Assembly Instructions User Manual

ASSEMBLY INSTRUCTIONS

Item# FAKDBR20 and FAKDBR12 | Aluminum Bakery Rack

FOODSERVICE, LLC

Part Side Panels 1" diameter Rods

/4" diameter Rods Casters 1

/8" Screws U-Brackets 2" Screws

Qty 2 2 4 4 8 8 4

Step 1 Unpack carton, identify & conﬁrm quantity of components.

Step 2 Insert casters into openings at the bottom of the side panel, see Diagram #1. Make sure that hole in

caster stem is aligned with hole in side panel opening.

Step 3 Align threaded opening in 1" diameter rod with opening of inside side panel. Thread 2" screw through the

side panel opening and into threaded opening of 1" diameter rod and loosely tighten. See Diagram #2.

Make sure screw head is on the the outside of the side panel.

Step 4 Repeat Step 3 for other 1" diameter rod.

Step 5 Insert

/4" diameter rod into inside side panel opening.

Step 6 Align opening in U-bracket with the opening in the outside of the side panel, see Diagram #3.

Step 7 Thread 1

/8" screw through U-bracket and into

/4" diameter rod and loosely tighten, see Diagram #4.

Step 8 Repeat steps 5 through 7 for other 3

/4" diameter rods.

Step 9 Place side panel on ground with insert rods facing up.

Step 10 Place other side panel on top of side panel on the ground so that rods ﬁt into side panel openings.

Step 11 Insert casters into openings at the bottom of side panel (follow step 2).

Step 12 Thread 2" screw through the side panel opening and into threaded opening of 1" diameter rod and

loosely tighten. See Diagram #2.

Step 13 Repeat step 12 for the other caster.

Step 14 Align opening in U-bracket with the opening in the outside of the side panel, see Diagram #3.

Step 15 Thread 1

/8" screw through U-bracket and into smaller diameter rod and loosely tighten, see Diagram #4.

Step 16 Repeat steps 14 & 15 for other 3 U-brackets.

Step 17 Stand unit upright and tighten all screws.

PAGE 1
ASSEMBLY INSTRUCTIONS Item# FAKDBR20 and FAKDBR12 | Aluminum FOODSERVICE, LLC Step 1 Unpack carton, identify & confirm quantity of components. Step 2 I nsert casters into openings at the bottom of the side panel, see Diagram #1. Make sure that hole in caster stem is aligned with hole in side panel opening. Step 3 lign threaded opening in 1" diameter rod with opening of inside side panel.
PAGE 2
ASSEMBLY INSTRUCTIONS Diagram 1 Diagram 2 Diagram 3 Diagram 4 Call Customer Service at 1.800.968.3918 | Fax 1.800.968.4129 www.focusfoodservice.com FOODSERVICE, LLC rev.
PAGE 3
INSTRUCCIONES DE ENSAMBLAJE Artículo No. FAKDBR20 y FAKDBR 12 | Bastidor de Aluminio para Panaderías SHELVING Paso 1 Desempaque la caja de cartón e identifique y confirme las cantidades de los componentes en la misma. Paso 2 Inserte las ruedas locas dentro de las aberturas en la parte inferior del panel lateral (vea el Diagrama No. 1). Asegúrese de que el agujero en el vástago de la rueda loca esté alineado con el agujero en la abertura del panel lateral.
PAGE 4
INSTRUCCIONES DE ENSAMBLAJE Diagrama 1 Diagrama 2 Diagrama 3 Diagrama 4 Llame a Atención al Cliente por el 1.800.968.3918 | Fax 1.800.968.4129 www.focusfoodservice.com FOODSERVICE, LLC rev.