Contents Before driving Introduction 2 Instrumentation 5 Controls and features 18 Seating and safety restraints 53 Starting and driving Starting 83 Driving 91 Roadside emergencies 135 Servicing Maintenance and care 154 Capacities and specifications 213 Reporting safety defects 220 Index 221 1
Introduction com_icons.01 ICONS Indicates a warning. Read the following section on Warnings for a full explanation of them. Indicates that vehicle information related to recycling and other environmental concerns will follow. We must all play our part in protecting the environment. Correct vehicle usage and the authorized disposal of waste cleaning and lubrication materials are significant steps towards this aim.
Introduction increase the performance of your vehicle up to the permitted maximum speeds. com_info_guide.01 INFORMATION ABOUT THIS GUIDE The information found in this guide was in effect at the time of printing. Ford may change the contents without notice and without incurring obligation. f12_utility_notice Notice to owners of utility type vehicles Before you drive your vehicle, please read this Owner’s Guide carefully. Your vehicle is not a passenger car.
Introduction Your vehicle is not equipped with the Ford Ambulance Preparation package.
Instrumentation Engine oil pressure gauge (pg. 16) Charging system gauge (pg. 16) Speed control* (pg. 33) Fuel gauge (pg. 15) Engine coolant temperature gauge (pg. 15) Speedometer (pg. 14) F H E L Transmission control switch (pg. 38) 40 60 30 20 40 20 Tachometer* (pg. 15) DRIVE 50 60 80 100 000005 km/h H OFF OVER 70 120 80 140 90 2 1 3 4 5 18 6 C 8 INT 2 INT 1 OFF RES ON P PANEL AUTO DIM LAMP SET ACCEL OFF COAST SRS Headlamp control (pg.
Instrumentation f12_inst_warn_lights Electronic sound system (pg. 22) Vents (pg. 25) VOL – PUSH ON FM 1 AM FM BASS TREB SEEK TUNE DISCS SCAN FF 2 REW 1 CLK ST BAL FADE TAPE CD EJ DOLBY SYSTEM SIDE 1-2 3 COMP 5 4 LO SHUFFLE 6 OFF 4H 2H AUTO SET PANEL 4L *A/C HI *MAX A/C COOL WARM PANEL & FLOOR FLOOR FLR & DEF DEF PASSENGER AIRBAG OFF ON OFF Auxiliary power point (pg. 22) * if equipped 4WD Control* (pg. 110) Climate controls (pg. 25) Passenger air bag deactivate switch (pg.
Instrumentation INSTRUMENT CLUSTER WARNING LIGHTS AND CHIMES Your vehicle is equipped with one of the following instrument clusters: LOW FUEL H C DOOR AJAR 40 60 30 20 F BRAKE 10 0 ! 100 H 70 120 000005 40 20 50 60 80 L 80 140 km/h 18 90 180 MPH 100 0 0 1 0 8 E CHECK ENGINE LOW FUEL F H E L DOOR AJAR 40 60 30 20 20 BRAKE H ! 18 FUEL RESET ABS 40 50 60 80 100 000005 C 8 70 120 80 140 km/h 10 0 LOW RANGE 4x4 0 0 1 0 90 100 3 2 THEFT 4 1 5 0 RPMx1000 CHECK E
Instrumentation Engine coolant temperature Illuminates briefly when the ignition key is turned to On (light from optional cluster shown). Illuminates when the engine coolant temperature is high. Stop the engine and check the engine coolant temperature level as soon as possible. Refer to Checking and adding engine coolant and What you should know about fail-safe cooling in the Maintenance and care section.
Instrumentation Brake system warning Extinguishes when the parking brake is released. Illumination after releasing the parking brake indicates low brake fluid level. BRAKE ! com_safety_belt.01 Safety belt Illuminates when the ignition is switched on to remind you to fasten your safety belts. For more information, refer to Using the safety restraints properly in the Seating and safety restraints chapter. f12_air_bag_readiness Air bag readiness Briefly illuminates when the ignition is turned to On.
Instrumentation Transmission control indicator light (TCIL) The TCIL (OFF), located on the end of the gearshift lever, may flash steadily if a malfunction has been detected. If the TCIL is flashing, contact your Ford dealer as soon as possible. If this condition persists, damage to the transmission could occur. For more information, refer to the Driving chapter. 4x4 light (if equipped) Illuminates when 4H (Four-Wheel Drive) or 4L (Four-Wheel Drive Low) is engaged.
Instrumentation Anti-theft system (if equipped) Illuminates when the anti-theft system is arming and flashes when the anti-theft system is armed. THEFT com_high_beams.01 High beams Illuminates when the headlamp high beams are on. com_turn_signal.01 Turn signal Illuminates when the left or right turn signal or the hazard lights are turned on.
Instrumentation warning and indicator lights shown above will illiminate for a brief time. If any of these lights do not illuminate, contact your dealer for service. f12_headlamps_on Headlamps on warning chime Sounds when the headlamps are on, the key is out of the ignition and any door is opened. f12_key_in_ignition Key-in-ignition warning chime Sounds when the key is left in the ignition and any door is opened. The chime is not active when the ignition key is in the On position. com_safety_chime.
Instrumentation INSTRUMENT CLUSTER GAUGES Your vehicle has one of the following instrument clusters: 50 60 80 40 60 30 H C 20 20 120 L 80 140 km/h 10 0 F H 70 100 000005 40 90 18 180 100 0 0 1 0 E 8 f12_speedometer F H E L 40 60 30 20 20 H 18 40 50 60 80 100 000005 80 140 km/h 10 0 MPH 70 120 4 THEFT 90 180 0 0 1 0 3 2 100 C 1 5 0 RPMx1000 6 8 Speedometer 40 60 50 60 80 100 30 000005 40 20 20 10 0 Indicates the current vehicle road speed.
f12_engine_coolant Instrumentation Tachometer (if equipped) Indicates the engine speed in revolutions per minute. 3 2 Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the normal area. If it enters the red section, the engine is overheating. Switch off the ignition and let it cool. Refer to Checking and adding engine coolant or What you should know about fail safe cooling in the Maintenance and care chapter.
Instrumentation Voltage gauge If the pointer moves and stays outside of the normal range, it indicates that the battery is not being charged. Have the vehicle’s electrical system checked by your dealer as soon as possible. f12_oil_pressure 18 8 Engine oil pressure gauge This shows the engine oil pressure in the system. Sufficient pressure exists as long as the needle remains in the normal range.
Instrumentation Trip odometer Registers the kilometers (miles) of individual journeys. To reset, depress the control.
Controls and features f12_foglamp_switch f12_headlamp_switch Headlamp/foglamp control This control operates the headlamps and foglamps. — Off — Parking lamps on. — Headlamps on.
Controls and features Foglamp control The headlamp control also operates the foglamps. The foglamps can be turned on only when the headlamps are in the position. Pull headlamp control towards you to turn foglamps on. The foglamp indicator light (located to the right of the control) will illuminate.
f12_autolamp Controls and features Panel dimmer control Turn control up to brighten panel. Turn control down to dim panel. P Autolamp delay system (if equipped) The autolamp delay system sets the headlamp to turn on and off automatically. You can set the autolamp to: • turn on the exterior lamps automatically at night. • turn off the lamps automatically during daylight.
Controls and features three minutes after you turn the key to OFF. 1. Turn control up to increase delay. The indicator light under the autolamp control illuminates when the autolamps are activated. 2. Turn control down to decrease delay. To turn autolamp system off, turn control down all the way until a click is felt. f12_4wd_switch f12_power_point PANEL AUTO DIM LAMP Electronic shift 4WD system (if equipped) This controls the Electronic Shift 4WD operation.
Controls and features Auxiliary power point This 12V power point is an additional power source for electrical accessories. Do not plug optional electrical accessories into the cigarette lighter. Use the power point. f12_pass_srs_deact Passenger air bag deactivate switch This switch must be used to deactivate the passenger air bag whenever a child seat is used in the right front or center front passenger seat position.
f12_air_suspension Controls and features Fuel pump shut-off switch Refer to the Roadside emergencies chapter for information on operating the fuel pump shut-off switch.
f12_climate_controls Controls and features Air suspension load leveling (if equipped) Your vehicle is equipped with an air suspension system for the rear suspension that levels your vehicle when carrying heavy loads. Refer to Air suspension load leveling in the Driving chapter for more information.
f12_temperature Controls and features f12_climate_controls CLIMATE CONTROLS f12_ip_vents Operating climate controls Instrument panel vents There are four vents on the instrument panel. These vents are equipped with controls to adjust the amount and direction of air passing through them. f12_fan_speed Temperature Turn temperature control to the desired temperature.
f12_mode_control Controls and features Fan speed Turn the fan speed control to the desired speed. LO HI f12_airflow Airflow and air conditioning (if equipped) Turn the mode control to the desired airflow position.
Controls and features The PANEL position allows outside air to flow through the instrument panel vents. Select PANEL & FLOOR for air to flow through these vents: VOL – PUSH ON FM 1 AM FM BASS TREB SEEK SCAN TUNE DISCS P FF 2 REW 1 CLK ST BAL FADE AUTO SET TAPE CD EJ DOLBY SYSTEM SIDE 1-2 3 COMP 5 4 SHUFFLE 6 OFF LO *A/C *MAX A/C HI The PANEL & FLOOR position directs outside air to flow between the panel and floor vents.
Controls and features The FLOOR position directs outside air to flow through the floor vents. Select FLR & DEF for air to flow through these vents: VOL – PUSH ON FM 1 AM FM BASS TREB SEEK TUNE DISCS P SCAN FF 2 REW 1 CLK ST BAL FADE AUTO SET TAPE CD EJ DOLBY SYSTEM SIDE 1-2 3 COMP 5 4 SHUFFLE 6 OFF LO *A/C *MAX A/C HI The FLR & DEF position directs outside air to flow through the floor vents and the windshield defroster vents.
