Contents Before driving Introduction 2 Instrumentation 4 Controls and features 16 Seating and safety restraints 63 Starting and driving Starting 83 Driving 88 Roadside emergencies 108 Servicing Maintenance and care 126 Capacities and specifications 177 Reporting safety defects 185 Index 186 All rights reserved.
Introduction ICONS Indicates a safety alert. Read the following section on Warnings. Indicates vehicle information related to recycling and other environmental concerns will follow. Correct vehicle usage and the authorized disposal of waste cleaning and lubrication materials are significant steps towards protecting the environment. Indicates a message regarding child safety restraints. Refer to Seating and safety restraints for more information.
Introduction INFORMATION ABOUT THIS GUIDE The information found in this guide was in effect at the time of printing. Ford may change the contents without notice and without incurring obligation. SPECIAL NOTICES Notice to owners of Cobra vehicles Before you drive your vehicle, be sure to read the “SVT Cobra Owner’s Guide Supplement.” This book contains important operation and maintenance information.
Instrumentation Instrument cluster (pg. 6) Headlamp control (pg. 16) 60 50 40 C H 30 70 80 90 100 20 10 3 130 220 240 20 km/h MPH 150 L 7 0 SELECT/RESET SERVICE ENGINE SOON H 8 0 0 0 0 0 0 .0 L F AIR THEFT BAG LOW FUEL HI LO OFF 4 6 140 REAR DEF Turn signal and wiper/washer control (pg. 43) 5 2 1 FUEL DOOR E 4 RPMX1000 120 140 110 100 160 80 180 120 200 60 40 Driver side air bag (pg.
Instrumentation Electronic sound system (pg. 21) VENT OFF FLOOR MIX LO NORM A/C MAX A/C HI FM1 REW AUTOMATIC DNR CrO2 ST FF PLAY EJCT PROG POWER AUDIO VOLUME AM/FM 1 2 3 4 5 CLOCK AUTO PRESET SCAN TUNE SEEK Climate control systems (pg.
Instrumentation WARNING LIGHTS AND CHIMES Base instrument cluster 60 70 50 40 C H 80 100 120 2 100 160 40 20 RPMX1000 5 SELECT/RESET 7 1 120 MPH km/h L 6 180110 20 10 0 H 0 0 0 0 0 0 .0 FUEL DOOR E 4 3 80 90 140 60 30 F L AIR THEFT BAG SERVICE ENGINE SOON LOW FUEL O/D OFF H BRAKE ! P ABS Optional instrument cluster 60 50 40 C H 30 70 80 90 60 200 40 220 20 10 130 240 20 MPH km/h 5 RPMX1000 2 6 1 7 L H 140 150 0 SELECT/RESET 8 0 0 0 0 0 0 .
Instrumentation High beams Illuminates when the high beam headlamps are turned on. Safety belt Momentarily illuminates when the ignition is turned to the ON position to remind you to fasten your safety belts. For more information, refer to the Seating and safety restraints chapter. Charging system Illuminates when the ignition is turned to the ON position and the engine is off. The light also illuminates when the battery is not charging properly, requiring electrical system service.
Instrumentation Service engine soon Your vehicle is SERVICE ENGINE equipped with a SOON computer that monitors the engine’s emission control system. This system is commonly known as the On Board Diagnostics System (OBD II). The OBD II system protects the environment by ensuring that your vehicle continues to meet government emission standards. The OBD II system also assists the service technician in properly servicing your vehicle.
Instrumentation consists of a cold engine startup followed by mixed city/highway driving.) No additional vehicle service is required. If the Service Engine Soon light remains on, have your vehicle serviced at the first available opportunity. Light is blinking: Engine misfire is occurring which could damage your catalytic converter. You should drive in a moderate fashion (avoid heavy acceleration and deceleration) and have your vehicle serviced at the first available opportunity.
Instrumentation control switch is depressed or if the light flashes when you are driving, have your vehicle serviced. Traction ControlY active This light momentarily illuminates when the ignition is turned to ON. It also illuminates when the Traction Controly system begins applying and releasing the brakes and adjusting the engine characteristics to limit a wheelspin condition. It will be lit for a minimum of four seconds or for the duration of the Traction Controly event.
