Horizon™ Icemaker Installation Instructions for Ice Storage Bin Top-mount Applications HCC/HMC/HCE/HME1000ABT, HCC/HMC/HCE/HME1400ABT, HCC/HMC/HCE/HME1000WBT, HCC/HMC/HCE/HME1400WBT (See model number configurator on page 2 for details.) Order parts online www.follettice.
Chewblet® Ice Icemaker Model Number Configurations HC Icemaker MC Maestro Chewblet (400 Series) HC Horizon Chewblet (1000, 1400, 1650 Series) HM Horizon Micro Chewblet 2 Voltage C 1000 A Series C 208-230/60/1 (icemaking head) 400 up to Self-contained only. 454 lbs D 115/60/1 (icemaking head) (206kg) 1000 up to Self-contained and remote. 1036 lbs If remote unit, high side is (471kg) 208-230/60/1. 1400 up to E 230/50/1 (icemaking head) Self-contained only.
Read and complete the following 8 installation steps Unpack Site preparation 1 2 Bin preparation Louvered docking assembly 3 4 Ice transport tube External connection 5 6 Internal connection Front cover 7 BIN • TOP-MOUNT 8 self-contained 3
Unpack Carefully unpack and inspect the contents of your Follett icemaker. 1.
Site preparation Prepare the installation site. 2 Provide drainage, water supply and electrical power to within 6 feet (2m) of icemaker in accordance with local and national codes. Outdoor installation is not recommended and will void warranty. 2.1 2.
Bin preparation Prepare the bin. 3.1 Bin top preparation 3.
Louvered docking assembly Install the louvered docking assembly. 4 WARNING • Docking station must be secured in accordance with these instructions to ensure icemaker stability. • Ventilation openings in the louvered docking station should be clear of obstruction 4.
Ice transport tube Install the ice transport tube. 5.
External connections Connect utilities to louvered docking assembly. 6.1 Air-cooled icemakers only 6.2 Water-cooled icemakers only ➋ ➌ ➋ ➍ ➊ ➊ • Remove access panel if necessary • Install drain line ➊ The rigid drain line from the icemaker must have at least 1/4" per foot pitch (6,4mm/0,3m) • Install icemaker potable water supply ➋ • Replace access panel BIN • TOP-MOUNT self-contained 6 • Remove access panel if necessary • Install drain line ➊.
Internal connections Connect icemaker to louvered docking assembly. 7 CAUTION • Plug must be accessible after final installation. • H_E1400A/W 230/50/1) requires a 20 amp circuit (4.00 mm2 wire) Air-cooled icemakers – follow steps 7.1 through 7.4. 7.1 Ice transport tube 7.
Water-cooled icemakers – follow steps 7.5 through 7.10. 7.5 7.6 Cooling lines Ice transport tube ➋ Out In ➊ • Install icemaker cooling water lines to louvered docking assembly • Slide icemaker into louvered docking assembly ➊ • Insert ice transport tube into coupling and tighten nut firmly ➋ 7.7 7.8 Potable water and drain lines Cooling lines and power ➊ ATTENTION INSTALLER Valve is preset at factory. Do not adjust. Adjustment will void warranty and may damage equipment.
7.9 Power cord • Remove twist tie • Carefully pass plug thru opening and plug into wall outlet 12 7.
Front cover Install front cover to icemaker. 8.1 8 Install front cover ➋ ➊ • Slide icemaker cover over machine ensuring that tabs on back of cover slip under louvers on back of louvered docking assembly ➊ • Insert and tighten two screws through cover and into louvered docking assembly ➋ NOTICE Icemaker MUST be sanitized prior to operation! Consult Operation and Service Manual provided with icemaker for sanitizing instructions.
self-contained BIN • TOP-MOUNT
BIN • TOP-MOUNT self-contained 15
801 Church Lane • Easton, PA 18040, USA Toll free (877) 612-5086 • +1 (610) 252-7301 www.follettice.