Controls and features Air conditioning Select A/C for air conditioned air to flow through these vents: VOL – PUSH ON FM 1 AM FM BASS TREB SEEK TUNE DISCS SCAN FF 2 REW 1 P CLK ST BAL FADE AUTO SET TAPE CD EJ DOLBY SYSTEM SIDE 1-2 3 COMP 5 4 SHUFFLE 6 OFF LO *A/C * HI MAX A/C ❄ The A/C mode directs outside air conditioned air to flow through the instrument panel vents. The A/C mode can be used for heating, ventilating and defogging the windows or air conditioning.
Controls and features OFF position Select the OFF position for all climate control functions to cease. The outside inlet door will close and the fan is shut off. Maximum heating Set mode control to FLOOR, turn temperature control to maximum heat (red) and set fan speed control to HI.
Controls and features Defrosting windshield Set mode control to or FLR & DEF, turn temperature control to maximum heat (red) and set fan speed control to HI. LO OFF PANEL A/C HI MAX A/C COOL WARM PANEL & FLOOR FLOOR FLR & DEF DEF Drive with the climate control system on (in either the heating or air conditioning mode) to reduce humidity in your vehicle. To prevent air intake restriction, remove any snow, ice or leaves from the air intake area located directly under the windshield.
f12_ignition_positions Controls and features Positions of the ignition 4 3 5 2 1 1 (Accessory) - allows electrical accessories such as the audio system and wiper/washer to operate when the engine is not running. 2 (Lock) - locks the steering wheel and automatic gearshift lever (if equipped).
Controls and features 3 (Off) - shuts off the engine and all accessories without locking the steering wheel. 4 (On) - tests the warning lights. Key remains here when engine is running. 5 (Start) - cranks the engine. Key returns to 4(On) when released. com_speed_off.01 f12_speed_cont com_speed_on.01 Speed control (if equipped) To turn speed control on • Press ON ON OFF To turn speed control off • Press OFF or • Turn off the vehicle ignition.
Controls and features If you drive up or down a steep hill, your vehicle speed may vary momentarily slower or faster than the set speed. This is normal. Speed control cannot reduce the vehicle speed if it increases above the set speed on a downhill. If your vehicle speed is faster than the set speed while driving on a downhill in Overdrive, you may want to shift to the next lower gear to reduce your vehicle speed.
Controls and features com_slow_down.01 previously programmed set speed. To set a lower set speed • Press and hold COAST. Release the switch when the desired vehicle speed is reached, or • Press and release COAST. Each press will decrease the set speed by 1.6 km/h (1 mph) or • Depress the brake pedal. When the desired vehicle speed is reached press SET ACCEL. RES SET ACCEL COAST com_disengage_speed_control.01 com_resume_feature.01 To return to a set speed • Press RES.
Controls and features Wiper/washer controls • Push and hold the end to activate the washer. • Push end briefly for a single wipe. • Push and hold for a constant cycle. • Turn the control to adjust intermittent wiper speed.
Controls and features High beam control • Push the stalk forward to activate the high beam lamps. • Pull the stalk towards you to activate the “flash to pass” function. Turn signals Push the stalk down to activate the left turn signal; push the stalk up to activate the right turn signal.
f12_deactivate_od Controls and features f12_activate_od Overdrive control Activating overdrive D (Overdrive) is the normal drive position for the best fuel economy. The overdrive function allows automatic upshifts to second, third and fourth gear. OVERDRIVE OFF Deactivating overdrive Press the transmission control switch on the end of the gearshift lever. The transmission control indicator light (TCIL) (OFF) will illuminate on the end of the gearshift lever.
Controls and features Deactivate overdrive whenever driving conditions (i.e., city traffic, hilly terrain, etc.) cause the transmission to shift excessively between D (Overdrive) and D(Drive) ranges. Also deactivate D (Overdrive) when: • driving with a heavy load • towing a trailer up or down steep hills • additional engine braking is desired. Transmission control indicator light (TCIL) The TCIL (OFF), located on the end of the gearshift lever, may flash steadily if a malfunction has been detected.
Controls and features f12_overhead_overall Tilt steering (if equipped) Pull the lever to adjust the steering column angle. Push the lever back up to lock the steering wheel into position. Never adjust the steering wheel when the vehicle is moving. f12_illuminated_entry f12_domemap_lamp OVERHEAD CONTROLS Dome/map lamp (if equipped) Press either the left or right switch to activate the left or right map lamps.
Controls and features Illuminated entry The interior lamps illuminate when: • either front door handle is lifted or • the remote entry system is used to unlock the door or sound the personal alarm. See Remote entry system for more information. The system automatically turns off after 25 seconds or when the ignition is turned to the Start or Accessory positions. The inside lights will not turn off if: • they have been turned on with the dimmer control or • any door is open.
Controls and features f12_driver_control Power windows (if equipped) Driver-side window control • Press rear of switch to open window. • Press front of switch to close window. The driver-side power window has a one-touch down feature. When AUTO is fully pressed (two clicks will be heard), the driver-side window will move completely down. This feature can be cancelled by pressing the driver-side power window switch again.
f12_acc_delay Controls and features Passenger-side window controls • Press rear of switches to open passenger window. • Press front of switches to close passenger window. L R AUTO U L L U Accessory delay (if equipped) With accessory delay, the window switches may be used for up to ten minutes after the ignition switch is turned to the Off position or until either door is opened.
f12_remote_mirrors Controls and features f12_driver_control Power locks (if equipped) Driver and passenger controls • Press L to lock both doors. • Press U to unlock both doors. L R AUTO L Dual electric remote control mirrors (if equipped) 1. Select driver or passenger mirror by moving selector lever left (L) for driver or right (R) for passenger. 2. Move the mirror control until mirror reaches desired position. 3. Move selector lever to center to “lock” position.
f12_third_door Controls and features Fold-away mirrors Pull the side mirrors in carefully when driving through a narrow space, like an automatic car wash. Third door (if equipped) On SuperCab models a third door is located behind the passenger door. This door allows for improved access to the rear passenger compartment.
Controls and features door jamb or the handle on the interior of the third door. • To lock the third door, lock the passenger door or press the power lock switch (if equipped). • When the passenger door is unlocked, the third door cannot be opened until the passenger door is opened. The third door can then be opened.
Controls and features f12_tailgate_lock Tailgate lock (if equipped) Your vehicle is equipped with a tailgate lock designed to prevent theft of the tailgate. • Insert ignition key and turn to the right to engage lock. • Turn ignition key to the left to unlock. f12_tailgate_removal Tailgate removal Your tailgate is removable to allow more room for loading. 1. Lower the tailgate. 2. Use a screwdriver to pry the spring clip (on each connector) past the head of the support screw. Disconnect cable. 3.
Controls and features LO CK U LO N CK PA NIC f12_remote_entry Remote entry system (if equipped) The remote entry system allows you to lock or unlock all vehicle doors without a key. The remote entry features only operate with the ignition key in the Off position. It also arms and disarms the anti-theft system (for more information on the anti-theft system, refer to Anti-theft system in this chapter.) Unlocking the doors Press UNLOCK to unlock the driver door. The interior lamps will illuminate.
Controls and features Locking the doors Press LOCK to lock all doors. To confirm that all doors are closed and locked, press the LOCK control a second time. The doors will lock again, the horn will chirp and the lamps will flash. LO CK U LO N CK PA NIC This process will also arm your anti-theft system. If the horn chirps twice, a door is still ajar and the anti-theft system will not arm. For more information on arming the anti-theft system, refer to Anti-theft system in this chapter.
Controls and features The remote entry system may not arm and disarm non-factory installed anti-theft systems. f12_replacing_batteries Replacing the batteries The transmitter is powered by two coin type three-volt lithium batteries. A decrease in operating range can be caused by: • battery failure • weather conditions • structures around the vehicle. Replacement batteries for the remote entry transmitters may be purchased at pharmacies, watch stores or at authorized dealers. To replace the batteries: 1.
Controls and features subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. f12_arming_anti_theft Anti-theft system (if equipped) When armed, the anti-theft system prevents unauthorized entry into your vehicle.
Controls and features • sound the horn • prohibit the vehicle from starting. The flashing headlamps and the honking horn automatically shut off after about three minutes and will remain off unless another unauthorized entry is attempted. However, the vehicle will not start until the system is disarmed. Disarming an untriggered anti-theft system Press the UNLOCK control or unlock either door with the key to disarm the untriggered system.
Seating and safety restraints f12_adjusting_bench SEATING f12_split_bench Full bench seat (if equipped) • Lift the release bar to move the seat forward or backward. Ensure that the seat is relatched into place. • Push down the release lever to quickly fold the seatback forward. 60/40 split bench seat (if equipped) • Lift the release bar to move the seat forward or backward. Ensure the seat is relatched into place.
Seating and safety restraints • Pull the seatback handle up to recline the seat. f12_adjust_man_bucket • Turn the lumbar support dial to adjust firmness. • Push down the release lever to quickly fold the seatback forward. Center armrest (if equipped) Pull the strap down to move the armrest down.
Seating and safety restraints Captain’s chair (if equipped) • Lift the release bar to move the seat forward or rearward. Ensure that the seat is relatched into place. • Pull the seatback handle up to recline the seat. • Push the release lever down to quickly fold the seatback forward. f12_adjust_power_seat Power seats (if equipped) • Pull up the seatback handle to recline the seat. • Push down the release lever to quickly fold the seatback forward.
Seating and safety restraints Press switch to tilt the front of the seat up or down. Press switch to tilt the rear of the seat up or down.
f12_adjust_lumbar Seating and safety restraints Press control to move the seat forward, backward, up or down. f12_rear_bench Adjustable lumbar support Turn the lumbar support dial clockwise to adjust firmness.
Seating and safety restraints 60/40 split rear seat (if equipped) When folded down, the rear seats provide a “load floor” of additional storage space. To fold down the rear seats: 1. Pull the straps to lower the seat cushions. 2. Store the center safety belt in the opening on the seat back. When returning the seats to their normal position: 1. Clear the load floor before folding seat up. 2. Ensure the seat cushion is latched into place. 3. Remove center safety belt from its stowed position.