Instrumentation Check coolant Illuminates when the coolant level in the coolant reservoir is low and more needs to be added. This lamp will also illuminate when the ignition is turned to ON and the engine is off. For more information on adding engine coolant, refer to Engine coolant in the Maintenance and care chapter. Safety belt warning chime Chimes to remind you to fasten your safety belts. For information on the safety belt warning chime, refer to the Seating and safety restraints chapter.
Instrumentation GAUGES Base instrument cluster gauges 50 40 C H 60 70 80 100 120 100 160 40 20 2 RPMX1000 5 SELECT/RESET 7 1 6 180110 20 10 120 MPH 0 km/h L H 0 0 0 0 0 0 .
Instrumentation Engine coolant temperature gauge Indicates the C H temperature of the engine coolant. At normal operating temperature, the needle remains within the normal area (the area between the “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine immediately and let the engine cool. Refer to Engine coolant in the Maintenance and care chapter. Never remove the coolant reservoir cap while the engine is running or hot.
Instrumentation Odometer Registers the total kilometers (miles) of the vehicle. 4 3 5 RPMX1000 2 6 0 8 1 7 SELECT/RESET 0 0 0 0 0 0 .0 Tachometer Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer at the top of the scale or in the red zone may damage the engine. • Base instrument 4 3 cluster RPMX1000 2 5 1 6 0 SELECT/RESET 7 0 0 0 0 0 0 .0 • Standard instrument cluster 3 4 5 RPMX1000 6 2 1 7 0 SELECT/RESET 0 0 0 0 0 0 .
Instrumentation Trip odometer Registers the kilometers (miles) of individual journeys. Press the reset button until a “T” appears in the display (this represents the trip mode). Press and hold the button for 2.5 seconds to reset. 3 4 5 RPMX1000 2 6 0 8 1 7 SELECT/RESET 0 0 0 0 0 0 .0 Battery voltage gauge This gauge shows the L H battery voltage when the ignition is in the ON position.
Controls and features HEADLAMP CONTROL • Pull the headlamp control toward you to the first position to turn on the parking lamps, tail lamps, license plate lamps and marker lamps. • Pull the headlamp control toward you to the outer position to turn on the headlamps (in addition to the previous lamps). Daytime running lamps (DRL) (if equipped) Turns the headlamps on with a reduced output.
Controls and features PANEL DIMMER CONTROL To adjust the brightness of the instrument panel: • Rotate clockwise/ counterclockwise when the headlamp control is in the parking lamp or low-beam position. To turn on the courtesy lamps: • Rotate fully counterclockwise. REAR WINDOW DEFROSTER (IF EQUIPPED) The rear defroster REAR DEF control is located on the instrument panel. Press the rear defroster control to clear the rear window of thin ice and fog.
Controls and features CLIMATE CONTROL SYSTEM Manual heating and air conditioning system VENT OFF FLOOR MIX LO NORM A/C HI MAX A/C Fan speed control Controls the volume of air circulated in the vehicle. LO HI Temperature control knob Controls the temperature of the airflow inside the vehicle. Mode selector control Controls the direction of the airflow to the inside of the vehicle. VENT OFF FLOOR MIX NORM A/C MAX A/C The air conditioning compressor will operate in all modes except VENT and FLR.
Controls and features Under normal conditions, your vehicle’s climate control system should be left in any position other than MAX A/C or OFF when the vehicle is parked. This allows the vehicle to “breathe” through the outside air inlet duct. • MAX A/C-Uses recirculated air to cool the vehicle. MAX A/C is noisier than NORM A/C but more economical and will cool the inside of the vehicle faster. Airflow will be from the instrument panel registers.
Controls and features is about 10°C (50°F) or higher, the air conditioner will automatically dehumidify the air to reduce fogging. • - Distributes outside air through the windshield defroster ducts. It can be used to clear ice or fog from the windshield. If the temperature is about 10°C (50°F) or higher, the air conditioner will automatically dehumidify the air to reduce fogging. Operating tips • In humid weather, select before driving. This will prevent your windshield from fogging.
