Instruction Manual

ManualsBrandsFocalcrest ManualsElectronicsSmart Relay

Adding to your Zigbee network (Inclusion)

Operating Instructions

Set your Zigbee 3.0 gateway into inclusion/pairing mode

(Refer to the gateway’s manual)

Set the Smart Relay into inclusion/pairing mode with

either methods. The LED will slowly blink blue for 30

seconds.

a. Short press the RESET button.

b. (Alternative) If the Smart Switch installed too, quickly

toggle the mechanical switch panel over 10 times

If the Smart Relay is successfully paired, the LED will be

solid blue.

Removing from Zigbee network (Exclusion)

Remove the Smart Relay from your Zigbee 3.0 gateway

Press and hold the RESET button for more than 5 seconds.

If the Smart Relay is removed, the LED will be solid red.

Resetting to factory defaults

Press and hold the RESET button for more than 5 seconds.

If the LED light is solid RED, the Smart Relay has been

factory reset and all data have been cleared.

Indicator Light Status

Description Indicator Light Status

Pairing mode

The BLUE LED blinks slowly for

30 seconds

Normal Zigbee network

working mode

No Zigbee network

working mode

The BLUE LED is always on

The RED LED is always on

Switch operation

The BLUE LED blinks once

2. EXCLUSIONS NOT COVERED BY THIS LIMITED

WARRANTY.

This Limited Warranty does not cover, and Focalcrest and its

suppliers are not responsible for:

(A) Damage, malfunction, or inoperability of the Focalcrest

Product caused by: DEALER RECOMMENDED OR

CERTIFIED BY Focalcrest.

shippers or delivery services, or due to Customer

improperly opening the Focalcrest Product packaging;

Operation, storage, or application of the Focalcrest

Product outside of the environmental, temperature, and

other specifications provided in the Documentation;

Acts of God, including, but not limited to, flood, fire,

earthquake, lightning, electrical surges, or any other

external cause;

Any act beyond Focalcrest’s direct control, including,

but not limited to, unauthorized repair or installation by

Customer or 3rd party, accident, abuse, misuse, neglect,

use of incompatible devices and accessories, operating

the Focalcrest Product outside the permitted or intended

uses provided in the Documentation, or any other reason

besides a defect in material or workmanship;

Use of incorrect voltage lines, fuses, circuit breakers, or

incompatible load types as set forth in the Documenta-

tion, or failure to provide adequate, continuous,

compatible power to the Product, if applicable;

Interference from radio frequencies, infrared sources, or

obstacles;

Normal wear and tear, or failure to install, maintain,

or repair the Focalcrest Product in accordance with the

Documentation and the applicable provisions of law for

the jurisdiction where the Focalcrest Product is being

installed;

Any product, part or software that has been modified to

alter functionality or capability without the express written

permission of Focalcrest;

Batteries and consumable parts (if any), unless damage

occurred due to a defect in materials or workmanship in

the Focalcrest Product;

Cosmetic damage, including, but not limited to,

scratches, dents and normal wear and tear;

Focalcrest Product in which the serial number has been

removed or defaced; and

ANY DAMAGE, MALFUNCTION, OR INOPERABILITY

ARISING FROM INSTALLATION, MAINTENANCE, OR

PROGRAMMING PERFORMED BY AN INDEPENDENT

CONTRACTOR, INCLUDING, WITHOUT LIMITATION, ANY

Thank you for purchasing In-Wall Relay Switch.

Focalcrest Limited values your business and always strives

to provide you the very best quality of service.

1. HARDWARE PRODUCT LIMITED WARRANTY.

Focalcrest warrants to the original end user purchaser,

(“Customer”) of each new Focalcrest product that such

Focalcrest Product hardware and components (“Product

Hardware”), when used in accordance with the technical

specifications by Focalcrest, will be free, in all material

respects, of defects in materials and workmanship under

normal use (“Limited Warranty”). This Limited Warranty

is non-transferable and sets forth Focalcrest’s sole and

exclusive liability, and the sole and exclusive remedies

available in relation to any non-conformity, defect or similar

claim.

Warranty Policy

Focalcrest Limited Warranty

(B) any on-site labor costs incurred by Customer for the

diagnosis, removal, repair, re-installation, and/or

reprogramming of the Focalcrest Product;

of 3rd party products controlled or automated by Focalcrest

Products or Software (a “Focalcrest System”), batteries or

software product (manufacturers, suppliers, or publishers,

other than Focalcrest may provide their own warranties

to Customer for their products, but Focalcrest, insofar as

permitted by law, provides non-Focalcrest Products only

“AS IS”); and

(D) the cost of repairing or replacing, or compensation for,

any property that is damaged when a Focalcrest Product

does not work properly, even if the damage was caused by

a Focalcrest Product.

equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Consult the dealer or an experienced technician for help.

This de

vice complies with part 15 of the FCC rules. Operation

is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2)

this device must accept any interference received, including

interference that may cause undesired operation.

Changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to

operate the equipment.

NOTE:

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential

installation.

This equipment generates uses and can radiate radio

frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that

interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or

television reception, which can be determined by turning the

FCC ID: 2AYEW-SRB01

FCC Statement

Certifications (regional):

(

)

(

)

(iii)

(

)

(

)

(

)

(vii)

(viii)

(

)

(

)

Rev. A-031821 P/N SRB01

(xi)

(xii)

Important Announcement Important Note

Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits

set forth for an uncontrolled environment. This equipment

should be installed and operated with minimum distance

20cm between the radiator and your body.

This transmitter must not be co-located or operating in

conjunction with any other antenna or transmitter.

Disposal Instructions:

This symbol on the product or on its packaging indicates

that this product must not be disposed of with your other

household waste. Instead, it is your responsibility to dispose

of your waste equipment by handing it over to a designated

collection point for the recycling of electrical and electronic

equipment waste.

This equipment complies with FCC ad1ation exposure l1m1ts set

forth for an uncontrolled environment. This equipment should

be installed and operated with minimum distance 20cm

between the radiate and your body This t ansmitte must not be

co-located or ope ating in con丿unction with any other antenna

or transmitter