Seating and safety restraints All occupants of the vehicle, including the driver, should always wear their safety belts. To prevent the risk of injury, make sure children sit where they can be properly restrained. It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts.
Seating and safety restraints f12_comb_lap_sh_belts Vehicle sensitive (emergency) locking mode The vehicle sensitive mode is the normal retractor mode, allowing free shoulder belt length adjustment to your movements and locking in response to vehicle movement.
Seating and safety restraints f12_auto_lock_mode movement of the driver and passengers. The front seat belt system can also be made to lock manually by quickly pulling on the shoulder belt. Rear seat belts (if equipped) cannot be made to lock up by pulling quickly on the belt. Automatic locking mode In this mode, the shoulder belt is automatically pre-locked. The belt will still retract to remove any slack in the shoulder belt. The automatic locking mode is not available on the driver safety belt.
Seating and safety restraints Using the automatic locking mode The automatic locking mode must be used when installing a child safety seat in any outboard passenger seat. 1. Buckle the combination lap and shoulder belt. 2. Grasp the shoulder belt portion and pull downward until the entire belt is extracted. 3. Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates that the safety belt is now in the automatic locking mode.
Seating and safety restraints Front seat safety belt height adjustment Your vehicle has safety belt height adjustments for the driver and passenger seating positions. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder. 1. Push the button and slide down to lower the shoulder belt height. 2. Push the button and slide up to raise the shoulder belt height. 3. Pull down on the height adjustment assembly to make sure it is locked in place.
Seating and safety restraints The lap belt must be adjusted before use. To shorten the belt: • Buckle the belt. • Pull the loose end of the belt until snug. f12_sbelt_warning_chime To lengthen the belt: • Tip and pull the tongue. Do not wear the lap belt around your waist. Shorten and fasten the belt when not in use. Safety belt warning light and indicator chime illuminates in the instrument cluster and a chime sounds to remind the occupants to fasten their safety belts.
Seating and safety restraints Conditions of operation If... The driver safety belt is not buckled when the ignition key is turned to On... Then... The safety belt indicator illuminates for 1-2 minutes and the reminder chime sounds for 4-8 seconds. The safety belt indicator light and the reminder chime turn off. The driver safety belt is buckled while the indicator light is illuminated and the reminder chime is sounding...
Seating and safety restraints with a safety belt extension assembly (part # 611C22). Safety belt extensions are available at no cost from your Ford or Lincoln/Mercury dealer. Use only extensions manufactured by the same supplier as the safety belt. Manufacturer identification is located at the end of the webbing on the label. Also, use the safety belt extension only if the safety belt is too short for you when fully extended. Do not use extension to change the fit of the shoulder belt across the torso.
Seating and safety restraints The right front passenger air bag is not designed to restrain occupants in the front seating position. Do not place objects or mount equipment on or near the air bag covers that may come into contact with an inflating air bag. Do not attempt to service, repair, or modify the Air Bag Supplemental Restraint System or its fuses. See your Ford or Lincoln-Mercury dealer. com_children.
Seating and safety restraints com_how_work.01 Children should always wear their safety belts. Failure to follow these instructions may increase the risk of injury in a collision. Rear-facing child seats or infant carriers should never be placed in the front seats. How does the air bag supplemental restraint system work? The SRS is designed to activate when the vehicle sustains sufficient longitudinal deceleration, similar to hitting a fixed barrier head on at 12–24 km/h (8–14 mph).
Seating and safety restraints were not of the type sufficient to cause activation. The air bags inflate and deflate rapidly upon activation. After air bag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the air bag.
Seating and safety restraints If the air bag is inflated, the air bag will not function again and must be replaced immediately. If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision. The SRS consists of: • driver and passenger air bag modules (which include the inflators and air bags), • one or more impact and safing sensors, • a readiness light and tone • and the electrical wiring which connects the components.
Seating and safety restraints A difficulty with the system is indicated by one or more of the following: • The readiness light will either flash or stay lit. • The readiness light will not illuminate immediately after ignition is turned on. • A group of five beeps will be heard. The tone pattern will repeat periodically until the problem and light are repaired. If any of these things happen, even intermittently, have the SRS serviced at your dealership or by a qualified technician immediately.
Seating and safety restraints Keep the passenger air bag turned on unless there is a rear-facing infant seat installed in the front seat. When the passenger air bag switch is turned off, the passenger air bag will not inflate in a collision. If the passenger air bag switch is turned off, it increases the likelihood of injury to forward facing occupants in the passenger seat. Turning the passenger air bag off 1. Insert the ignition key, turn the switch to OFF and remove the key. 2.
Seating and safety restraints In order to avoid inadvertent deployment of the passenger air bag, always remove the ignition key from the passenger air bag deactivate switch. Turning the passenger air bag back on The passenger air bag remains off until you turn it back on. 1. Insert the ignition key and turn the switch to ON. 2. The OFF light will not illuminate when the ignition is turned to On.
Seating and safety restraints Keep the passenger air bag turned on unless there is a rear-facing infant seat installed in the front seat. When the passenger air bag switch is turned off, the passenger air bag will not inflate in a collision. Disposal of air bags and air bag equipped vehicles For disposal of air bags or air bag equipped vehicles, see your local dealership or qualified technician. Air bags MUST BE disposed of by qualified personnel.
Seating and safety restraints Always follow the instructions and warnings that come with any infant or child restraint you might use. If possible, place children in the rear seat of your vehicle. Accident statistics suggest that children are safer when properly restrained in rear seating positions than when they are restrained in front seating positions. com_safety_belts.
Seating and safety restraints Do not leave children, unreliable adults, or pets unattended in your vehicle. To improve the fit of lap and shoulder belts on children who have outgrown child safety seats, Ford recommends use of a belt-positioning booster seat that is labelled as conforming to all Federal motor vehicle safety standards.
Seating and safety restraints Child and infant or child safety seats Carefully follow all of the manufacturer’s instructions included with the safety seat you put in your vehicle. If you do not install and use the safety seat properly, the child may be injured in a sudden stop or collision. Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage.
Seating and safety restraints Installing child safety seats in combination lap and shoulder belt seating positions 1. Position the child safety seat in a seat with a combination lap and shoulder belt. If you choose to install a child safety seat in the front passenger seat, move the seat as far back as possible.
Seating and safety restraints Keep the passenger air bag turned on unless there is a rear-facing infant seat installed in the front seat. When the passenger air bag switch is turned off, the passenger air bag will not inflate in a collision. 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together. 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions.
Seating and safety restraints sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle for that seating position until you hear and feel the latch engage. Make sure the tongue is latched securely by pulling on it. S ES PR 5.
Seating and safety restraints pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode. 7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down on the child seat. 8. Allow the safety belt to retract to remove any slack in the belt. 9.
Seating and safety restraints able to pull more belt out). If the retractor is not locked, unbuckle the belt and repeat steps two through nine. Check to make sure the child seat is properly secured before each use. Using a tether strap Ford recommends using child safety seats with a top tether strap. Contact the manufacturer of your safety seat for information about ordering a tether strap if one is not provided to you. Contact your Ford dealer for a free tether strap if one is not provided to you.
Starting com_important_precautions.05 STARTING YOUR VEHICLE Important safety precautions A computer system controls the engine’s idle revolutions per minute (RPM). When the engine starts, the idle RPM runs faster to warm the engine. If the engine idle speed does not slow down automatically, have the vehicle checked. Do not allow the vehicle to idle for more than ten minutes.
Starting If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately. Do not drive if you smell exhaust fumes. Preparing to start the vehicle Engine starting is controlled by the spark ignition system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting.
Starting the Seating and safety restraints chapter. 2. Make sure the headlamps and vehicle accessories are off. P If starting a vehicle with an automatic transmission: • Make sure the parking brake is set. • Make sure the gearshift is in P (Park).
Starting If starting a vehicle with a manual transmission: • Make sure the parking brake is set. • Push the clutch pedal to the floor.
Starting 3. Turn the key to the ON position (without turning the key to START). Make sure the following lights illuminate briefly. If a light fails to illuminate, have the vehicle serviced.
Starting com_starting_vehicle.01 STARTING PROCEDURE Starting the engine 1. Turn the key to 5 (Start) without pressing the accelerator. The key will return to 4 (On). 4 3 5 2 1 2. If the engine does not start within five seconds, wait ten seconds and try again. 3. If the engine does not start in two attempts OR the temperature is below —12°C (10°F), depress accelerator and start the engine while holding the accelerator down. Release accelerator when engine starts. 4.
Starting the vehicle. Using the heater for longer than three hours will not harm the engine, so the heater can be plugged in the night before starting the vehicle. To prevent electrical shock, do not use your heater with ungrounded electrical systems or two-pronged (cheater) adapters. com_guarding_exhaust.01 Guarding against exhaust fumes Although odorless and colorless, carbon monoxide is present in exhaust fumes. Take precautions to avoid its dangerous effects.
Starting Important ventilating information If the engine is idling while the vehicle is stopped in an open area for long periods of time, open the windows at least 2.5 cm (one inch). L R AUTO L U OFF PANEL A/C MAX A/C Adjust the heating or air conditioning (if equipped) to bring in fresh air. Improve vehicle ventilation by keeping all air inlet vents clear of snow, leaves and other debris.
Driving f12_rear_abs BRAKES Rear anti-lock brake system (ABS) (if equipped) This system prevents one or both rear wheels from locking up when the brakes are applied during a sudden stop. Even with rear ABS, the front brakes may lock up on any surface. Be careful when braking, especially on loose snow or gravel. com_abs.01 Anti-lock brake system (ABS) (if equipped) The ABS operates by detecting the onset of wheel lock up during brake applications and compensating for this tendency.
Driving braking technique. However, avoid taking any unnecessary risks. Parking brake The parking brake should be used whenever you park your vehicle. It is not designed to stop a moving vehicle. However, if the normal brakes fail, the parking brake can be used to stop your vehicle in an emergency. Since the parking brake applies only the rear brakes, the vehicle’s stopping distance will increase greatly and the handling of your vehicle will be adversely affected.
