FoMaKo - Up Grade Your Meeting Experience www.fomako.net FULL HD PTZ CAMERA User Manual (V1.
Attentions This manual introduces functions, installations and operations for this PTZ camera in details. Please read this manual carefully before installation and use. 1. Cautions 1.1 Avoid damage to product caused by heavy pressure, strong vibration or immersion during transportation, storage and installation. 1.2 Housing of this product is made of organic materials. Do not expose it to any liquid, gas or solids which may corrode the shell. 1.3 Do not expose the product to rain or moisture. 1.
Content 1. CAMERA INSTALLATION..................................................................................................................................... 3 1.1. CAMERA INTRODUCTION............................................................................................................................ 3 1.2 POWER-ON INITIAL CONFIGURATION................................................................................................................... 3 1.3 VIDEO OUTPUT...........................
1. Camera Installation 1.1. Camera Introduction Figure 1.1 Product Interfaces 1. Camera Lens 2. Remote Control Receiving Indicator 3. Camera Base 4. Tripod Screw Hole 5. Screw Hole for Tripod 6. RS232 Control Interface(Input) 9. USB 2.0 Interface 10. DC12V Input Power Supply Socket 7. RS232 Control Interface(Output) 8. RS485 Input (left +, right-) 1.
1.3 Video Output USB2.0 Video Output a. USB 2.0 video cable connection: as shown in Figure1.1 label 9 b. Connect the camera and the computer via USB2.0 video cable, open the video software and select the image device to output the video. 1.4 Mounting Brackets Notes: Ceiling or wall mounting brackets can only be mounted on template and concrete wall. For safety reason, plasterboard is not recommended.
2)Ceiling Mounting 5
2. Product Overview 2.1 Product Introduction 2.1.1 Model Model No. — XXX 03---3X Optical Zoom Lens 10---10X Optical Zoom Lens Figure 2.1 Product Model 2.1.
Figure 2.2 Product Dimension 2.1.3 Accessory Please check below standard and optional accessories when unpacking the box. Standard Accessory Optional Accessory Power adapter Wall Mount IR Remote Control Ceiling Mount RS232 Cable User Manual USB2.0 Cable USB2.0 video cable: If USB2.0 video cable is required for power supply without power adapter, in which power is supplied by red end and USB video signal is transmitted by black end; if power adapter is used, USB2.
fantastic color rendition. Full HD Resolution: 1/2.9 inch high quality CMOS sensor. Resolution is up to 1920x1080 with frame rate up to 30 fps. Multiple Optical Zoom Lens: 3X/10X optical zoom lens. Leading Auto Focus Technology: Fast, accurate and stable auto focusing technology. Low Noise and High SNR: Super high SNR image is achieved with low noise CMOS. Advanced 2D/3D noise reduction technology further reduces the noise while ensuring high image clarity.
Exposure BLC Video Adjustment SNR Auto / Manual On/Off Brightness, Color, Saturation, Contrast, Sharpness, B/W mode, Gamma curve >50dB Input/output Interface Video Output USB2.0 Interface, A Type Interface Video Compression MJPG, H.264, H.
Figure2.4 Wiring Diagram 2.4.2 RS-232 Interface 1)RS-232 Interface Definition Connection to PC or Camera Controller 10 Camera 1.DTR WindowsDB-9 1.DCD 2.DSR 3.TXD 4.GND 5.RXD 6.GND 7.IR OUT 8.NC 2.RXD 3.TXD 4.DTR 5.GND 6.DSR 7.RTS 8.CTS 9.
2)RS-232 Mini-DIN 8-pin Port Definition NO. 1 2 Port DTR DSR Definition Data Terminal Ready Data Set Ready 3 4 5 6 TXD GND RXD GND 7 8 IR OUT NC Transmit Data Signal Ground Receive Data Signal Ground IR Commander Signal NO.
3. Application Instruction 3.1 Video Output 3.1.1 Power-On Initial Configuration The remote control receiving indicator flashes after power on, the pan-tilt turns left to the lowest left to the lowest, and then turns to the HOME position (both the horizontal and vertical positions are in the middle), while the movement first shrinks and then stretches. When remote control receiving indicator stops flashing, the self-checking is completed.
