Maestro Plus™ Ice Machine with RIDE™ Technology Installation Instructions for Symphony and Symphony Plus™ R425A/W (See model number configurator on page 2 for details.) Order parts online www.follettice.com self-contained 801 Church Lane • Easton, PA 18040, USA Toll free (877) 612-5086 • +1 (610) 252-7301 www.follettice.
Maestro Plus Chewblet Ice Machine Model Number Configurations MC Machine MC Chewblet (425 Series) Voltage C 220/60/1 MF Maestro Flake D 115/60/1 P Replacement E 230/50/1 R Symphony Plus RIDE Ice Machine C 425 A V S Series Condenser 425 up to A Air-cooled, self-contained 425 lbs W Water-cooled, (193 kg) self-contained Application B Ice storage bin H Harmony™ V Vision™ Configuration S RIDE® (remote ice delivery equipment) T Top-mount CAUTION! • This appliance should be permanently connecte
Contents Unpack............................................................................................................................................................................4 Unpack Ice Machine..................................................................................................................................................4 Site Preparation.............................................................................................................................................
1. Unpack Carefully unpack and inspect the contents of your Follett ice machine. 1.
2. Site Preparation Provide drainage, potable water supply and electrical power to within 6 feet (2m) of ice machine in accordance with local and national codes. Outdoor installation is not recommended and will void warranty. 2.1 Installation site requirements NEMA 5-15 ➊ ➋ ➌ ➍ ➍ 1/4" 1' Electrical ➊ WARNING! §§ This appliance should be permanently connected by a qualified person in accordance with application codes.
3. Mount Ice Machine Mounting options: Cabinet, Wall, Stand In cabinet Wall bracket Stand 18.125" (46.0 cm) 26.25" (66.7 cm) 20.125" (51.1 cm) 6.80" (17.27 cm) B A C D A - 15.125" (38.4 cm), C - 13.25" (33.6 cm) B - 18.625" (47.3 cm) D - 20.75" (52.7 cm) 3.1 Ice machine in cabinet Maestro ice machines can be installed undercounter/in-cabinet to fill bins or dispensers using RIDE technology. Care must be taken to ensure proper cabinet venting to avoid recirculation of hot air.
Completed installation with gasket and door in place air intake gasket cabinet door Side View door & gasket must mate directly A 22.75" (57.8 cm) 29" (74 cm) minimum Front supplied air intake grille cutout for supplied air intake grille 12"W x 12"H (30 cm x 30 cm) drain tube A: additional 3" (7.6 cm) required if receptacle located directly behind unit. WARNING • Keep ventilation openings in the appliance enclosure clear of obstruction. Failure to do so could result in damage to equipment.
Front View - Air Cooled 4. External Connections 4.1 Air-cooled ice machines only 4.2 Water-cooled ice machines only CONDENSER OUTLET ➋ ➌ ➍ ➋ ➊ ➊ §§ Install drain line ➊ (3/4" MPT). The rigid drain line from the ice machine must have Front Air Cooled at least 1/4" per footView (6,4 -mm/0,3 m) pitch. §§ Install ice machine potable water supply ➋ (3/8" FPT).
4.3 Bin Thermostat Cable 4.3.1 Symphony Plus DISPENSER ICE MACHINE ➋ ➊ Note: Do not apply power to ice machine bin signal connection! Ice machine can only see contact closure. §§ Connect 2-pin bin thermostat cable at electrical box on dispenser ➊ and front of ice machine ➋. 4.3.2 Symphony ICE MACHINE DISPENSER ➋ ➋ ➊ IN from dispenser RELAY ➌ ➍ Note: Do not apply power to ice machine bin signal connection! Ice machine can only see contact closure.
5. Transport tube installation Incorrect ice transport tube installation can result in wet ice and dispensing problems. Follow guidelines below to ensure correct installation. Call factory for assistance if you are unable to meet these requirements. 5.1 General requirements §§ §§ §§ §§ §§ §§ Maximum length of tube run – 20 ft (6 m). Factory approval required for longer runs. Run tube without dips. One continuous length of tube; no splices. Minimum radius of bends in tube – 6" (15.3 cm) inside radius.
6. RIDE model ice machine start up procedure The start-up procedure below is intended to ensure that ice machine is operating properly after installation has been made. Check each item listed and call factory immediately for assistance if you experience problems with unit. NOTICE! §§ Ice machine MUST be sanitized prior to operation! §§ Consult Operation and Service Manual provided with ice machine for sanitizing instructions. 6.1 Before turning on power 1. Turn on water to ice machine. 2.
Maestro Plus, Symphony Plus, and Harmony are trademarks of Follett Corporation. Follett, Chewblet and RIDE are registered trademarks of Follett Corporation, registered in the US. 801 Church Lane • Easton, PA 18040, USA Toll free (877) 612-5086 • +1 (610) 252-7301 www.follettice.