Driving switch is turned to On) until the parking brake is released. • Automatic and manual transmissions – Fully depress the parking brake pedal. When you leave your vehicle, place the gearshift lever in P (Park). Set the parking brake fully, and shut off the engine. Never park your vehicle in N (Neutral). If you do not take these precautions, your vehicle may move suddenly and injure someone.
Driving Do not leave the vehicle unattended with the transfer case in the N (Neutral) position. Always set the parking brake fully and turn off the ignition when leaving the vehicle. f12_releasing_pbrake Releasing parking brake Pull the BRAKE lever forward. BRAKE If the parking brake is fully released, but the Brake System light remains on, have the brakes checked immediately. They may not be working properly.
Driving particularly when one or more wheels are on a surface with poor traction. f12_air_suspension AIR SUSPENSION (IF EQUIPPED) The air suspension system for the rear wheels is designed to keep your vehicle at a constant level by adding or releasing air from the rear springs to compensate for increases or decreases in vehicle load. Normal vehicle operation does not require any action by the driver.
Driving f12_automatic TRANSMISSION OPERATION Automatic transmission operation (if equipped) Hold the brake pedal down while you move the gearshift lever from position to position. If you do not hold the brake pedal down, your vehicle may move unexpectedly and injure someone. Pull the gearshift lever towards you and downward to move the automatic gearshift. P (Park) – Always come to a complete stop before shifting into or out of P (Park). When you leave your vehicle, place the gearshift lever in P (Park).
Driving N (Neutral) – Vehicle is free to roll. D (Overdrive) – The normal driving position for the best fuel economy. Transmission operates in gears one through four. D (Overdrive) can be deactivated by pressing the transmission control switch on the end of the gearshift lever. The transmission control indicator light (TCIL) (OFF) on the end of the gearshift lever will remain off. D (Drive) – Not shown on the display. Activate by pressing the transmission control switch on the end of the gearshift lever.
Driving Each time the vehicle is started, the transmission will automatically return to normal overdrive mode. 2 (Second) – Use 2 (Second) to start-up on slippery roads or to provide additional engine braking on downgrades. Transmission operates in first and second gears. 1 (Low) – Use 1 (Low) to provide maximum engine braking on steep downgrades. Upshifts can be made by shifting to 2 (Second) or to D (Overdrive).
Driving 2. Apply the parking brake. 4 3 5 2 1 3. Turn ignition key to Lock and remove the key. 4. Re-insert the ignition key and turn it to Off. 5. Shift the transmission to N (Neutral). 6. Start the vehicle. If you need to use the above procedure, it is possible that a fuse has blown and your brakelamps may not be functioning. Refer to the Roadside emergencies chapter for instructions on replacing fuses. Do not drive your vehicle until you verify that the brakelamps are working.
Driving When starting a vehicle with a manual transmission, you must: 1. Put gearshift in N (Neutral). 2. Hold down brake pedal.
Driving 3. Depress clutch pedal. 4 3 5 2 1 4. Turn ignition key to Start to start the engine and let it idle for a few seconds. 5. Release the brake pedal. 6. Release clutch slowly while pressing down slowly on the accelerator pedal. • Do not drive with your foot resting on the clutch pedal and do not use the clutch to hold your vehicle at a standstill while waiting on a hill. These actions will seriously reduce clutch life.
Driving Upshifts when accelerating (recommended for best fuel economy) Shift from: Transfer case position1 (if equipped) 2H or 4H 4L 1-2 14 km/h (9 mph) 5 km/h (3 mph) 2-3 32 km/h (20 mph) 11 km/h (7 mph) 3-4 50 km/h (31 mph) 19 km/h (12 mph) 71 km/h (44 mph) 27 km/h (17 mph) 4 - D (Overdrive) Upshifts when cruising (recommended for best fuel economy) Shift from: Transfer case position1 (if equipped) 2H or 4H 4L 1-2 16 km/h (10 mph) 6 km/h (4 mph) 2-3 26 km/h (16 mph) 10 km/h (6 mph) 3-4 43 km/h (27 mph) 16
Driving f12_parking Parking your vehicle 1. Apply brake and shift into N (Neutral). 1 3 D 2 4 R 1 3 D 2 4 R 2. Set parking brake. 3. Shift into 1 (First).
Driving 4. Turn ignition to Off. 4 3 5 2 1 Do not park your vehicle in Neutral, it may move unexpectedly and injure someone. Use 1 (First) gear and set the parking brake fully. Reverse Make sure that your vehicle is at a complete stop before you shift into R (Reverse). Failure to do so may damage the transmission. Put the gearshift in N (Neutral) and wait at least three seconds before shifting into R (Reverse).
f12_four_wd Driving Removing key from ignition Turn the ignition key to Lock. Push the release lever forward while removing the key from the ignition. FOUR-WHEEL DRIVE OPERATION (4WD) (IF EQUIPPED) When Four–wheel drive (4WD) is engaged, power is supplied to all four wheels through a transfer case. 4WD power can be selected when additional driving power is desired.
Driving Utility and four-wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road conditions. Avoid sharp turns or abrupt maneuvers in these vehicles. 4WD operation is not recommended on dry pavement. Doing so could result in difficult disengagement of the transfer case, increased tire wear and decreased fuel economy.
Driving Using lever-operated 4WD system (if equipped) 2H (2WD High) – Power to rear axle only. 4H (4WD High) – Power to front and rear axles. N (Neutral) – No power to either axle. 4L (4WD Low)– Power to front and rear axles at reduced speed. f12_shifting_2h_4h 2H 4H N 4L Shifting from 2H (2WD High) to 4H (4WD High) Move the transfer case lever to 4H (4WD High) at a stop or any forward speed up to 88 km/h (55 mph).
Driving f12_shifting_4h_4l Shifting from 4H (4WD High) to 2H (2WD High) Move the transfer case lever to 2H (2WD High) at a stop or any forward speed up to 88 km/h (55 mph). 2H 4H N 4L Shifting from 4H (4WD High) to 4L (4WD Low) 1. Depress the brake. 2. Place the gearshift lever in N (Neutral) (automatic transmission) or depress the clutch (manual transmission). 3. Pull the transfer case shift lever through N (Neutral) directly to 4H (4WD High) or 4L (4WD Low).
Driving 3. Place the gearshift in N (Neutral) (automatic transmission) or depress the clutch (manual transmission). 4. Place the transfer case lever in the desired gear. f12_neutral_tcase 2H 4H N 4L Using the N (Neutral) position This position should only be used when towing the vehicle. Refer to Wrecker towing in the Roadside emergencies chapter. Do not leave the vehicle unattended with the transfer case in the N (Neutral) position.
Driving f12_ct_2h_4h Using the electronic shift 4WD system (if equipped) Positions of the electronic shift system 2H (2WD High) – Power to rear axle only. 4H (4WD High) – Power delivered to front and rear axles for increased traction. 4L (4WD Low) – Power to front and rear axles at low speeds. 4H 4L 2H Shifting from 2H (2WD High) to 4H (4WD High) Move the 4WD control to 4H at a stop or up to 88 km/h (55 mph).
f12_ct_4h_4l Driving Shifting from 4H (4WD high) to 2H (2WD high) Move the 4WD control to 2H at any forward speed. Shifting between 4H (4WD high) and 4L (4WD low) 1. Bring the vehicle to a stop. 2. Depress the brake. 3. Place the gearshift in N (Neutral) (automatic transmission) or depress the clutch (manual transmission). 4. Move the 4WD control to the 4H or 4L position.
Driving When using 4WD, maintain steering wheel control at all times, especially in rough terrain. Since sudden changes in terrain can result in abrupt steering wheel motion, make sure you grip the steering wheel from the outside. Do not grip the spokes. Drive cautiously to avoid vehicle damage from concealed objects such as rocks and stumps. You should either know the terrain or examine maps of the area before driving. Map out your route before driving in the area.
Driving solid area of the trail. Do not reduce the tire pressures but shift to a lower gear and drive steadily through the terrain. Apply the accelerator slowly and avoid spinning the wheels. f12_driving_mud_water Mud and water If you must drive through high water, drive slowly. Traction or brake capability may be limited. When driving through water, determine the depth; avoid water higher than the bottom of the hubs (if possible) and proceed slowly.
Driving that could damage drive components. If the transmission and transfer case are submerged in water, their fluids should be checked and changed, if necessary. If the rear axle is submerged in water, the rear axle lubricant should be checked and changed, if necessary. The rear axle is filled with a synthetic lubricant and does not normally require a lubricant change for the life of the vehicle. Rear axle lubricant quantities should not need to be checked unless a leak is suspected.
Driving When descending a steep hill, avoid sudden braking. Rapid pumping of the brake pedal will help slow the vehicle and still maintain steering control. When speed control is on and you are driving uphill, your vehicle speed may drop considerably, especially if you are carrying a heavy load. If vehicle speed drops more than 15–25 km/h (8–14 mph), the speed control will cancel automatically. Resume speed with accelerator pedal.
Driving steady pressure on the brake pedal. Allow more stopping distance and drive slower than usual. Consider using one of the lower gears. VEHICLE LOADING It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts.
Driving • • • • • equipment. Remember, the GVW is not a limit or a specification. Gross vehicle weight rating (GVWR): Maximum total weight of the base vehicle, passengers, optional equipment and cargo. The GVWR is specific to each particular vehicle and is listed on the Safety Compliance Certification Label on the driver door pillar. Gross axle weight rating (GAWR): Carrying capacity for each axle system (front and rear).
Driving ranges from zero to the maximum trailer weight rating. Remember to figure in the tongue load of your loaded trailer when figuring the total weight. Do not use replacement tires with lower weight capacities than the original because they may lower the vehicle’s GVWR and GAWR limitations. Replacement tires with a higher weight limit than the originals do not increase the GVWR and GAWR limitations. Calculating the load your vehicle can carry/tow 1.
