Horizon™ Ice Machine Models with RIDE™ Technology Installation Instructions for Ice Storage Bins HCD/HMD/HCF/HMF1000RBS, HCD/HMD/HCF/HMF1400RBS, HCD/HMD/HCF/HMF1650RBS HCD/HMD1000NBS, HCD/HMD1400NBS, HCD/HMD1650NBS (See model number configurator on page 2 for details.) Order parts online www.follettice.com remote condensing NO PART E SINGL PHASE OZ HZ PSIG E CHARG SIDE LOW L MODE IN MADE USA THE NSF UL R UL C R AMPS AMPS 208264 Stock Module Identification Plate Module No.
Chewblet® Ice Machine Model Number Configurations HC Icemaker MC Maestro™ Chewblet® (400 Series) HC Horizon Chewblet (1000, 1400, 1650 Series) HM Horizon Micro Chewblet Voltage C 1400 A Series 400 up to C 208-230/60/1 (icemaking head) Self-contained only. 454 lbs D 115/60/1 (icemaking head) (206kg) Self-contained and remote. If remote 1000 up to unit, high side is 208-230/60/1. 1036 lbs E 230/50/1 (icemaking head) (471kg) Self-contained only.
Read and complete the following 8 installation steps Unpack Site preparation 1 2 Bin preparation Louvered docking assembly 3 4 Ice transport tube External connection 5 6 Internal connection Front cover 7 BIN • RIDE Technology 8 self-contained 3
Unpack Carefully unpack and inspect the contents of your Follett ice machine. 1.
Site preparation Prepare the installation site. 2 Provide drainage, water supply and electrical power to within 6 feet (2m) of ice machine in accordance with local and national codes. Outdoor installation of low side is not recommended and will void warranty. 2.1 2.1 Installation site requirements ➎ 3/8" ∅ (9,5mm) ➍ NO PART E SINGLE PHAS OZ HZ PSIG GE CHAR SIDE L MODE IN MADE USA THE LOW NSF UL R UL C R AMPS AMPS Stock Module Identification Plate Module No. Product Service No.
Bin preparation Prepare the bin. 3.1 3.2 Bin top preparation 3 Bin top preparation 3" ∅ (76,2mm) CL CL • Locate center of bin top • Cut 3" (77,2mm) diameter hole in bin top 3.
Louvered docking assembly Install the louvered docking assembly. Wall bracket accessory 4 Machine stand accessory • Mount louvered docking assembly to machine stand accessory • Mount louvered docking assembly to wall bracket accessory 2.1 4.
Transport tube Install the ice transport tube. 5.1 5 Ice transport tube installation ➍ ➏ ➐ ➋ Hot Water 160 F (71 C) ➊ ➑ ➎ ➒ 1/4" ➌ ➓ 1' Ice transport tube tips • Insulate entire length of ice transport tube ➊ • Secure ice transport tube ➋ as needed to prevent dips and traps from forming. For long tube runs see guide on page 13. • Pitch ice transport tube at least 1/4" per foot (6,4mm/.
External connections Connect utilities to louvered docking assembly. 6.1 6.2 Water and drain ➋ 6 Refrigerant ➊ ➊ • Remove access panel if necessary. • Install drain line ➊. The rigid drain line from the ice machine must have at least 1/4" per foot pitch (6,4mm/0,3m).
Connect louvered docking assembly to ice machine. 7.1 Ice transport tube installation 7.2 Internal connections 7 Water and drain lines ➊ ➋ ➋ ➊ ➋ ➊ • Slide ice machine into louvered docking assembly ➊ • Insert ice transport tube all the way into coupling and tighten nut firmly ➋ • Insert potable water line into valve • Push drain line over hose barb on back of evaporator mount ➋ 7.3 7.
7.
Front cover Install front cover to ice machine. 8.1 8.
Long tube run recommendations ➊ max. 2 ft (.6m) ➋ 1/4" 1' • Pitch ice transport tube to allow melt water to drain towards ice machine ➊ • Secure insulated ice transport tube at least every 2 ft (.
self-contained BIN • RIDE Technology
BIN • RIDE Technology self-contained 15
Horizon, Maestro, Harmony, Ice Manager, SafeCLEAN, Sani-Sponge, RIDE and Vision are trademarks of Follett Corporation. Chewblet is a registered trademark of Follett Corporation, registered in the US. 801 Church Lane • Easton, PA 18040, USA Toll free (877) 612-5086 • +1 (610) 252-7301 www.follettice.
