized designs make the magazine highly reliable and result in easy maintenance and cleaning. SCAR 20S rifles have a standard magazine capacity of 10 cartridges.
DO NOT CARRY YOUR RIFLE WITH A CARTRIDGE IN THE CHAMBER TO AVOID ACCIDENTAL DISCHARGE. WHEN FIRING IS NO LONGER IMMINENT, PLACE THE SAFETY SELECTOR IN THE ON-SAFE POSITION, REMOVE THE MAGAZINE AND UNLOAD THE CHAMBER AS EXPLAINED IN SECTION 15.1. FAILURE TO FOLLOW THESE WARNINGS COULD RESULT IN SERIOUS INJURY OR DEATH. 13.1 FILLING THE MAGAZINE DO NOT INSERT THE MAGAZINE INTO THE RIFLE, NOR LOAD A CARTRIDGE INTO THE CHAMBER, UNLESS SHOOTING IS IMMINENT. 1.
4. Load the cartridges into the magazine by placing a cartridge on the top of the retaining lips and, with your thumb, pushing it straight down against the force of the follower spring until it locks into position under the retaining lips (Figure 10). Continue to fill the magazine in this manner. FIGURE 10 Press each cartridge straight down into the Care should be exercised in magazine and to the rear. positioning each cartridge so that its base is flush with the rear of the magazine.
4. If shooting is imminent, a cartridge can now be moved from the magazine to the chamber by pulling back fully on the charging handle and releasing it, or pressing on the top of the bolt release, and allowing the bolt to move forward into battery. If the bolt is not allowed to close in this manner, there is a possibility that it will not close completely, preventing the rifle from firing. 5.
This is the proper position for normal firing conditions. If the gas regulator is not in the 12 o’clock position the rifle may not function correctly. 3. Load a cartridge into the chamber as explained previously. With a cartridge in the chamber, you need only to move the safety selector to the off-safe position to make the rifle ready for firing. Do not move the safety selector to the off-safe position unless shooting is imminent.
4. When ready to fire, move the safety selector into the off-safe position, take aim and squeeze the trigger. DURING EXTENDED SHOOTING SESSIONS OR RAPID FIRING, THE 3, 6 AND 9 O’CLOCK ACCESSORY RAILS CAN BECOME EXTREMELY HOT. WEAR GLOVES TO PREVENT BURNING YOUR HANDS. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY. 5.
AFTER FIRING, OR WHEN SHOOTING IS NO LONGER IMMINENT, IMMEDIATELY PLACE THE SAFETY SELECTOR IN THE ON-SAFE POSITION. FAILURE TO FOLLOW THESE WARNINGS COULD RESULT IN SERIOUS INJURY OR DEATH. EVEN WITH THE BOLT OPEN AFTER SHOOTING, DO NOT ASSUME THE RIFLE IS UNLOADED. ALWAYS INSPECT THE CHAMBER, BARREL, FEED MECHANISM AND MAGAZINE TO BE CERTAIN THE RIFLE IS COMPLETELY UNLOADED. FAILURE TO FOLLOW THESE WARNINGS COULD RESULT IN SERIOUS INJURY OR DEATH. 14.
THE CHAMBER AND BARREL CAREFULLY TO BE SURE ALL LIVE CARTRIDGES ARE CLEARED FROM THE FIREARM. FAILURE TO FOLLOW THESE WARNINGS COULD RESULT IN SERIOUS INJURY OR DEATH. 15.1 UNLOADING THE RIFLE 1. Make sure the safety selector is in the on-safe position as explained in Section 9 and the muzzle is pointed in a safe direction. 2. Press the ambidextrous magazine release and REMOVE the magazine. 3.
16. BUTTSTOCK MODULE BEFORE PERFORMING STOCK ADJUSTMENT PROCEDURES, PLACE THE SAFETY SELECTOR IN THE ON-SAFE POSITION. REMOVE THE MAGAZINE, LOCK OPEN THE BOLT AS EXPLAINED IN SECTION 10.2 AND MAKE CERTAIN THE CHAMBER IS COMPLETELY UNLOADED. KEEP THE MUZZLE POINTED IN A SAFE DIRECTION. FAILURE TO FOLLOW THESE WARNINGS COULD RESULT IN SERIOUS INJURY OR DEATH. The FN SCAR 20S buttstock module has been designed for precision shooting typically done in the prone position.