Driving maximum trailer weight your vehicle can tow and must fall below the maximum shown under maximum trailer weight on the chart. Trailer towing table (F-150 4x2 automatic transmission) Engine Rear axle Maximum Maximum Maximum ratio GCWR kg (lb) trailer weight frontal area kg (lb) of trailer m2(ft2) Regular Cab F-150 4.2L 3.08 4,077 (9,000) 2,177 (4,800) 5.52 (60) 4.2L 3.55 4,530 (10,000) 2,582 (5,800) 5.52 (60) 4.6L 3.08 4,530 (10,000) 2,582 (5,700) 5.52 (60) 4.6L 3.55 5,209 (11,500) 3,261 (7,200) 5.
Driving Trailer towing table (F-150 4x2 manual transmission) 3.55 3,533 (7,800) 1,587 (3,500) 5.52 SuperCab F-150 4.2L 3.08 2,944 (6,500) 951 (2,100) 5.52 4.2L 3.55 3,533 (7,800) 1,540 (3,400) 5.52 4.6L 3.08 2,944 (6,500) 907 (2,000) 5.52 4.6L 3.55 3,533 (7,800) 1496 (3,300) 5.52 4.6L (60) (60) (60) (60) (60) Trailer tow table (F-150 4x4 automatic transmission) Engine Rear axle Maximum Maximum Maximum ratio GCWR kg (lb) trailer weight frontal area kg (lb) of trailer m2(ft2) Regular Cab F-150 4.2L 3.
Driving Trailer towing table (F-150 4x4 manual transmission) 4.2L 3.55 3,533 (7,800) 1,451 (3,200) 5.52 4.6L 3.08 2,944 (6,500) 816 (1,800) 5.52 4.6L 3.55 3,533 (7,800) 1,406 (3,100) 5.52 SuperCab F-150 4.6L 3.08 2,944 (6,500) 771 (1,700) 5.52 4.6L 3.55 3,533 (7,800) 1,360 (3,000) 5.52 (60) (60) (60) (60) (60) Trailer towing table (F-250 4x2 automatic transmission) Engine Rear axle Maximum Maximum Maximum ratio GCWR kg (lb) trailer weight frontal area kg (lb) of trailer m2(ft2) Regular Cab F-250 4.6L 3.
Driving 4.6L 4.6L Trailer towing table (F-250 4x2 manual transmission) 3.31 3,261 (7,200) 1,133 (2,500) 5.52 (60) 3.73 3,533 (7,800) 1,406 (3,100) 5.52 (60) Trailer towing table (F-250 4x4 automatic transmission) Engine Rear axle Maximum Maximum Maximum ratio GCWR kg (lb) trailer weight frontal area of kg (lb) trailer m2(ft2) Regular Cab F-250 4.6L 3.31 4,756 (10,500) 2,449 5.52 (60) (5,400) 4.6L 3.73 5,436 (12,000) 3,129 5.52 (60) (6,900) 5.4L 3.31 5,436 (12,000) 3,084 5.52 (60) (6,800) 5.4L 3.
Driving Trailer towing table (F-250 4x4 manual transmission) 3.73 3,533 (7,800) 1,224 5.52 (60) (2,700) SuperCab F-250 4.6L 3.31 3,261 (7,200) 952 (2,100) 5.52 (60) 4.6L 3.73 3,533 (7,800) 1,224 5.52 (60) (2,700) 4.6L f12_trailer TOWING A TRAILER Your vehicle may tow a class I, II or III trailer provided the maximum trailer weight is less than or equal to the maximum trailer weight listed for your engine and rear axle ratio on the above charts.
Driving Do not exceed the GVWR or the GAWR specified on the Safety Compliance Certification Label. Towing trailers beyond the maximum recommended gross trailer weight could result in engine damage, transmission/axle damage, structural damage, loss of control, and personal injury. Preparing to tow Use the proper equipment for towing a trailer, and make sure it is properly attached to your vehicle. See your dealer or a reliable trailer dealer if you require assistance.
Driving Using a load-equalizing hitch When hooking up a trailer using a load-equalizing hitch, always use the following procedure. 1. Park the unloaded vehicle on a level surface. With the ignition on and all doors closed, allow the vehicle to stand for several minutes so that it can level. 2. Turn the air suspension switch to OFF (if equipped). 3. Measure the height of a reference point on the front and rear bumpers at the center of the vehicle. 4.
Driving If it is necessary to relocate the trailer hitch ball position, a frame-mounted trailer hitch must be installed. Safety chains Always use safety chains between your vehicle and trailer. Cross chains under the trailer tongue and allow slack for turning corners. Connect safety chains to the vehicle frame or hook retainers. Never attach chains to the bumper. f12_safety_chains f12_trailer_brakes Trailer brakes Trailer brakes are required on most towed vehicles weighing over 680 kg (1,500 lbs).
Driving mph) with a trailer while towing in hilly country or on hot days. Speed control may shut off if you are towing on very long, steep grades. f12_when_you_tow When towing a trailer If equipped with an automatic transmission, use D (Drive) rather than D (Overdrive) while towing up or down steep hills. This will eliminate excessive downshifting and upshifting for optimum fuel economy and transmission cooling.
Driving • Allow more room for stopping with a trailer attached. • Practice turning, stopping and backing in an area before starting on a trip to get the feel of the vehicle/trailer combination. • When turning, drive slightly beyond the normal turning point so the trailer wheels will clear curbs and other obstacles. • When stopped in traffic for long periods of time in hot weather, place the automatic transmission gearshift in P (Park) to increase idle speed.
Driving Exceeding these limits may allow water to enter critical vehicle components, adversely affecting driveability, emissions and reliability. f12_service_towing Servicing when towing If you tow a trailer for long distances, your vehicle will require more frequent service intervals. Refer to the “Service Guide” for more information.
Driving • • • • • • vehicle, if necessary. Refer to the Safety Compliance Certification Label to find Front GAWR. The Front Axle Accessory Reserve Capacity and the Total Accessory Reserve Capacity listed on the bottom right of the Safety Compliance Certification Label will determine whether or not the addition of a snowplow will overload your vehicle. The weight of the snowplow and supporting components distributed to the front axle must not exceed the front accessory reserve capacity.
Driving These specifications are located in the vehicle’s Service Manual. Adherence to the toe and ride height specification is important for proper tire wear, ride, handling and headlight aim. Do not exceed the GVWR or the GAWR specified on the Safety Compliance Certification Label.
Driving Careless or high speed driving while plowing snow which results in vehicle decelerations equivalent to or greater than the air bag deployment impact speeds listed above can deploy the air bag. Such driving also increases the risk of accidents. All occupants of the vehicle, including the driver, should always wear their safety belts. Never remove or defeat the “tripping mechanisms” designed into the snow removal equipment by its manufacturer.
Driving If you are driving more then 24 km (15 miles) at temperatures above freezing, angle the plow blade either full left or full right to provide maximum airflow to the radiator. If you are driving less than 24 km (15 miles) at speeds up to 64 km/h (40 mph) in cold weather, you will not need to worry about blade position to provide maximum airflow. Transmission operation while plowing • Shift transfer case to 4L (4WD Low) when plowing in small areas at speeds below 8 km/h (5 mph).
Driving Do not spin the wheels at over 35 mph (55 km/h). The tires may fail and injure a passenger or bystander. FUEL CONSUMPTION Fuel economy can be improved by avoiding: • lack of regular, scheduled maintenance • excessive speed • rapid acceleration.
Roadside emergencies com_hazard_switch.01 HAZARD LIGHTS CONTROL Use only in an emergency to warn traffic of vehicle breakdown, approaching danger, etc. Depress to activate all indicators simultaneously. Depress again to switch off. The warning lights can be operated when the ignition is off. com_fuel_shut-off.01 FUEL PUMP SHUT-OFF SWITCH If the engine cranks but does not start after a collision, the fuel pump shut–off switch may have been activated.
Roadside emergencies REPLACING BLOWN FUSES If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken element. Check the appropriate fuses before replacing any electrical components. Even after a fuse is replaced, it may continue to blow if the cause of the overload is not identified and corrected. If a fuse continues to blow, have the vehicle’s electrical system checked. Standard fuse amperage ratings and colors Fuse rating 7.
Roadside emergencies f12_pass_comp_fuses Instrument panel fuses Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire.
Roadside emergencies Position 9 10 11 12 Amps 30 5 13 15 14 15 16 17 18 19 20 15 5 20 5 10 5 21 22 15 10 23 10 24 25 26 27 28 29 10 5 10 5 10 5 30 31 30 - 138 Description Not used Not used Wiper system On-board diagnostic (OBD II) data link connector Brake ON/OFF switch, rear anti-lock brake module and brake pressure switch Interior lamps and accessory delay relay GEM module/CTM module High beam headlamps Not used Instrument illumination Air bag diagnostic monitor, instrument cluster GEM modu
Roadside emergencies Position 1 2 3 4 5 Relays Description Interior lamps relay Battery saver relay Not used One touch down relay Accessory delay relay f12_eng_comp_fuses Power distribution box Lift cover towards left of vehicle to access the power distribution box. Always disconnect the battery before servicing high current fuses. Always replace the cover to the Power Distribution Box before reconnecting the battery or refilling fluid reservoirs.
Roadside emergencies Fuses Position 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 Position 1 2 140 Amps 15 30 15 25 60/20 50 40 30 30 20 50 50 50 40 30 30 30 - Description Parking and tail lamps Headlamps Daytime running lamps and fog lamps Auxiliary power point Not used Not used Not used 4WABS/rear anti-lock brake Air suspension compressor Trailer tow battery charge and stop/turn lamps 4WD transfer case shift motor and clutch Driver power seat Fuel pump Instrument panel fuse panel i
Roadside emergencies Position 1 2 3 4 5 6 Relays Description Windshield wipers HI/LO speed Windshield wipers run/park relay Washer pump relay Fuel pump relay Horn relay PCM power relay f12_megafuse Primary battery fuses (megafuses) Primary battery fuses are located under the PRIMARY BATTERY FUSE cover next to starter relay. Ford recommends that megafuses only be serviced by a qualified service technician.
