Installation Instructions for Remote Condensing Unit

ManualsBrandsFollett ManualsCommercial Equipment23" Horizon Elite Series Remote Condenser Ice Machine with 2039 lbs. Daily Ice Production, RIDE Technology, Chewblet Ice, and Agion Silver-Based Antimicrobial in Stainless Steel

REMOTE CONDENSING UNIT

Order parts online

www.follettice.com

Horizon Elite

™

Ice Machine Installation Instructions

for Remote Condensing Unit

HC_1810R/N, HM_1810R/N

HC_2110R/N, HM_2110R/N

01157932R01

801 Church Lane • Easton, PA 18040, USA

Toll free (877) 612-5086 • +1 (610) 252-7301

www.follettice.com

Vision™ Remote Condensing

RIDE remote ice delivery equipment

Drop-in Remote Condensing

RIDE

remote ice delivery equipment

Bin Remote Condensing

Top Mount

Harmony™ Remote Condensing

RIDE remote ice delivery equipment

Bin Remote Condensing

RIDE remote ice delivery equipment

Harmony Remote Condensing

Top Mount

Summary of content (12 pages)

PAGE 1
Horizon Elite™ Ice Machine Installation Instructions for Remote Condensing Unit HC_1810R/N, HM_1810R/N HC_2110R/N, HM_2110R/N Order parts online www.follettice.com Drop-in Remote Condensing RIDE® remote ice delivery equipment Vision™ Remote Condensing RIDE remote ice delivery equipment REMOTE CONDENSING Harmony Remote Condensing Top Mount Harmony™ Remote Condensing RIDE remote ice delivery equipment 801 Church Lane • Easton, PA 18040, USA Toll free (877) 612-5086 • +1 (610) 252-7301 UNIT www.
PAGE 2
Condensing Unit Shipping Weight Model Single-phase 3-phase Horizon 1810 Horizon 2110 305 lb (1139 kg) 305 lb (1139 kg) 305 lb (1139 kg) 305 lb (1139 kg) Prior to installation, carefully unpack and inspect the contents of your condensing unit! Site preparation 1 To ensure proper performance, ease of service and warranty coverage, it is critical that you follow the requirements detailed in this manual. If you cannot meet these requirements or have questions, call our technical service group at 877.
PAGE 3
2.1 1.2 Condenser installation specifications 75' max. (22.8 m) ➊ CONDENSER UNIT ➍ maximum line rise ➋ P-trap required S-trap required ➊ +35' (+10.7 m) +20' (+6.1 m) P-trap required Easton Pennsylvania CORPORATION MODEL PART NO SERIAL NO FULL LOAD AMPS VOLTS HZ SINGLE PHASE MOTOR COMPRESSOR THERMALLY PROTECTED REFRIGERANT CHARGE DESIGN PRESSURE HIGH SIDE Stock Module Identification Plate Module No. Product OZ LOW SIDE PSIG 208264 MIN. BRANCH CIRCUIT AMPACITY AMPS MAX.
PAGE 4
Condenser installation 2.1 2 Install condensing unit • Level unit • Securely attach base of unit using holes found in base plate • Required rack system capacity at 0 F (–18 C) evaporator (EPR supplied by installer). 1810N: 15,700 Btu/hr (3956 kcal/hr) 2110N: 18,200 Btu/hr (4586 kcal/hr) 2.2 Electrical requirements Condensing unit 1810 Single-Phase Electrical 1810 3-Phase 2110 Single-Phase 2110 3-Phase 208-230V, 60Hz Max Circuit HVACR breaker size Min Circuit Ampacity 45A 25A 45A 30A 26.
PAGE 5
2.3 Single-phase condensing unit wiring diagram 208-230V/1/60Hz (Danfoss MTZ36-1AV) MOP = 45; MCA = 26.2 (Danfoss MTZ44-1AV) MOP = 45; MCA = 27.
PAGE 6
2.3 3-phase condensing unit wiring diagram 208-230V/3/60Hz (Danfoss MTZ36-3AV) MOP = 25; MCA = 15.7 (Danfoss MTZ44-3AV) MOP = 30; MCA = 19.
PAGE 7
2.4 Phase monitor adjustments (if necessary) 1. Use a meter at the phase monitor to ensure there is voltage across all three phases and note the voltage value. 2. The Restart Delay ➊ should be set to 200 (seconds). 3. The Voltage Adjustment (VAC) ➋ should be set to match the voltage value from Step 1. 3. The Trip Delay ➌ should be set to 7 (seconds).
PAGE 8
Refrigeration line installation 3.1 3 Refrigeration line installation: 7/8" suction / 3/8" liquid line (1810, 2110) CAUTION • The installer of the refrigeration line set must be USA Government Environmental Protection Agency (EPA) certified in proper refrigeration handling and service procedures • A qualified person must perform all roof or wall penetration • Do not form unwanted traps in refrigeration lines. A service loop is not considered an oil trap.
PAGE 9
Refrigeration line installation 3 3.2 2. Leak check field joints. 3. Evacuate line set via the condensing unit service valves. 5. Open the liquid line service valve and suction line service valve on the condensing unit. 6. Connect the self-sealing liquid and suction line quick disconnects to the evaporator. 7. Open the liquid line valve on the receiver, then the suction line valve on the compressor unit. 8.
PAGE 10
Start up and test 4 NOTICE Ice machine MUST be cleaned and sanitized prior to operation! Consult Operation and Service Manual provided with ice machine for cleaning and sanitizing instructions. 4.1 Verify operation • Turn dispenser power ON if applicable • Check current draw of compressor to verify correct electrical operation.
PAGE 11
REMOTE CONDENSING UNIT 11
PAGE 12
Harmony, Horizon, Horizon Elite, Ice Manager, and Vision are trademarks of Follett LLC. Chewblet, RIDE and Follett are registered trademarks of Follett LLC, registered in US. 12 801 Church Lane • Easton, PA 18040, USA Toll free (877) 612-5086 • +1 (610) 252-7301 www.follettice.