Instructions / Assembly

Sicilia Assembly Instructions

Part List

Oven

Cart

Screws

Apex Caps

Transformer

Wood poker

Assembly

1. Attention! Oven is very heavy! Carefully set oven on cart making sure front of oven is faced in

the same direction as the front of the cart. This can be accomplished in two ways. Option 1: The

oven can be lifted by a hoist (motor hoists can be found at most rental stores) by attaching it to a

hook that can be found behind the chimney under the insulation. Option 2: Steel rebar can be

inserted through the channel iron that can be found at the base of the front and rear of the oven. In

essence, this becomes a handle on all four corners so that the oven can be lifted manually. Do not

attempt to lift the oven from the bottom because one risks damaging fingers. (It is advisable to

remove as much weight as possible from the inside of the oven. The cast doors can be easily

removed by removing hinge pins)

2. Once oven is placed on cart and the protective film is removed from the roof (the protective film

comes off more easily when it is warm – a hair dryer will help), use screw gun to secure roof with

supplied screws making sure the larger piece with the extra flap is on top so that water cannot

enter the oven. Using a block of wood and a rubber mallet, carefully tap the roof collar down until

it rests firmly on the roof panels.

3. Install the supplied black plastic apex covers on front and back of oven

4. Install the transformer on back of oven with supplied screws and plug into oven. (Found on top

right corner on back of oven)

5. If stone is packed separately, carefully remove interior side panels from inside of oven by lifting to

disengage, slide towards front of oven and lean top of panel towards center of oven. BE VERY

CAREFULL!! It is very important to remove the panel as described. They contain stones that can

be broken if dropped outside of oven.

6. Once panels are removed with stones, place the cooking stone on floor of oven and replace side

panels making sure they are secured.

Oven Specifics

Light Switch – the interior light is powered by 12 volts arriving via the transformer and can be turned on

and off as needed

Convection Switch – the convection fan is powered by 12 volts arriving via the transformer and can be

turned on and off as needed

Removable side panels – The interior side panels can be removed for easy cleanup. To remove panels, take

out all wire racks. Next, push one panel at a time in upward motion. Once disengaged, slide forward a few

inches and lean top portion of panel towards the center of the oven exposing the stones. Remove stones.

WARNING! It is very important to follow this step. If the stones fall out of the panel they will be

damaged.

To reinsert panel, follow reverse order, making sure panel is secure on setscrews.

Moving the oven – Use extreme caution when moving the oven. To move oven, slide handles out exposing

holes in the handle. Remove cotter pins near the rubber handle and insert in the holes nearest to the oven.

PAGE 1
Sicilia Assembly Instructions Part List Oven Cart Screws Apex Caps Transformer Wood poker Assembly 1. 2. 3. 4. 5. 6. Attention! Oven is very heavy! Carefully set oven on cart making sure front of oven is faced in the same direction as the front of the cart. This can be accomplished in two ways. Option 1: The oven can be lifted by a hoist (motor hoists can be found at most rental stores) by attaching it to a hook that can be found behind the chimney under the insulation.
PAGE 2
This will prevent the handle from sliding in during movement which could cause lose of control. WARNING: DO NOT ATTEMPT TO MOVE WHILE OVEN IS HOT! Damper control – The fire can be controlled by adjusting the sliding damper on the door and by adjusting the damper valve on the chimneystack. The damper valve on the stack is open when the handle is vertical and closed when it is horizontal. Once the desired oven temperature is achieved, the burn is most efficient when the dampers are at least partially closed.