Horizon Elite™ Ice Machine Models with RIDE™ Technology Installation Instructions for Ice Storage Bins HCD/HMD/HCF/HMF1810RBS, HCD/HMD/HCF/HMF2110RBS HCD/HMD1810NBS, HCD/HMD2110NBS (See model number configurator on page 2 for details.) Order parts online www.follettice.com remote condensing 801 Church Lane • Easton, PA 18040, USA Toll free (877) 612-5086 • +1 (610) 252-7301 www.follettice.
Chewblet® Ice Machine Model Number Configurations HC Icemaker MC Maestro™ Chewblet® (425 Series) HC Horizon Chewblet (710, 1010, 1410, 1810, 2110 Series) HM Horizon Micro Chewblet Voltage D 1810 A V Series 425 up to C 208-230/60/1 (icemaking head) Self-contained only. 425 lbs D 115/60/1 (icemaking head) (193 kg) Self-contained and remote. If remote 710 up to unit, high side is 208-230/60/1. 675 lbs E 230/50/1 (icemaking head) (306 kg) Self-contained only.
Read and complete the following 8 installation steps 1 3 5 7 Unpack 2 Bin preparation 4 Ice transport tube 6 Internal connection BIN • RIDE Technology 8 self-contained Site preparation Louvered docking assembly External connection Front cover 3
Carefully unpack and inspect the contents of your Follett ice machine. 1.
Site preparation Prepare the installation site. 2 Provide drainage, water supply and electrical power to within 6 feet (2m) of ice machine in accordance with local and national codes. Outdoor installation of low side is not recommended and will void warranty. 2.1 2.1 Installation site requirements ➍ 7/8" ∅ (22,4mm) ➎ 3/8" ∅ (9,5mm) 2 ft.
Bin preparation Prepare the bin. 3.1 3.2 Bin top preparation 3 Bin top preparation 3" ∅ (76,2mm) CL CL • Locate center of bin top • Cut 3" (77,2mm) diameter hole in bin top 3.
Louvered docking assembly Install the louvered docking assembly. Wall bracket accessory Machine stand accessory • Mount louvered docking assembly to wall bracket accessory 2.1 4.1 4 • Mount louvered docking assembly to machine stand accessory Louvered docking assembly 2" (50,8 mm) 1.81" (46 mm) ➋ ➊ 3/8˝ ∅ high pressure line 2" (50,8 mm) Stub Typ 3.75" (95.
Transport tube Install the ice transport tube. 5.1 5 Ice transport tube installation ➍ ➏ ➐ ➋ Hot Water 160 F (71 C) ➊ ➑ ➎ ➒ ➓ 1/4" ➌ 1' Ice transport tube tips • Insulate entire length of ice transport tube ➊ • Secure ice transport tube ➋ as needed to prevent dips and traps from forming. For long tube runs see guide on page 13. • Pitch ice transport tube at least 1/4" per foot (6,4mm/.
External connections Connect utilities to louvered docking assembly. 6.1 6.2 Water and drain 6 Refrigerant ➊ ➋ ➊ ➌ Minimum 8" radius ➏ 2 ft. x 1" OD silicone tubing 3/4" barb x 3/4" FPT ➍ • Braze supplied quick-connect lines onto stub-ins ➊. 3/4" MPT x 1" slip ➎ 1" Stand pipe/Drain • Rough-in ice machine potable water supply ➊. 3/8" push-in connection will be made at shut-off valve inside machine • Remove access panel if necessary ➋.
Connect louvered docking assembly to ice machine. 7.1 7.2 Ice transport tube installation Internal connections 7 Water line ➋ ➊ ➊ • Slide ice machine into louvered docking assembly ensuring that drain tube is fully seated on barbed drain fitting ➊ • Insert ice transport tube all the way into coupling and tighten nut firmly ➋ • Insert potable water line into valve 7.3 7.4 Refrigeration lines ➊ Power cord ➊ • Evacuate line set.
7.5 7.
Front cover Install front cover to ice machine. 8.1 8.2 Install condensing unit 8 Install ice machine front cover ➋ ➊ • Slide ice machine cover over machine ensuring that tabs on back of cover slip under louvers on back of louvered docking assembly ➊ • Insert and tighten two screws through cover and into louvered docking assembly • Complete installation of condensing unit or connection to rack system. • Required rack system capacity at 0 F (-18 C) evaporator (EPR supplied by installer).
Long tube run recommendations max. 2 ft (.6m) ➋ ➊ 1/4" 1' • Pitch ice transport tube to allow melt water to drain towards ice machine ➊ • Secure insulated ice transport tube at least every 2 ft (.
self-contained BIN • RIDE Technology
BIN • RIDE Technology self-contained 15
Horizon, Horizon Elite, Maestro, Harmony, Ice Manager, SafeCLEAN, Sani-Sponge, RIDE and Vision are trademarks of Follett LLC. Chewblet is a registered trademark of Follett LLC, registered in the US. 801 Church Lane • Easton, PA 18040, USA Toll free (877) 612-5086 • +1 (610) 252-7301 www.follettice.