16.2 ADJUSTING THE CHEEK REST HEIGHT To adjust the cheek rest height, press the cheek rest button (Figure 17) and push or pull the cheek rest up or down to the desired position (Figure 18). Raising the cheek rest will provide an additional 1.1” (28mm) of comb height. After adjusting the cheek rest to the desired setting, check to see that the cheek rest lock is fully engaged by pushing down on the cheek rest. FIGURE 17 FIGURE 18 Press and hold the check rest button. Move the check to the desired height.
MIL-STD 1913 rail slots are numbered for recording the location of sights and optics for future reference, if removed. Iron sights may also be mounted, if desired. Consult your dealer or a qualified gunsmith for mounting optical or iron sights that are commercially available. Ensure that once mounted they do not interfere with the normal operation of the rifle. Follow your optic’s instructions for mounting and ensure there is enough clearance between the ocular lens of the scope and your eye and face. 18.
19. DISASSEMBLY BEFORE PERFORMING DISASSEMBLY PROCEDURES, PLACE THE SAFETY SELECTOR IN THE ON-SAFE POSITION. REMOVE THE MAGAZINE, LOCK OPEN THE BOLT AS EXPLAINED IN SECTION 10.2 AND MAKE CERTAIN THE CHAMBER IS COMPLETELY UNLOADED. KEEP THE MUZZLE POINTED IN A SAFE DIRECTION. FAILURE TO FOLLOW THESE WARNINGS COULD RESULT IN SERIOUS INJURY OR DEATH.
2. Push in on the takedown pin from the left side (Figure 19) and pull it out to the right until it stops (Figure 20). FIGURE 19 FIGURE 20 Push in on the takedown pin from the left side. Pull the takedown pin to the right until it stops. IMPORTANT: The takedown pin is captive and cannot be removed completely from the trigger module. 3. Push the trigger module forward, releasing it from the backplate (Figure 21). 4. Pull down to remove the trigger module from the receiver (Figure 22).
19.2 REMOVAL OF THE BUTTSTOCK MODULE 1. Remove the magazine and make certain the rifle is completely unloaded and the safety selector is in the on-safe position as explained in Section 9. 2. Remove the trigger module as explained in Section 19.1. 3. Push the buttstock module downward and off of the receiver assembly backplate (Figure 23). FIGURE 23 Push the buttstock module off the receiver assembly. 19.3 REMOVAL OF THE MOVING PARTS ASSEMBLY 1.
4. With the moving parts assembly to the rear, pull out on the charging handle and remove it from the FIGURE 25 assembly (Figure 25). 5. Remove the return spring assembly by pulling it out toward the rear. 6. With the charging handle and return spring assembly removed, the entire moving parts assembly can be removed from the rear of the receiver by placing your hand Remove the charging handle.
19.4 DISASSEMBLY OF THE MOVING PARTS ASSEMBLY 1. Remove the magazine and make certain the rifle is completely unloaded and the safety selector is in the on-safe position as explained in Section 9. Make sure the bolt is forward on an empty chamber as explained in Section 10. 2. Remove the trigger module as explained in Section 19.1. 3. Remove the buttstock module as explained in Section 19.2. 4. Remove moving parts assembly as explained in Section 19.3. 5.
FIGURE 26 FIGURE 27 Use the charging handle to remove the firing pin retaining pin. Remove the firing pin. FIGURE 28 FIGURE 29 Remove the bolt cam pin. Remove the bolt.
19.5 REMOVAL OF THE GAS REGULATOR AND GAS PISTON 1. Remove the magazine and make certain the rifle is completely unloaded and the safety selector is in the on-safe position as explained in Section 9. Make sure the bolt is forward on an empty chamber as explained in Section 10. 2. Remove the trigger module as explained in Section 19.1. 3. Remove the buttstock module as explained in Section 19.2. 4. Remove moving parts assembly as explained in Section 19.3. 5.