Controls and features USING YOUR AUDIO SYSTEM AM/FM Stereo/Cassette/Premium Sound FM 1 ST DOLBY SYSTEM POWER AUDIO AM/FM 1 2 3 – VOLUME + 4 5 CLOCK Power control Press the control to turn the audio system on or off. SCAN AMS SEEK POWER Volume control Press the control to – + VOLUME raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on.
Controls and features station by using the Automatic Music Search (AMS) button. • Press the AMS control until the display shows TUNE. • Press and release SEEK either or on the SEEK control to change to the next frequency up or down. • Press and hold down or to quickly move through the frequencies. Seek function The seek function control works in radio or tape mode. Seek function in radio mode • Press to find the SEEK next listenable station down the frequency band.
Controls and features In order to ensure proper operation of the AMS feature, the tape MUST have a blank section of at least 4 seconds duration between programs. Scan function The scan function works in radio mode. SCAN • Press the SCAN button to activate the scan mode. The radio scans up the frequency band, stopping on each listenable station for approximately a five-second sampling. • Press the SCAN button a second time to deactivate the feature.
Controls and features Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output. • Push the AUDIO control repeatedly AUDIO until the display reads BASS. • Press (+) or (−) on – + VOLUME the volume control to increase or decrease bass output. Treble adjust The treble adjust control allows you to increase or decrease the audio system’s treble output. • Push the AUDIO control repeatedly AUDIO until the display reads TREB.
Controls and features Speaker fade adjust Speaker sound distribution can be adjusted between the front and rear speakers. • Push the AUDIO control repeatedly AUDIO until the display reads FADE. • Press the (+) side of – + VOLUME the volume control to shift sound to the front speakers. • Press the (−) side of the volume control to shift sound to the rear speakers. Tape play select Insert a tape to begin tape play. Push only slightly when inserting a cassette tape (with the open edge to the right).
Controls and features Tape eject Press the control to stop and eject a tape. Dolby T noise reduction Dolbyt noise reduction manufactured under license from Dolby Laboratories Licensing Corporation operates only in tape mode. Dolbyt reduces the amount of hiss and static during tape playback. Press the button to activate (and deactivate) Dolbyt noise reduction. Setting the clock Press the CLOCK control while simultaneously depressing the SEEK control. • Press to set the hours. to set the • Press minutes.
Controls and features AM/FM Stereo/Cassette/MACH 460 Sound SystemT with Premium AM/FM Stereo Cassette FM1 REW AUTOMATIC DNR CrO2 ST FF PLAY EJCT PROG POWER AUDIO VOLUME AM/FM 1 2 3 4 5 CLOCK Power control Press the control to turn the audio system on or off. AUTO PRESET SCAN TUNE SEEK POWER Volume control Press the control to VOLUME raise or lower volume.
Controls and features Tune adjust Tune adjust works in SCAN radio mode and allows TUNE you to manually tune in a particular radio station. • Press the SCAN/TUNE button twice. • The display reads TUNE. Press the SEEK control SEEK to move up or down through the frequencies. to move down or to move up the • Press frequency band. • Press and hold down or to quickly move through the frequencies. Seek function The seek function control works in radio or tape mode.
Controls and features • Press tape. to listen to the next selection on the Scan function The scan function works in radio, tape and CD mode (if equipped). Scan function in radio mode This feature allows you SCAN to scan the frequency TUNE band, stopping on each listenable station for approximately a five-second sampling. • Press the SCAN/TUNE button to enter the scan mode. • This display reads SCN. Use the SEEK button SEEK to scan up or down the frequency band.
Controls and features • Press to scan forward selections. Press the SCAN/TUNE button again to stop the scan mode on the current selection. Radio station memory preset The radio is equipped with five station memory preset controls. These controls can be used to select up to five preset AM stations and ten FM stations (five in FM1 and five in FM2). Setting memory preset stations 1. Select the frequency AM/FM band with the AM/FM select control. 2. Select a station.
Controls and features • Push the AUDIO control repeatedly until the display reads TREB. • Press (+) or (−) on the volume control to increase or decrease treble output. AUDIO VOLUME Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. • Push the AUDIO AUDIO control repeatedly until the display reads BAL. • Press the (+) side of VOLUME the volume control to shift sound to the right speakers.