1) In this manual, “press the key” means a click rather than a long-press, and a special note will be given if a long-press for more than one second is required. 2) When a key-combination is required, do it in sequence. For example,“ 【*】+【#】+ 【F1】”means press“【*】”first and then press“【#】” and last press“【F1】”. 1.
ZOOM +: press【ZOOM +】key to zoom in ZOOM - : press 【ZOOM -】key to zoom out Press and hold the keys, the action of focus will keep continue and stop as soon as the key is released. 5. Set and Clear Presets Set Preset: press 【SET PRESET】 button, and then press the number key 0-9 to set preset positions. Note: 10 presets via remote control. Call Preset: Press a number key 0-9 directly to call a preset position.
【MENU】: Open / close the OSD menu 【HOME】: Camera lens back to the middle position; Confirm button; Enter next menu 【↑】 【↓】 :Choose item 【←】【→】:Modify values 【BLC ON/OFF】:Turn on or off the back light compensation 8. Camera Remote Control Address Setting 【*】+【#】+【F1】:Camera Address No.1 【*】+【#】+【F2】:Camera Address No. 2 【*】+【#】+【F3】:Camera Address No. 3 【*】+【#】+【F4】:Camera Address No. 4 3.3 Menu Introduction 3.3.
[↑↓] Select: For selecting menu [← →] Change Value: For modifying parameters [MENU] Back: Press [Menu] to return [Home] OK: Press [Home] to confirm 3.3.
Color: Enter into color setting Image: Enter into image setting Focus: Enter into focus setting Noise Reduction: Enter into noise reduction 1)Exposure Setting Move the pointer to the (EXPOSURE) in the Main Menu, click the【HOME】key and enter into the (Exposure sub menu) as shown below, EXPOSURE ================= Mode Auto EV OFF BLC OFF Flicker 50Hz G.Limit 3 DRC 2 [↑↓]Select [Menu]Back [← →]Change Value Mode: Auto, Manual, Shutter priority, Iris priority and Brightness priority.
COLOR ================ WB Mode Auto RG Tuning -10 BG Tuning -10 Saturation 100% Hue 7 AWB Sensitivity High [↑↓]Select [← →]Change Value [Menu]Back WB Mode: Auto, Manual, One Push, 3000K, 3500K, 4000K, 4500K, 5000K, 5500K, 6000K, 6500K,7000K Saturation: 60%,70%,80%,90%,100%,110%,120%,130%,140%,150%,160%,170%,180%,190%,200% Red fine-tuning: -10~10 (only available in automatic mode) Blue fine-tunable: -10~10 (only available in automatic mode) RED GAIN: 0~255(only available in Manual mode) BLUE GAIN: 0~255(only
DCI: Dynamic Contrast: Off/1~8 Minimum Illumination: On/Off 4)Focus Move the pointer to the (FOCUS) in the Menu, click the【HOME】and enter the (FOCUS) as follow, FOCUS ================= Focus Mode Auto AF-Zone All AF-Sensitivity Low [↑↓]Select [Menu]Back [← →]Change Value Focus Mode: Auto/manual AF-Zone: Up/middle/down AF-Sensitivity: High/middle/low 5)Noise Reduction Move the pointer to the (NOISE REDUCTION) in the Menu, click the 【 HOME 】 and enter the (NOISE REDUCTION) as follow, NOISE REDUCTION ====
P/T/Z ================ Speed by zoom ON Zoom speed 8 Acc Curve Slow [↑↓]Select [Menu]Back [← →]Change Value Depth of Field: Only effective for the remote controller, On/ Off; (When zooming in, the PT control speed by remoter will become slow) Zoom Speed: Set the zoom speed for the remote controller, 1~8 Image Freezing: On/Off Accelerating Curve: Fast/Slow 3.3.
RESTORE DEFAULT ================= Restore Default? NO [↑↓]Select [Menu]Back [← →]Change Value [Home]OK Restore default: YES/NO. Color style and video format cannot be restored to factory default Note: If the address of former remoter is not 1 but another one from 2, 3, 4, the corresponding camera address will restore to 1 when all parameters or system parameters are restored. User should change the remoter address to be 1 (press No.1 according to the camera so to get normal operation). 4.
4.1.