Roadside emergencies f12_minifuses Engine minifuse panel The minifuse panel is located behind the power distribution box. 1 Location 1 2 3 4 5 6 Amperage 5 20 - 2 3 4 5 6 Description Powertrain control module (PCM) Trailer tow stop/turn lamps Not used Not used Not used Not used f12_flat_tires CHANGING FLAT TIRES If you get a flat tire while driving, do not apply the brakes heavily. Instead, gradually reduce the speed while holding the steering wheel firmly.
Roadside emergencies Tire change procedure 1. Park on a level surface. 2. Activate the hazard flashers. 3. Set the parking brake. 4. Place the gearshift in P (Park) (automatic transmission) or R (Reverse) (manual transmission). For 4WD vehicles equipped with Lever-operated transfer case, make sure that the lever is not in the N (Neutral) position. 5. Block the diagonally opposite wheel. 6. Remove the jack and lug wrench from under the passenger seat.
Roadside emergencies Removing spare from storage Your vehicle is equipped with a full-size spare tire. To remove the spare tire: 1. Carefully remove the jack handle from the retaining clips (above radiator in engine compartment).
Roadside emergencies 2. To lower the spare tire, insert the jack handle into the rear bumper opening and turn it counterclockwise. f12_removing_flat Removing flat tire and installing spare 1. Use the tip of the lug wrench to remove the wheel ornament. Insert the lug wrench tip into the notch in the wheel ornament. 2. Loosen the wheel nuts with the lug wrench. Do not remove the lug nuts yet. 3. Position the jack as shown for your specific vehicle (4WD or 2WD).
Roadside emergencies • Front (4WD) • Rear Never use the differential as a jacking point.
Roadside emergencies 4. Raise the vehicle high enough for the spare tire to clear the ground when installed. 5. Remove the wheel lug nuts. 6. Remove the flat tire and install the spare. 7. Install the lug nuts and tighten until the wheel is seated. Installing wheels without a good metal-to-metal contact at the wheel mounting surface can cause the wheel lug nuts to loosen and could allow the wheel to come off while the vehicle is in motion.
Roadside emergencies 9. To stow the flat tire, lay the tire on the ground with the inboard side facing up. Install the retainer through the wheel center and slide the wheel under the vehicle. Turn the spare handle clockwise until the tire is raised to its original position underneath the vehicle. The spare handle ratchets when the tire is raised to the stowed position. It will not allow you to overtighten. 10. Unblock the wheel. 11.
Roadside emergencies Batteries contain sulfuric acid which burns skin, eyes, and clothing. 4 1 + – – + CONNECTING THE JUMPER CABLES 1. Position the vehicles so that they do not touch one another. 2. Switch off the engine. Switch off any unnecessary electrical equipment. 3. Connect the positive (+) terminal of the discharged battery (1) to the positive (+) terminal of the booster battery (2). 4.
Roadside emergencies JUMP STARTING 1. Start the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the vehicle with the discharged battery. 3. Once the engine has been started, run both vehicles for a further three minutes before disconnecting the leads. 150 4 + – + WRECKER TOWING It is recommended that your vehicle be towed with wheel lift and dollies or flatbed equipment. Do not tow with slingbelt equipment.
Roadside emergencies Ford recommends using one of the above methods for towing. f12_recreational_towing Recreational towing (all wheels on the ground) Follow these guidelines for your specific powertrain combination to tow your vehicle with all four wheels on the ground (such as behind a recreational vehicle). These guidelines are designed to ensure that your transmission is not damaged due to insufficient lubrication. 2WD (manual and automatic transmissions) 1. Place transmission in N (Neutral).
Roadside emergencies 2. Maximum speed is 56 km/h (35 mph). 3. Maximum distance is 80 km (50 miles). If a distance of 80 km (50 miles) or a speed of 56 km/h (35 mph) must be exceeded, you must disconnect the rear driveshaft. With the rear driveshaft disconnected, the maximum speed is 88 km/h (55 mph) and there are no mileage restrictions. See your dealer for help with disconnecting the driveshaft. 4WD – Lever operated transfer case (manual and automatic transmissions) 1. Place transmission in P (Park). 2.
Roadside emergencies 4. Maximum speed is 56 km/h (35 mph). 5. Maximum distance is 80 km (50 miles). If a distance of 80 km (50 miles) or a speed of 56 km/h (35 mph) must be exceeded, you must disconnect the rear driveshaft. With the rear driveshaft disconnected, the maximum speed is 88 km/h (55 mph) and there are no mileage restrictions. See your dealer for help with disconnecting the driveshaft.
Maintenance and care com_service_recommendations.01 SERVICING YOUR VEHICLE Service recommendations To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easy location. • As possible, we design parts that can be replaced without tools. • We provide you with a “Service Guide” which makes tracking routine service for your vehicle easy. If your vehicle requires professional service, your dealership can provide necessary parts and service.
Maintenance and care could get caught in moving parts. Take precautions with long hair. • Do not work on a vehicle with the engine running in an enclosed space, unless you are sure you have enough ventilation. • Keep all lit cigarettes, open flames and other lit material away from the battery and all fuel related parts. If you disconnect the battery, the engine must “relearn” its idle conditions before your vehicle will drive properly, as explained in Battery in this chapter. com_working_off.
Maintenance and care 1. Set the parking brake fully and ensure the gearshift is securely latched in P (Park). 2. Block the wheels to prevent the vehicle from moving unexpectedly. Do not start your engine with the air cleaner removed and do not remove it while the engine is running. • Manual transmission 1. Set the parking brake, depress the clutch and place the gearshift in 1 (First). 2. Block the wheels to prevent the vehicle from moving unexpectedly.
Maintenance and care Opening the hood 1. Inside the vehicle, pull the hood release handle located under the bottom left corner of the instrument panel. HOOD 2. While applying downward pressure on the hood, push the hood latch handle located just left of the center of the hood. 3. Lift the hood. After closing the hood, try to lift it to be sure that it is closed securely. Lubricate the hood latch every six months to ensure proper operation. f12_4.
Maintenance and care 3 1 12 11 4.2L engine 1. Battery 2. Engine oil filler 3. Engine oil dipstick 4. Clutch fluid reservoir (if equipped) 5. Brake master cylinder 6. Power distribution box 7. Engine coolant recovery reservoir 8. Radiator cap 9. Air cleaner 10. Power steering fluid reservoir 11.
Maintenance and care 12. Windshield washer fluid reservoir 1 2 3 12 f12_4.6L_5.4L_engine 4 6 5 11 10 7 9 8 4.6/5.4L engine 1. Battery 2. Automatic transmission dipstick (if equipped) 3. Engine oil filler 4. Engine oil dipstick 5. Clutch fluid reservoir (if equipped) 6. Brake master cylinder 7. Power distribution box 8. Engine coolant recovery reservoir 9. Air cleaner 10.
Maintenance and care 11. Power steering fluid reservoir 12. Windshield washer fluid reservoir f12_engine_oil f12_oil_specs ENGINE OIL Oil specifications Use WSS-M2C153–F motor oil CERTIFIED FOR GASOLINE ENGINES by the American Petroleum Institute. Engine oils with an SAE 5W-30 viscosity and displaying the American Petroleum Institute certification mark are preferred for your vehicle. They provide the best engine performance, fuel economy and engine protection for all climates down to –25°C (-15°F).
Maintenance and care Oil filters Ford production and aftermarket (Motorcraft) oil filters are designed for added engine protection and long life. If a replacement oil filter is used that does not meet Ford material and design specifications, startup engine noises or knock may be experienced. It is recommended that you use the appropriate Motorcraft oil filter (or another brand meeting Ford specifications) for your engine application.
Maintenance and care engine oil dipstick (4.2L and 4.6L/5.4L engines shown). • 4.2L engine MIN MAX • 4.6L/5.4L engine MIN 5. Wipe the dipstick clean. Insert the dipstick fully, then remove it again. The oil level should be in the range shown on the dipstick. 6. If the oil level is below the minimum line, add engine oil as necessary. If the oil level is below the MIN line, add engine oil as necessary.
Maintenance and care the MAX line, engine damage or high oil consumption may occur and some oil must be removed from the engine by a service technician. 7. Put the dipstick back in and ensure it is fully seated. f12_adding_oil Adding engine oil 1. Check the engine oil. 2. If the oil level is below the MIN line, then add engine oil. 3. Remove the yellow oil filler cap. 4. Use a funnel to add oil through the opening. Make sure you use a certified engine oil of the preferred viscosity. 5.
Maintenance and care com_checking-adding_fluid.01 BRAKE FLUID CHECKING AND ADDING BRAKE FLUID Brake fluid should be checked and refilled as needed at least once each year: • Clean the reservoir cap before removal to prevent dirt or water from entering the reservoir. • Visually inspect the fluid level. • If necessary, add brake fluid until the level reaches MAX. Do not fill above this line. • Use only a DOT 3 brake fluid certified to meet Ford specifications.
Maintenance and care Do not let the reservoir for the master cylinder run dry. This may cause the brakes to fail. f12_clutch_fluid CHECKING AND ADDING CLUTCH FLUID (IF EQUIPPED) During normal operation, the fluid level in the clutch reservoir will slowly rise. If the fluid level drops, maintain the fluid level at the step in the reservoir. Use only a DOT 3 brake fluid designed to meet Ford specifications. Refer to Capacities and specifications. 1.
Maintenance and care CHECKING AND ADDING WINDSHIELD WASHER FLUID 1. Lift the washer fluid reservoir cover. 2. Add washer fluid intil the level reaches the FULL line. Use only fluid that meets Ford Specifications. Refer to Capacities and specifications. The addition of a bug shield to the front of the vehicle may adversely affect the washer system from delivering fluid to the windshield. Devices such as bug shields are not recommended. Windshield washer fluid contains methanol and it is poisonous.
Maintenance and care CHECKING AND ADDING ENGINE COOLANT f12_adding_coolant Adding engine coolant Do not put engine coolant in the container for the windshield washer fluid. If sprayed on the windshield, engine coolant could make it difficult to see through the windshield. When the engine is cool, add a 50/50 mixture of engine coolant and water to the engine coolant recovery reservoir – DO NOT ADD DIRECTLY TO THE RADIATOR.