Controls and features Push only slightly when inserting a cassette tape (with the open edge to the right). A cassette deck loading mechanism pulls the tape in the rest of the way. Press PLAY to begin PLAY cassette tape play. PROG Rewind/fast forward function in tape mode Press the control to rewind the tape. REW Play will continue once the beginning of the tape is reached or rewind is stopped. Press the control to fast forward the tape.
Controls and features Setting the clock Press the CLOCK control while simultaneously depressing the SEEK control. • Press to set the hours. • Press to set the minutes. CLOCK SEEK Premium AM/FM Stereo Single CD Radio/Premium Sound or MACH 460 Sound SystemT with Single CD Radio POWER DISC EJECT COMP AM/FM REV FF AUDIO AUTO PLAY SCAN + VOL – AUTOMATIC DNR PRESET 1 2 Power control Press the control to turn the audio system on or off.
Controls and features AM/FM select The AM/FM select AM/FM control works in radio mode and allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations. Tune adjust The tune control works in radio mode. Tune adjust in radio mode • Press the SCAN/ TUNE control twice. • Within approximately five seconds, press and release either or on the SEEK button to change to the next frequency up or down. • Press and hold down or through the frequencies.
Controls and features Scan function The scan function works in radio mode. SCAN TUNE Scan function with compact disc radio • Press the SCAN/ SCAN TUNE control once. TUNE on the • Push SEEK control to hear a brief sampling of listenable stations SEEK up the frequency band. to hear a • Push brief sampling of listenable stations down the frequency band. Setting memory preset stations 1. Select the frequency AM/FM band with the AM/FM select control. 2. Select a station.
Controls and features set preset stations. This feature is helpful on trips when you travel between cities with different radio stations. Starting automatic memory store 1. Select a frequency AM/FM using the AM/FM select control. 2. Press the AUTO PRESET control. AUTO PRESET 3. When the first six strong stations are filled, the station stored in memory preset control 1 will start playing.
Controls and features Speaker fade adjust Speaker sound distribution can be adjusted between the front and rear speakers. • Push the AUDIO control repeatedly AUDIO until the display reads FADE. • Press the (+) side of + the volume control to shift sound to the VOL front speakers. – • Press the (−) side of the volume control to shift sound to the rear speakers. Reverse/fast forward in CD mode • Press the control for REV less than three seconds for slow reverse.
Controls and features Compression feature Compression adjust brings soft and loud CD passages together for a more consistent listening level. Press the COMP control to activate and deactivate compression adjust. The effect of the feature varies with the music content. Setting the clock Press the CLOCK control while simultaneously depressing the SEEK control. to set the • Press hours. • Press to set the minutes.
Controls and features Play function The system enters the PLAY/STOP PLAY mode when a CD is loaded, label side up, into the disc opening. The PLAY indicator will illuminate. The CD automatically loads into the unit and begins play at the beginning of the first track. When the CD reaches the end, the disc player automatically returns to the beginning of the CD and resumes play. Stop function Press the PLAY/STOP PLAY/STOP control to temporarily stop CD play.
Controls and features If you hold down the fast forward control until the end of the CD is reached, the display will show the end time of the last track and the sound will be muted. When the fast forward control is released, the player will resume play at the beginning of the first track. AMS control The AMS (Automatic AMS Music Search) control on your CD player allows you to quickly find a particular selection on the disc.
Controls and features Troubleshooting the CD player (if equipped) The laser beam used in the compact disc player is harmful to the eyes. Do not attempt to disassemble the case. If sound skips: • You may be traveling on a rough road, playing badly scratched discs or the disc may be dirty. Skipping will not scratch the discs or damage the player. If your changer does not work, it may be that: • A disc is already loaded where you want to insert a disc. • The disc is inserted with the label surface downward.
Controls and features Cleaning cassette player (if equipped) Clean the tape player head with a cassette cleaning cartridge after ten to twelve hours of play in order to maintain the best sound and operation. Cassette and cassette player care • Use only cassettes that are 90 minutes long or less. • Do not expose tapes to direct sunlight, high humidity, extreme heat or extreme cold. Allow tapes that may have been exposed to extreme temperatures to reach a moderate temperature before playing.