9. Softly tap the piston and it will come out toward the front. NOTICE! DO NOT TAKE YOUR FIREARM’S ACTION APART BEYOND WHAT IS EXPLAINED IN THIS OWNER’S MANUAL. THIS IS A SPECIALIZED, FINELY-FITTED MECHANISM; ANY ATTEMPT TO DISASSEMBLE THE INNER MECHANISM MAY PERMANENTLY DAMAGE IT. IT IS UNNECESSARY, AND MAY DO DAMAGE TO THE INNER MECHANISM TO DISASSEMBLE IT FOR ROUTINE CLEANING AND OILING.
20.1 CLEANING PROCEDURES Your FN SCAR 20S will function more reliably and accurately over a longer period if it is properly maintained and kept clean. Clean your firearm after every day of shooting, and more often if it becomes excessively dirty during your shooting session. A minimum cleaning includes wiping down the firearm and lubricating key parts. Regular maintenance will also include cleaning the barrel and gas system.
If necessary, clean the chamber and locking lugs using a MIL-STD 7.62mm chamber brush. Properly apply military-grade cleaner/lubricant to the brush and insert it into the chamber. Rotate the brush in a clockwise direction several times and remove. 4. After all fouling has been removed, the chamber and bore should be wiped dry. When the bore is dry, pass a patch that is lightly lubricated with military-grade cleaner/lubricant through it for preservation. 5.
10. Wipe all exposed metal surfaces with a lightly oiled cloth making certain that all finger marks are removed. Finger marks provide a place where moisture can accumulate. The metal of the firearm should receive a light film of oil any time it has been exposed to weather or handling. 20.2 CLEANING THE TRIGGER MODULE The trigger module has been adjusted at the factory to provide a safe and consistent two-stage trigger pull.
NOTICE! DO NOT USE TOO MUCH LUBRICANT. EXCESSIVE LUBRICATION COULD INTERFERE WITH THE FUNCTION OF YOUR RIFLE. 20.3 CLEANING THE MAGAZINE WEAR EYE PROTECTION WHEN CLEANING THE MAGAZINE TO PREVENT SOLVENT, DEBRIS OR OTHER AGENTS FROM CONTACTING YOUR EYES, RESULTING IN INJURY. We do not recommend disassembling the magazine. Frequently inspect magazines to determine the need for cleaning as lubricant and dirt will gradually collect in the mechanism. 1.
21. ASSEMBLY 21.1 INSTALLATION OF THE GAS PISTON AND GAS REGULATOR NOTICE! DO NOT APPLY LUBRICANT TO THE GAS PISTON, GAS REGULATOR OR GAS BLOCK, THESE COMPONENTS ARE NOT TO BE LUBRICATED IN ANY WAY. USING LUBRICATION IN THE GAS SYSTEM COULD DAMAGE YOUR RIFLE. 1. Ensure that the notches in the gas rings of the piston are not aligned (Figure 33). 2. Insert the gas piston into the gas block with the gas rings towards the muzzle. 3.
21.2 ASSEMBLING THE MOVING PARTS ASSEMBLY 1. Insert the bolt into the front of the bolt carrier, ensure that the extractor is positioned on the right side (Figure 35). 2. Insert the bolt cam pin, ensuring the tab is horizontal (Figure 36). FIGURE 35 FIGURE 36 Install the bolt into the carrier. Install the bolt cam pin through the slot and into the bolt. 3. Insert the firing pin from the rear. 4. Insert the firing pin retaining pin until firmly seated.
21.3 INSTALLATION OF THE MOVING PARTS ASSEMBLY 1. Install the return spring assembly into the rear of the bolt carrier. Make certain that the narrow end of the guide rod retaining plate is up. 2. Ensure the upper portion of the bolt carrier is aligned with the bolt carrier guide rails inside the receiver frame and the bolt is fully forward in the bolt carrier (Figure 37). 3.
