// I NSTALLATION & USER INSTRUCTIONS NEW FOREST ELECTRIC FIRE © 2020 British Fires
// INSTALLATION & USER INSTRUCTIONS // 01 Section Contents 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 8.1 8.2 9.0 10.0 10.1 10.2 11.0 12.0 13.0 14.0 15.0 16.0 17.0 17.
// 1.0 IMPORTANT NOTES // 2.0 GROUNDING INSTRUCTIONS Important Notes Continued try to correct the interference by one or more of the following measures: Reorient or r elocat e t he receiving antenna.-- Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
// 4.0 COMPONENT CHECKLIST Quantity 1 1 1 1 1 1 1 1 1 2 2 4 2 12 8 8 Description Heater unit Wall bracket Remote control handset Box of logs Bag of slate Bag of bark Bag husk Bag of large crystals Bag of small crystals AAA batteries Blanking plates Small end trims Large end trims Firebox screws Wall plugs Fixing screws // 5.0 SITE REQUIREMENTS It should be noted that the appliance creates warm convected air currents.
// 8.0 INSTALLATION // 8.1 INSTALLATION – STUDWALL Stud wall installation British Fires assumes absolutely no responsibility for injuries and damages that may occur due to improper installation or handling. Remove any protective film coatings from the finished/decorative surfaces of the appliance, if any. After having selected the final position of the appliance taking into account the integrity of the wall the electric appliance may be secured to the wall.
// 8.1 INSTALLATION – STUDWALL Stud wall installation Continued Stud Wall *Non-combustible Appliance Header Header Header H W // One-sided (fully-recessed) installation Open Dimensions Height Width 22.4in 46.5in // 09 H W D Depth Width 11.8in 22.4in 46.5in W D // Two-sided installation Open Dimensions Height H D // Three-sided installation Depth Open Dimensions Height Width Depth 11.8in 22.4in 46.5in 11.
// 8.2 INSTALLATION – FLOATING Floating installation 8) With the appliance on the wall offer the floating shelf brackets to either sides of the appliance lining up all 8x holes on the floating bracket with the 8x holes on the side of the firebox. Then mark with a pencil through the hole in the end of the bracket against the wall. Before Installing the appliance onto the wall with the surround, secure the side trims each side of the appliance as described in section 9.0 Preparing the Appliance.
// 8.2 INSTALLATION – FLOATING // 9.0 PREPARING THE APPLIANCE Floating installation continued For a two or three-sided installation Firebox screws For a two-sided installation, add one of the blanking plates and secure with the six firebox screws into position. Next add the two small trims and the large trim to the side of the appliance. Then line the holes of the trims with the corresponding holes of the firebox and screw into position with the six countersunk screws, previously removed.
// 10.0 FOREST VIEW FUEL BED LAYOUT Forest View 1 4 Taking a small account of the small crystals, scatter randomly over the Use the slate pieces and place these randomly on the bed as shown in frosted base as shown above. image 4, above. PRO TIP – Use the small crystals to pick up extra light from the fuel bed to give you the best effect. 2 5 Use the contents from the Forest terrain bag and place this in the formation shown above (image 2) towards the front and sides of the frosted base.
// 10.1 SLATE VIEW FUEL BED LAYOUT Slate View 1 2 3 Evenly scatter the small crystals over the frosted base as shown in image 1, left. The crystals should be spread out across the whole base and form a layer covering the whole area. Take the two types of the slate effect pieces and spread these evenly throughout, on top of the bed of crystals. Place the logs on top of the base layer created by the crystals and slate pieces. Position them as shown in image 3.
// 10.2 DIAMOND LIGHT VIEW FUEL BED LAYOUT Three Diamond Light colour settings Diamond light View 1 2 // 19 Evenly scatter the small crystals over the frosted base as shown in image 1, left. The crystals should be spread out across the whole base and form a layer covering the whole area. Take the larger crystals and place these in position as shown in image 2, left. For the best results, remove a small amount of the small crystals and place the larger crystal directly on the frosted base.
// 11.0 PAIRING THE REMOTE CONTROL // 12.0 OPERATING THE APPLIANCE Pairing the remote control Within 1 minute of turning the power on by the main ON/OFF switch (located on the front, top right hand side of the appliance), press and hold and the and buttons on the remote control for 3 seconds, to remotely pair to the appliance, the LCD only displays bL (displayed at the display temperature position) and flashes 5S, then returns to the current display state. The remote is then paired to the appliance.
// 12.0 OPERATING THE APPLIANCE Continued Standby Button: When powering up for the first time, press the “on/off switch” on the fire. The default parameters of the system are: the heating gear position is “82°F/27°C”, the main flame gear position is L1 (Orange), no heating. Changing Flame Effect: In the power-on state, press this button, the digital screen displays the flame position and the flame indicator is bright, and the main flame position can be adjusted.
// 12.0 OPERATING THE APPLIANCE // 13.0 SAFETY CUT-OUT SYSTEM // 14.0 CLEANING AND MAINTENANCE Continued Heat settings: Use remote control’s Heater button to select the temperature. The system default parameters are: 82°F/80°F. Press & buttons to select the temperature when the heating is turned on. Temperature range: 62°, 63°, 64°, 65°, 66°, 67F, 68°, 69°, 70°, 71°, 72, 73°, 74°, 75°, 76°, 77°, 78°, 79°, 80°, 81°, 82°F.
// 15.0 TROUBLESHOOTING GUIDE My Wall Inset Electric Fire... Remedy Is not switching on Ensure mains switch is on. Replace the fuse in the plug. Is not emitting any heat The fire is fitted with an energy saving thermostat. If the temperature in the room is higher than the temperature selected on the fire, then the thermostat will stop the heater from turning on.
// 16.0 APPLIANCE DIMENSIONS // 17.0 GUARANTEE AND TERMS & CONDITIONS AUTOMATIC 1-YEAR GUARANTEE A // APPLIANCE DIMENSIONS (in.) A: B: C: D: B E C D 47.2 in 12.2 in 46.4 in 0.5 in E: F: G: H: 0.5 in 11.7 in 16.7 in 22.1 in F We offer a standard one-year guarantee on every electric appliance.
// NOTES // 31 © 2020 British Fires // 32
// NOTES // 33 © 2020 British Fires // 34
This appliance is only suitable for well insulated spaces or occasional use. Please note: Except where otherwise stated, all rights, including copyright in the text, images and layout of this booklet is owned by British Fires. You are not permitted to copy or adapt any of the content without the prior written permission of British Fires. © 2020 British Fires // 35 Models covered by these instructions: New Forest Electric Fire (EF40-48B) US Patent Application No. US 16/710.