Installation Instructions

ManualsBrandsFollett ManualsCommercial EquipmentClaris Hardness Removal Filtration System

Order parts online:

www.follettice.com

00986109R00

801 Church Lane • Easton, PA 18040, USA

Toll free (877) 612-5086 • +1 (610) 252-7301

www.follettice.com

Installation Instructions

Claris Filter for 7 Series Dispensers

P/N 00986059

Materials Supplied

(1) Claris  lter

(1) Head assembly

(1) Bracket

(1) Elbow  tting

(2) Bushings

(6) Screws, M5 x 12

(2) Nuts, M5 x 1mm

(20 ft.) Tubing, 1/4" OD x 0.170" ID

CAUTION!

Only quali ed technicians should

attempt to service or maintain this

equipment.

If you experience any problems during

the installation process, please call Follett

Technical Service toll-free at (877) 612-5086 or

+1(610)252-7301 for assistance.

Installation

1. Turn off water supply to dispenser.

2. Mount bracket and head assembly

(Fig.1). (Bracket shown mounted within

base, right-hand side, of freestanding

unit.)

Fig. 1

Head

Assembly

Drain

Valve

Water

Out

Water

FRONT VIEW

Summary of content (4 pages)

PAGE 1
Claris Filter for 7 Series Dispensers P/N 00986059 Installation Instructions Materials Supplied Fig. 1 (1) Claris filter (1) Head assembly (1) Bracket Head Assembly (1) Elbow fitting (2) Bushings (6) Screws, M5 x 12 (2) Nuts, M5 x 1mm (20 ft.) Tubing, 1/4" OD x 0.170" ID CAUTION! Only qualifi ed technicians should attempt to service or maintain this equipment.
PAGE 2
3. Press and hold the maintenance/clean switch (Fig. 2.1) displays in the user interface (Fig. 2.2). until Fig. 2 4. Remove (unscrew) chrome ice dispenser chute (Fig. 2.3). 2 5. Remove the drip tray (Fig. 2.4). 6. Remove the two screws (Fig. 2.5) on the front panel (behind the drip tray). 7. Remove and set aside the front panel (Fig. 2.6) - do not disengage the plug on the back of the User Interface or the tubing at the water dispenser chute (if so equipped). 1 8.
PAGE 3
10. Disconnect water tube at T-fitting (Fig. 3.1) and connect elbow fitting to water tube (Fig. 3.2). Fig. 3 Water Reservoir Water Chute (optional) 2 1 Water Supply 11. Place bushings in two hole locations in back panel (Fig. 4.1). Water Solenoid Valve (optional) Fig. 4 12. Cut 5 ft. of tubing and connect one end to Claris 'water in' (Fig. 4.2). 13. Run tubing through bottom bushing and connect to T-fitting (Fig. 4.3). 14. Cut 5 ft. of tubing and connect one end to Claris 'water out' (Fig. 4.
PAGE 4
15. Place end of tube attached to head assembly into 3.5 gallon capacity bucket (Fig. 5.1). Fig. 5 2 Closed 16. Locate screw at head assembly drain valve (Fig. 5.2) and turn clockwise to open drain valve. Open 17. Turn on water supply and run 3 gallons of water through Claris filter into bucket. 1 18. Turn head assembly drain valve screw (Fig. 5.2) counterclockwise to close drain valve. 19. Lift bypass select knob (Fig. 6.1) and turn to set the appropriate filter bypass level (Fig. 6.