Installation Instructions

ManualsBrandsFolger Adam ManualsElectronicsFail Secure Electric Strike for Concealed Vertical Rod in Satin Aluminum

Folger Adam 310-6-1, -2, -3, -8, -30 Series Electric Strike

HES, Inc.

22630 N. 17th Ave.

Phoenix, AZ 85027

800-626-7590

www.hesinnovations.com

Product Components

Electric Strike Body & Faceplate

Plug In Connectors*

#12-24 x 1/2” Mounting Screws

Electrical Specifications

ELECTRICAL RATINGS FOR SOLENOID*

MINIMUM WIRE GAUGE REQUIREMENTS

SOLENOID VOLTAGE

CONTINUOUS DUTY

12VDC

23.5

.51

24VDC

.25

Resistance in Ohms

Amps

Solenoids are rated at +/- 10% indicated value.

*Resistance value indicated above is per coil.

200 feet or less

200 - 300 feet

300 - 400 feet

18 gauge

16 gauge

14 gauge

18 gauge

16 gauge

*Only 1 Plug In Connector is used with 310-6-30

Summary of content (8 pages)

PAGE 1
HES, Inc. 22630 N. 17th Ave. Phoenix, AZ 85027 800-626-7590 www.hesinnovations.com Installation Instructions Folger Adam 310-6-1, -2, -3, -8, -30 Series Electric Strike Product Components 1 Electric Strike Body & Faceplate 2 #12-24 x 1/2” Mounting Screws 3 Plug In Connectors* *Only 1 Plug In Connector is used with 310-6-30 1 2 3 Electrical Specifications ELECTRICAL RATINGS FOR SOLENOID* MINIMUM WIRE GAUGE REQUIREMENTS 12VDC 24VDC 23.5 .
PAGE 2
Installation Directions 2 CAUTION! Before connecting any device at the installation site, verify input voltage using a multimeter. Many power supplies and low voltage transformers operate at higher levels than listed. Any input voltage exceeding 10% of the solenoid rating may cause severe damage to the unit and will void the warranty. Prepare Strike Finish Installing 1. If using the LCBMA (Latchbolt monitor & Locking Cam Monitor), see Diagram 1 for wiring instructions. 2.
PAGE 3
Cutout Templates 3 Inches [mm] 310-6-1 Template & Dimensions 6-15/16” [176.20] 4-3/4” [120.65] 6-15/16” [176.20] 4-3/4” [120.65] 4-3/8” [111.13] 1-3/8” [34.93] 1/8” [3.18] 1” [25.4] 11/16” 2” (Typ.) [17.45] [50.8] 1-1/4” [31.75] 14-1/2” [368.55] 13-7/8” [352.43] 5/16” [8.13] 13-25/64” [340.10] CL CL 13/16” [20.62] 1-5/8” [41.40] Reinforce jamb for tapped holes 10 gauge minimum [2 places] 1-3/8” [34.93] 14-1/2” [368.30] 5/8” [15.87] 1-3/4” [44.45] 5-1/16” [128.59] 1-5/8” [41.
PAGE 4
Cutout Templates 4 Inches [mm] 310-6-2 Template & Dimensions 7-1/4” [184.15] 7-1/4” [184.15] 5” [127] 4-3/4” [120.65] 4-3/4” [120.65] 1-3/8” [34.93] 1/8” [3.18] 11/16” 2” (Typ.) [17.45] [50.8] 1” [25.4] 1-1/4” [31.75] 15-9/64” [384.56] 5/16” [8.13] 14-1/2” [368.30] 13-25/64” [340.10] CL CL 13/16” [20.62] 1-5/8” [41.40] Reinforce jamb for tapped holes 10 gauge minimum [2 places] 1-3/8” [34.93] 15-1/8” [384.18] 5/8” [15.87] 1-3/4” [44.45] 5-1/16” [128.59] 1-5/8” [41.28] #16 Drill [.
PAGE 5
Cutout Templates 5 Inches [mm] 310-6-3 Template & Dimensions 7-9/16” [192.07] 7-9/16” [192.07] 5-5/8” [142.88] 4-3/4” [120.65] 4-3/4” [120.65] 1-3/8” [34.93] 1/8” [3.18] 11/16” 2” (Typ.) [17.45] [50.8] 1” [25.4] 1-1/4” [31.75] 15-25/64” [400.30] 5/16” [8.13] 15-1/8” [384.18] 13-25/64” [340.10] CL CL 13/16” [20.62] 1-5/8” [41.40] Reinforce jamb for tapped holes 10 gauge minimum [2 places] 1-3/8” [34.93] 15-3/4” [400.05] 5/8” [15.87] 1-3/4” [44.45] 5-1/16” [128.59] 1-5/8” [41.
PAGE 6
Cutout Templates 6 Inches [mm] 310-6-8 Template & Dimensions 9” [228.60] 4-3/4” [120.65] 1-3/8” [34.93] 11/16” [17.45] 1/8” [3.18] 4-3/4” [120.65] 1-3/16” [30.23] 1” [25.4] 2” (Typ.) [50.8] 12” [304.8] 10-5/32” [258.06] 9-1/2” [241.3] 1/3” [8.38] 9” [228.6] CL 13/16” [20.62] 1-5/8” [41.40] #16 Drill [.177] & tap 12-24 U.N.C. thru [5 places] Center line of electric strike & latchbolt of lock must align. Reinforce jamb for tapped holes 10 gauge minimum [2 places] 5/8” [31.75] 1-3/4” [44.
PAGE 7
Cutout Templates 7 Inches [mm] 310-6-30 Template & Dimensions 6-1/4” [158.75] 6-1/4” [158.75] 3” [76.20] 4-3/4” [120.65] 4-3/4” [120.65] 1-3/8” [34.93] 1/8” [3.18] 11/16” 2” (Typ.) [17.45] [50.8] 1” [25.4] 1-1/4” [31.75] 13-1/8” [333.76] 12-1/2” [317.50] 5/16” [8.13] 13-25/64” [340.10] CL CL 13/16” [20.62] 1-5/8” [41.40] Reinforce jamb for tapped holes 10 gauge minimum [2 places] 1-3/8” [34.93] 13-1/8” [333.38] 5/8” [15.87] 1-3/4” [44.45] 5-1/16” [128.59] 1-5/8” [41.28] #16 Drill [.