Maintenance and care If you must remove the coolant recovery cap, follow these steps to avoid personal injury: 1. Before you remove the cap, turn the engine off and let it cool. 2. When the engine is cool, wrap a thick cloth around the cap. Slowly turn cap counterclockwise to the first stop. 3. Step back while the pressure releases. 4. When you are sure that all the pressure has been released, use the cloth to press the cap down, turn it counterclockwise and remove it.
Maintenance and care Recycled engine coolant Ford Motor Company recommends that Ford and Lincoln-Mercury dealers use recycled engine coolant produced by Ford-approved processes. Not all coolant recycling processes produce coolant which meets Ford specification ESE-M97B44–A, and use of such coolant may harm engine and cooling system components. Always dispose of used automotive fluids in a responsible manner. Follow your community’s regulations and standards for recycling and disposing of automotive fluids.
Maintenance and care freeze at the temperature level in which you drive during winter months. Never increase the engine coolant concentration above 60%. Leave a 50/50 mixture of engine coolant and water in your vehicle year-round in non-extreme climates. com_checking_hoses.01 Checking the cooling system hoses Inspect all engine and heater system hoses and hose connections for: • deterioration • leaks • loose hose clamps What you should know about fail-safe cooling (if equipped) Vehicles equipped with 4.
Maintenance and care cooling mode. If the engine coolant supply is depleted, this feature allows the driver to drive the vehicle (with limited power) for a short distance in order to get the vehicle to a service facility. Take your vehicle to a service facility as soon as possible to minimize engine damage. The actual distance your vehicle can be driven depends on vehicle load, road conditions and outside temperature.
Maintenance and care soon as possible to minimize engine damage. When fail-safe mode is activated • Pull off the road as soon as possible. • Immediately turn the engine off to prevent severe engine damage. • Wait for the engine to cool. • Check the coolant level. f12_power_steering CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid level at least twice a year. 1. Start the engine.
Maintenance and care 2. When the engine coolant temperature gauge reaches the normal zone, turn the engine off. MAX MIN MAX MIN 3. Visually inspect the fluid level in the power steering fluid reservoir. 4. Add power steering fluid until the fluid level reaches MAX. Use only fluid that meets Ford specifications. Refer to Capacities and specifications.
Maintenance and care Before adding any fluid, make sure the correct type will be used. This information is indicated on the dipstick. Do not drive the vehicle if the fluid level is below the bottom hole on the blade type dipstick (4R70W transmission) or below the COLD area on the bullet type dipstick (E4OD transmission) and outside temperatures are above 10°C (50°F). Your vehicle does not use up transmission fluid. However, it is recommended that you check the transmission fluid at least twice a year.
Maintenance and care 1. Park the vehicle on a level surface. 2. Start the engine and move the gearshift lever through all of the gear ranges. Allow sufficient time for each gear to engage. 3. Latch the gearshift lever in P (Park), set the parking brake and leave the engine running. 4. Remove the dipstick, wiping it clean with a clean, dry rag. 5. Install the dipstick. 6. Remove the dipstick and inspect the fluid level.
Maintenance and care between the holes near the bottom of the indicator. • For E4OD transmissions, the fluid level should be within the HOT area, or if the vehicle has not been driven, within the COLD area. 7. If necessary, add fluid in .25L (1/2 pint) increments through the filler tube until the level is at the correct area on the dipstick. If an overfill occurs, excess fluid should be removed by a qualified technician.
Maintenance and care Checking and adding manual transmission fluid (if equipped) 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Fluid level should be at bottom of the opening. 4. Add only enough fluid through the filler opening so that the fluid level is 6 mm (3/8 in) from the bottom of the opening. Use only fluid that meets Ford specifications. Refer to the Capacities and specifications chapter.
Maintenance and care Checking and adding transfer case fluid 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Add only enough fluid through the filler opening so that the fluid level is at the bottom of the opening. Use only fluid that meets Ford specifications. Refer to the Capacities and specifications chapter.
Maintenance and care replacing, it may be replaced with a low-maintenance battery. For information on replacement batteries, refer to Motorcraft part numbers in the Capacities and specifications chapter. The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Batteries contain sulfuric acid which burns skin, eyes, and clothing.
Maintenance and care have the charging system checked for a possible malfunction. Your vehicle is equipped with a battery saver feature designed to prevent your battery from accidental wear down due to doors left ajar. For information on this system, refer to the Controls and features chapter. Relearning idle conditions Because your vehicle’s engine is electronically controlled by a computer, some control conditions are maintained by power from the battery.
Maintenance and care preset radio stations must be reset once the battery is reconnected. • Always dispose of used automotive batteries in a responsible manner. Follow your community’s standards for disposal. Call your local recycling center to find out more about recycling automotive batteries. f12_changing_air_filter CHANGING THE AIR FILTER 1. Loosen the clamp that secures the air cleaner in place. 2. Separate the two halves of the air cleaner. 3.
Maintenance and care 1. Pull the arm away from the windshield and lock it into the service position. 2. Turn the blade at an angle from the wiper arm. Depress lock tab and push wiper mounting arm away from wiper blade assembly. 3. Attach new wiper blade by pulling wiper mounting arm down on wiper blade until lock tab is engaged. f12_maint_tires com_about_tire_grades.
Maintenance and care about tire grades exactly as the government has written it. com_treadwear.01 Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire grade 150 would wear one and one-half (1 1/2) times as well on the government course as a tire grade 100.
Maintenance and care controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law.
Maintenance and care hour or driven less than 5 km [3 miles]). The cold pressure amount is listed on the Safety Compliance Certification Label located on the inside driver door latch pillar. Improperly inflated tires can affect vehicle handling and can fail suddenly, possibly resulting in loss of vehicle control. f12_rotating_tires Rotating the tires Rotate your tires at regular intervals to ensure even wear. Refer to the following diagrams for rotation cycles.
f12_replacing_tires Maintenance and care proper alignment when remounting. • Four-tire rotation • Five-tire rotation Replacing the tires Replace the tires when the wear band is visible through the tire treads.
Maintenance and care When replacing full size tires, never mix radial, bias-belted, or bias-type tires. Use only the tire sizes that are listed on the tire pressure decal. Make sure that all tires are the same size, speed rating, and load-carrying capacity. Use only the tire combinations recommended on the decal. If you do not follow these precautions, your vehicle may not drive properly and safely. Make sure that all replacement tires are of the same size, type, load-carrying capacity and tread design (e.
Maintenance and care Snow tires and chains Snow tires must be the same size and grade as the tires you currently have on your vehicle. The tires on your vehicle have all weather treads to provide traction in rain and snow. However, in some climates, you may need to use snow tires and chains. Follow these guidelines when using snow tires and chains. • Use only SAE Class “S” chains. • Install chains securely, verifying that the chains do not touch any wiring, brake lines or fuel lines.
Maintenance and care these components from your vehicle when using snow tires and chains. f12_fuel_info com_important_precautions.06 FUEL Important safety precautions Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire. If you do not use the proper fuel cap, the pressure in the fuel tank can damage the fuel system or cause it to work improperly in a collision. The fuel system may be under pressure.
Maintenance and care Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before fueling your vehicle. • Always turn off the vehicle before fueling. • Automotive fuels can be harmful or fatal if swallowed. If fuel is swallowed, call a physician immediately, even if no symptoms are immediately apparent. The toxic affects of fuel may not be visible for hours. • Fuels can also be harmful if absorbed through the skin.
Maintenance and care vehicle. The damage may not be covered by your warranty. Your vehicle was not designed to use fuel containing manganese-based additives such as MMT. Additionally, vehicles certified to California emission standards (indicated on the underhood Vehicle Emissions Control Information label) are designed to operate on California reformulated gasolines. If California reformulated gasoline is not available when you refuel, your vehicle can be operated on non-California fuels.
Maintenance and care your dealer or a qualified service technician to prevent any engine damage. Fuel quality If you are experiencing starting, rough idle or hesitation problems try a different brand of fuel. If the condition persists, see your dealer or a qualified service technician. The American Automobile Manufacturers Association (AAMA) issued a gasoline specification to provide information on high quality fuels that optimize the performance of your vehicle.
Maintenance and care 2. Each time you fill the tank, record the amount of fuel added (in liters or gallons). 3. After at least three to five fuel tank fill-ups, fill the fuel tank and record the current mileage reading. 4. Use one of the following equations to calculate fuel economy. Liters used x 100 4 Total kilometers traveled = km/liter. Total miles traveled 4 Total gallons used = mpg. 5. Keep a record for at least one month. This will provide an accurate estimate of the vehicle’s fuel economy.
Maintenance and care WHAT YOU SHOULD KNOW ABOUT THE EMISSION CONTROL SYSTEM Your vehicle is equipped with a catalytic convertor which enables your vehicle to comply with applicable exhaust emission requirements. For more information on your vehicle’s emission control system, see the Vehicle Emission Control Information decal located on the left side of the engine compartment. Follow these guidelines to ensure proper emission system operation: • Use only unleaded fuel. • Avoid running out of fuel.
Maintenance and care Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire. If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately. Do not drive if you smell exhaust fumes.
Maintenance and care Important emission control information By law, anyone who manufacturers, repairs, services, sells, leases, trades vehicles or supervises a fleet of vehicles is not permitted to intentionally remove an emission control device or prevent it from working. Do not make any unauthorized changes to the vehicle or engine. Changes that cause more unburned fuel to reach the exhaust system can increase the temperature of the engine or exhaust system.
Maintenance and care • 20 minutes of driving in stop and go city-type traffic with at least four idle periods. • 10 minutes of driving on an expressway or highway. Before completing the above driving modes, the engine must be warmed up and at operating temperature. Once started, the vehicle must not be turned off during the above driving modes.
