User Manual

W
ARING:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) T his devic e ma y n ot ca use h armful interference. ( 2) T his device must accept any interfer ence
received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comp ly with the limits for a Class B digital dev ice,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment ge nerates uses and can radiate r adio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause ha rmful interference to radio or televi sion reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
---Reorient or relocate the receiving antenna.
---Increase the separation between the equipment and receiver.
---Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
---Consult the dealer or an experienced radio/TV technician for help.
WARNING: Changes or modifications not expressly approved by the party responsible for comp liance
could void the user's authority to operate the equipment.
LABEL OF THE END PRODUCT:
The final end prod uct must be lab elled in a visible are a with the foll owing "Co ntains TX F CC ID:
2AATL-F11AMIM13-B1". If the size of the end product is smaller than 8x10cm, then additional FCC part
15.19 statement is required to be available in the users manual: This device complies with Part 15 of the
FCC Rules. Operati on is sub ject to the following two conditions: (1) this d evice may not cause harmfu l
interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
RF Exposure
This device has been eval uated and sho wn compli ant with the F CC R F Exposur e limits under fix ed
exposure c onditions ( antennas are greater than 20cm fro m a p erson's body) when i nstalled in certa in
specific OEM configurations.
IMPORTANT NOTE:
This device is intended only for OEM integrators under the following conditions:
(1) According to F CC Part 15 Subpart C Se ction 15.212, the rad io elements of the mod ular transmitter
must have the ir o wn s hielding. Ho wever, d ue to t here is no shiel ding for this W IFI/BT module, this
module is granted as a Limited Modular Approval.
(2) This modul e has be en d esigned to op erate with E xternal anten na（I-PEX connector ） havi ng a
maximum gain of 0dBi. The module is only certif ied with the installed antenna. An y change of the
antenna will void the certification.
(3) Integration is typically strictly restricted to Grantee himself or dedicated OEM integrators under control
of the Grantee . The modul e will be res ponsible to satisfy SAR/RF Exp osure req uirements, when the
module int egrated into any (portable, mob ile, fix ed) h ost device. T his modu le is int ended for OEM
integrator on ly and the OEM integr ators an d instructe d to ensure th at the e nd us er h as no ma nual
instructions to remove or install the device. T he OEM i ntegrator is still res ponsible for the FC C
compliance requirement of the end product, which integrates this module.
The module has no sh ielding an d tested s tand a lone. This modu le is te sted and ap proved as Limit ed
modular ap proval with stand alon e configuration, an y OE M incorpor ated this radio m odule into a ny
system are require additional testing and evaluation.
EU Regulatory Conformance
Hereby, we (F N-Link Technology Limited) d eclared that this device is in compliance with the essenti al
requirements and other relevant provisions of Directive 1999/5/EC.