21.4 INSTALLATION OF THE BUTTSTOCK MODULE 1. FIGURE 39 Install the buttstock module by pressing in on the retaining plate and sliding the buttstock module on the backplate until seated (Figure 39). 21.5 INSTALLATION OF THE TRIGGER MODULE 1. Ensure that the takedown pin is pushed completely to the right of the trigger module (Figure 40). 2. Ensure that the hammer is cocked prior to re-installing the trigger module.
3. Place the trigger module into position, ensuring the rear extrusion engages the notch on the backplate at a slight angle (Figure 43). 4. Carefully rotate the trigger module into the receiver frame, pushing it to the rear (Figure 44). 5. Ensure the trigger module is fully seated to the rear before pushing the takedown pin to the left and securing the trigger module to the receiver assembly (Figure 45). FIGURE 43 Insert the trigger module rear first into the receiver.
21.6 FUNCTION CHECK Once the rifle has been reassembled, perform a function check to ensure proper reassembly. Before conducting the function check, verify that there is no ammunition present in the chamber of the rifle, in the magazine or located within the area of your work station. With your rifle pointed in a safe direction, 1. Operate the charging handle, making certain the bolt assembly moves freely. 2.
22. TAKING CARE OF THE RIFLE NOTICE! FN RECOMMENDS THAT YOUR RIFLE IS INSPECTED EVERY 5000 ROUNDS OR ONCE A YEAR BY A QUALIFIED GUNSMITH OR THE FN SERVICE CENTER BECAUSE DAMAGE, WEAR AND CORROSION ARE NOT ALWAYS VISIBLE FROM THE OUTSIDE. LAW ENFORCEMENT AND MILITARY PERSONNEL SHOULD CONTACT THEIR DEPARTMENTAL ARMORER WHO WILL INSPECT THE RIFLE ON A YEARLY BASIS. NOTICE! IF THE OPERATION OF THE RIFLE SEEMS ABNORMAL, REPORT IT TO THE FN SERVICE CENTER OR DEPARTMENTAL ARMORER IMMEDIATELY.
Excessively dirty ammunition may also require more frequent cleaning. Clean and lubricate your rifle after every use or if exposed to conditions that could adversely affect the finish or function of your rifle. In the case of intensive shooting, the rifle should be cleaned every 500 rounds. A minimum cleaning includes wiping down the rifle and lubricating key parts. It is important to keep your rifle clean and correctly lubricated.
23. WARRANTY, SERVICE AND TECHNICAL QUESTIONS Returning your firearm for service When returning your firearm for service, be sure to follow the guidelines below: NOTICE: ALL FFL HOLDERS, TO AVOID UNNECESSARY RETURN SHIPPING DELAYS PLEASE SUBMIT AN FFL WHEN A FIREARM IS SENT IN FOR SERVICE. 1. Complete the online sign-up form and register to request service via FN’s website, www.fnamerica.com. 2. Be sure your gun is completely unloaded. 3. Package it securely in a double-packed cardboard container. 4.
IMPORTANT: Any addition to your FN firearm of aftermarket accessories (such as suppressors, triggers, muzzle devices, stocks, etc.) is considered a modification of your firearm from its original configuration, which may void your warranty. We are unable to adapt each firearm for every variable effect that might occur when you install a third-party manufacturer’s accessory on an FN firearm.
24. TECHNICAL SPECIFICATIONS FN SCAR 20S Caliber Refer to your rifle’s barrel inscription as explained in Section 11 Length (in.) 40.6-42.5 Height (in.) 8 Width (in.) 2.7 Length of pull (in.) 13.25 - 15.0 Barrel Length (in.) 20 Twist Rate (in.) Refer to your rifle’s barrel inscription as explained in Section 11 Weight w/ Empty Magazine (lbs.) 11.2 lbs. Magazine Capacity 10-rounds (included) 20-rounds (available as an accessory) Trigger Pull (lbs.) 3.5 - 4.
NOTES 55
NOTES 56
NOTES 57
FNAMERICA.