Maintenance and care f12_replacing_bulbs REPLACING BULBS Replacing exterior bulbs It is a good idea to check the operation of the following lamps frequently: • Headlamps • Tail lamps • Brakelamps • High-mount brakelamp • Backup lamps • Hazard flashers • Turn signals • License plate lamp • Fog lamps • Interior overhead lamps 198
Maintenance and care Do not remove lamp bulbs unless they will be replaced immediately. If a bulb is removed for an extended period of time, contaminants may enter the lamp and affect performance. f12_headlamps_turnsignals Replacing headlamp bulbs Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated. 1.
Maintenance and care 4. Slide headlamp assembly forward and off of guide ribs to expose the back of the bulb and wiring connector. 5. Remove the electrical connector from the bulb by grasping the wire and pulling it rearward. 6. Remove bulb retainer ring by turning it counterclockwise about 1/4 turn, then slide the ring off the plastic base. 7. Without turning, carefully pull bulb assembly out of headlamp assembly. 8. Insert the glass end of the new bulb into the headlamp assembly socket.
Maintenance and care 11. Straighten alignment pins, making them parallel with the outer edges of the attachment standoff. 12. Carefully insert the headlamp assembly into the vehicle making sure the alignment pins are inserted into the proper holes and into the guide ribs. 13. Hold the headlamp assembly snugly against the vehicle and push down on the clips to lock the lamp into position. Replacing parking lamp/turn signal bulbs 1. Remove screw from the top of lamp assembly.
Maintenance and care 2. Disengage lamp assembly (it has a snap fit). 3. Remove the electrical connector from the bulb by grasping the wire and pulling it rearward. 4. Remove bulb retainer ring by turning it counterclockwise about 1/4 turn, then slide the ring off the plastic base. 5. Without turning, carefully pull bulb assembly out of parking lamp assembly. 6. Insert the glass end of the new bulb into the parking lamp assembly socket.
Maintenance and care into the rear of the plastic base until it “snaps.” 9. Align top and bottom ribs of parking lamp assembly with corresponding slots on front of vehicle. 10. Push gently until parking lamp assembly seats (you will hear a snap). 11. Replace screw removed in step 1. f12_foglamps Replacing foglamp bulbs 1. Disconnect the electrical connector from the back of the foglamp assembly. 2. Twist, then pull the bulb from the foglamp assembly. 3. Install the new bulb. 4.
Maintenance and care Replacing tail lamp/backup lamp bulbs 1. Remove the two bolts from the inside of the tailgate. 2. Carefully pull the tail lamp and backup lamp assembly from the tailgate pillar by releasing the two retaining tabs. 3. Disconnect the bulb connector. 4. Pull out the bulb to be replaced. 5. Install a new bulb. 6. Carefully insert the tail lamp and backup lamp assembly, snapping the two retaining tabs into place. 7. Install the two bolts. Replacing license plate lamp bulbs 1.
Maintenance and care Replacing dome lamp bulb (if equipped) 1. Carefully pull the dome lamp lens from the lamp assembly. 2. Remove the dome lamp bulb and replace it with a new bulb. 3. Carefully snap the dome lamp lens into the dome lamp assembly. f12_dome_map_lamp Replacing dome/map lamp bulb (if equipped) 1. Carefully pull the dome/map lamp lens from the lamp assembly. 2. Remove the dome/map lamp bulb and replace it with a new bulb. 3. Carefully snap the dome lamp lens into the dome/map lamp assembly.
Maintenance and care Exterior bulb specifications Function Front park/turn lamps Foglamps Headlamps Rear turn/sidemarker Number of bulbs 2 2 2 2 Trade number 3157NAK 9006 9007 3157NAK f12_aiming_hlamps AIMING HEADLAMPS The alignment of your headlamps should be checked if: • Oncoming motorists frequently signal you to turn off your vehicle’s high beams when you do not have the high beams on. • The headlamps do not seem to give you enough light to see clearly at night.
Maintenance and care Washing your vehicle Wash your vehicle regularly with cold or lukewarm water. Never use strong detergents or soap. If your vehicle is particularly dirty, use a quality car wash detergent. Always use a clean sponge, washing glove or similar device and plenty of water for best results. To avoid spots, avoid washing when the hood is still warm, immediately after or during exposure to strong sunlight. During winter months, it is especially important to wash the vehicle on a regular basis.
Maintenance and care Repairing paint chips Minor scratches or paint damage from road debris may be repaired with touch-up paint, paint repair foil or aerosol paint spray from the Ford accessory line. Observe the application instructions on the products. Remove particles such as bird droppings, tree sap, insect remains, tar spots, road salt and industrial fallout immediately. f12_cleaning_wheels Cleaning the wheels Wash the wheels with the same detergent you use to clean the body of your vehicle.
Maintenance and care dirt buildup act as insulators and keep the engine warmer than normal. Follow these guidelines to clean your engine: • Take care when using a power washer to clean the engine. The high pressure fluid could penetrate the sealed parts and cause damage. • Do not spray with cold water to avoid cracking the engine block. • Cover the highlighted areas to prevent water damage when cleaning the engine.
Maintenance and care plastic parts with thinners, solvents or petroleum-based cleaners. Cleaning the exterior lamps Wash the exterior lamps with the same detergent you used to wash the exterior of your vehicle. Use glass cleaner or tar remover if necessary. To avoid scratching the lamps, do not use a dry paper towel, chemical solvents or abrasive cleaners to clean the lamps.
Maintenance and care Cleaning the instrument panel Clean instrument panel with a damp cloth, then dry with a dry cloth. Any cleaner or polish that increases the gloss of the upper portion of the instrument panel should be avoided. The dull finish in this area is to help protect the driver from undesirable windshield reflection. com_int_fabric_cleaning.01 Cleaning the interior fabric Remove dust and loose dirt with a whisk broom or a vacuum cleaner. Remove fresh spots immediately.
Maintenance and care Cleaning and maintaining the safety belts Clean the safety belts with a mild soap solution recommended for cleaning upholstery or carpets. Do not bleach or dye the belts, because these actions may weaken the belt webbing. Check your safety belt system periodically to make sure that it works properly and is not damaged. If the webbing shows any wear, nicks or cuts, have it examined by a qualified technician to determine if replacement is necessary.
Capacities and specifications f12_motorcraft_part MOTORCRAFT PART NUMBERS Component Spark plug-platinum1 Air filter Fuel filter Oil filter PCV valve 4.2L AWSF-42EE Engine 4.6L AWSF-32PP 5.
Capacities and specifications Fluid Axle; rear Engine coolant Engine oil1 Ford part name Ford 26.03 cm (10.25 in) Conventional and Traction Lok (2) Premium Cooling System Fluid Super Premium Motorcraft Motor Oil 5W-30 Unleaded 87 octane Fuel Motorcraft MERCONT Multi-purpose ATF Motorcraft Transfer MERCONT case Multi-purpose fluid 3(if equipped) ATF Motorcraft Transmission MERCONT fluid; Multi-purpose automatic ATF Power steering fluid 214 Vehicle type Capacity F-250 3.3L (7.0 pts.) 4.
Capacities and specifications Ford part Vehicle type Capacity name Motorcraft 5-speed manual 3.5L (3.75 qts.) Transmission MERCONT fluid; Multi-purpose manual2 ATF Ultra-clear All 4.0L (4.25 qts.) Windshield windshield washer fluid washer fluid concentrate (1) Add 118 ml (4 oz.) of additive friction modifier C8AZ-19B546-A, Ford specification EST-M2C118–A, for complete fill of 22.35 cm (8.8 in.) and 24.76 cm (9.75 in) ring gear Traction-Lok axles. (2) Add 236 ml (8 oz.
Capacities and specifications Fluid Brake fluid and clutch fluid Engine coolant Engine oil Grease; body hinges, latches and seat tracks. Grease; transmission /steering/parking brake linkages and pivots. Brake and clutch pedal shaft.
Capacities and specifications f12_engine_data ENGINE DATA General Specifications Displacement Bore x stroke Horsepower Torque Required fuel grade Induction system Firing order Spark plug gap Ignition system Compression ratio OHV 4.2L V-6 4.2 L (256.2 CID) 96.8 mm x 95.0 mm 205 @ 4750 RPM 260 ft. lb. @ 3000 RPM Unleaded - 87 octane Split port, OHV 1-4-2-5-3-6 .137 cm (.054 in) E.I. 9.2:1 Engine SOHC 4.6L V8 4.6 L (280.6 CID) 90.2 mm x 90 mm 210 @ 4400 RPM 290 ft. lb.
Capacities and specifications D E f12_styleside VEHICLE DIMENSIONS STYLESIDE Dimension A=Overall height B=Track front/rear C=Overall width D=Wheel base 218 Regular Cab 4x2 1.84 m (72.7 in) (SWB) 1.83 m (72.4 in) (LWB) 1.66 m (65.4 in)/1.66 m (65.4 in) 1.99 m (78.4 in) 3.04 m (119.9 in)(SWB) 3.51 m (138.5 in)(LWB) Body Regular Cab 4x4 1.91 m (75.5 in) (SWB) 1.90 m(75.1 in) (LWB) 1.66 m (65.4 in)/1.66 m (65.4 in) 1.99 m (78.4 in) 3.04 m (119.9 in)(SWB) 3.51 m (138.5 in)(LWB) Style Super Cab 4x2 1.
Capacities and specifications Dimension E=Overall length Regular Cab 4x2 5.13 m (202.2 in)(SWB) 5.60 m (220.8 in)(LWB) Body Regular Cab 4x4 5.13 m (202.2 in)(SWB) 5.60 m (220.8 in)(LWB) Style Super Cab 4x2 5.6 m (220.8 in)(SWB) 6.11 m (240.9 in)(LWB) Super Cab 4x4 5.6 m (220.8 in)(SWB) 6.11 m (240.9 in)(LWB) f12_flareside FLARESIDE Dimension A=Overall height B=Track front/rear C=Overall width D=Wheel base E=Overall length Regular Cab 4x2 1.84 m (72.7 in) 1.66 m (65.4 in) 2.00 m (79.1 in) 3.
Reporting safety defects f12_reporting REPORTING SAFETY DEFECTS If you believe that your vehicle has a defect that could cause a crash, or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to Ford Motor Company. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