Command CAM_Shutter CAM_Iris CAM_Gain Limit CAM_Bright CAM_ExpComp CAM_Back Light CAM_WDRStrength Function Command packet Note Shutter priority 8x 01 04 39 0A FF Shutter Priority Automatic Exposure mode Iris priority 8x 01 04 39 0B FF Iris Priority Automatic Exposure mode Bright 8x 01 04 39 0D FF Bright mode Reset 8x 01 04 0A 00 FF Up 8x 01 04 0A 02 FF Down 8x 01 04 0A 03 FF Direct 8x 01 04 4A 00 00 0p 0q FF Reset 8x 01 04 0B 00 FF Up 8x 01 04 0B 02 FF Down 8x 01 04 0B 03 FF
Command Function Command packet Note 8x 01 04 49 00 00 00 0p FF P=0-E 0:60% 1:70% 2:80% 3:90% 4:100% 5:110% 6:120% 7:130% 8:140% 9:150% 10:160% 11:160% 12:180% 13:190% 14:200% 8x 01 04 22 0p 0q 0r 0s FF pqrs: Camera ID (=0000 to FFFF) ON 8x 01 04 06 06 02 FF Turn on the menu screen OFF 8x 01 04 06 06 03 FF Turn off the menu screen ON 8x 01 06 08 02 FF OFF 8x 01 06 08 03 FF On 8x 01 7D 01 03 00 00 FF IR(remote commander)receive message via Off 8x 01 7D 01 13 00 00 FF the VISCA communic
y0 50 03 FF y0 50 04 FF y0 50 0p 0q 0r 0s FF y0 50 00 FF y0 50 01 FF y0 50 02 FF y0 50 03 FF y0 50 04 FF y0 50 05 FF y0 50 00 FF y0 50 06 FF y0 50 07 FF y0 50 08 FF y0 50 09 FF y0 50 0A FF y0 50 0B FF y0 50 00 00 0p 0q FF y0 50 00 FF y0 50 03 FF y0 50 0A FF y0 50 0B FF y0 50 0D FF y0 50 00 00 0p 0q FF y0 50 00 00 0p 0q FF y0 50 0p FF y0 50 00 00 0p 0q FF Manual Focus y0 50 02 FF On Off pq: ExpComp Position On Off p: WDR Strength P: 2DNRLevel P:3D NRLevel p: Flicker Settings(0: OFF, 1: 50Hz, 2:60Hz) pq: A
CAM_GammaInq 8x 09 04 5B FF y0 50 0p FF CAM_VersionInq 8x 09 00 02 FF y0 50 ab cd mn pq rs tu vw FF VideoSystemInq 8x 09 06 23 FF y0 50 0p FF Pan-tiltMaxSpeedInq 8x 09 06 11 FF y0 50 ww zz FF Pan-tiltPosInq 8x 09 06 12 FF y0 50 0w 0w 0w 0w 0z 0z 0z 0z FF p: Gamma setting ab cd : vender ID ( 0220 ) mn pq : model ID ST ( 0510 ) 、 U2( 0512 )、U3 ( 0513 ) rs tu : ARM Version vw : reserve P: 0~E Video format 0:1080P60 8:720P30 1:1080P50 9:720P25 2:1080i60 A:1080P59.94 3:1080i50 B:1080i59.
Query Zoom Position Query Zoom Position Response 0xFF Address 0x00 0x55 0x00 0x00 0xFF Address 0x00 0x5D Value High Byte Value Low Byte SUM SUM 4.
2) Use soft cloth or tissue to clean the camera cover. 3) Wipe it with a soft, dry cloth when cleaning the camera lens. Wipe it gently with a mild detergent if needed. Do not use strong or corrosive detergents to avoid scratching the lens and affecting the video quality. 5.2 Troubleshooting 1) No video output a. Check whether the camera power supply is connected, the voltage is normal, the power indicator is lit. b. Whether the machine could do self-check after restarted. c.
6. Copyright Statement All the contents in this manual and its copyright are owned by the company. No one is allowed to imitate, copy, or translate this manual without the company’s permission. This manual contains no guarantee, standpoint expression or other implies in any form. Product specification and information in this manual is for reference only and subject to change without notice. All rights reserved. No reproducing is allowed without acknowledgement.