Controls and features • Terrain. Hills, mountains and tall buildings between your vehicle’s antenna and the radio station signal can cause FM reception problems. Static can be caused on AM stations by power lines, electric fences, traffic lights and thunderstorms. Moving away from an interfering structure (out of its “shadow”) returns your reception to normal. • Station overload. Weak signals are sometimes captured by stronger signals when you pass a broadcast tower.
Controls and features The bars of varying length are for intermittent wipers. When in this position rotate the control upward for fast intervals and downward for slow intervals. Push the control on the end of the stalk to activate washer. Push and hold for a longer wash cycle. The washer will automatically shut off after ten seconds of continuous use. HI LO OFF Mist Function To operate the Mist function of the windshield wipers, push and release the windshield washer control quickly.
Controls and features POSITIONS OF THE IGNITION 1. ACCESSORY, allows 3 2 the electrical accessories such as the radio to operate while the engine is not 1 running. 2. LOCK, locks the steering wheel, automatic transmission gearshift lever and allows key removal. 3. OFF, shuts off the engine and all accessories without locking the steering wheel. 4. ON, all electrical circuits operational. Warning lights illuminated. Key position when driving. 5. START, cranks the engine.
Controls and features SPEED CONTROL To turn speed control on • Press ON. Vehicle speed cannot be controlled until the vehicle is traveling at or above 48 km/h (30 mph). ON OFF Do not use the speed control in heavy traffic or on roads that are winding, slippery, or unpaved. Do not shift the gearshift lever into N (Neutral) with the speed control on. To turn speed control off • Press OFF or • Turn off the vehicle ignition.
Controls and features If you drive up or down a steep hill, your vehicle speed may vary momentarily slower or faster than the set speed. This is normal. Speed control cannot reduce the vehicle speed if it increases above the set speed on a downhill. If your vehicle speed is faster than the set speed while driving on a downhill, you may want to shift to the next lower gear or apply the brakes to reduce your vehicle speed.
Controls and features To set a lower set speed • Press and hold CST/ COAST. Release the RSM control when the SET desired speed is ACC reached or COAST • Press and release CST/COAST. Each press will decrease the set speed by 1.6 km/h (1 mph) or • Depress the brake pedal. When the RSM desired vehicle SET speed is reached, ACC press SET/SET ACC/ COAST SET ACCEL.
Controls and features Pressing OFF will erase the previously programmed set speed. ON OFF To return to a previously set speed • Press RES/RSM/ RESUME. For RES/ RSM RSM/RESUME to SET operate, the vehicle ACC speed must be faster COAST than 48 km/h (30 mph). INTERIOR LAMPS Map lamps (if equipped) If equipped with a convertible top the map lamps and controls are located on the rearview mirror. Press the controls on either side of each map lamp to activate the lamps.
Controls and features POWER WINDOWS (IF EQUIPPED) Press and hold the rocker switches to open and close windows. • Press the top portion of the rocker switch to close. • Press the bottom portion of the rocker switch to open. Express down To make the driver window open fully without holding the window control, press the driver window control completely down and release quickly. Depress again to stop window operation. Window lock The window lock feature allows only the driver to operate the power windows.
Controls and features POWER DOOR LOCKS Press U to unlock all doors and L to lock all doors. U L POWER SIDE VIEW MIRRORS (IF EQUIPPED) To adjust your mirrors: 1. Select to adjust the left mirror or to adjust the right mirror. 2. Move the control in the direction you wish to tilt the mirror. 3. Return to the center position to lock mirrors in place.
Controls and features CENTER CONSOLE Your vehicle may be equipped with a variety of console features. These include: • dual cupholders • auxiliary power point • coin holder slots (if equipped) • foglamp control (if equipped) • convertible top control (if equipped) Use only soft cups in the cupholder. Hard objects can injure you in a collision. Foglamp control (if equipped) Turn on the parking lamps or the low-beam headlamps.
Controls and features Convertible (If equipped) Do not store articles behind rear seat. Articles stored in the convertible top stowage compartment may break the rear glass window when the top is lowered. Lowering the convertible top The convertible top can be lowered with the side windows either up or down. The convertible top will not operate unless the parking brake is engaged. Do not lower the top while the vehicle is moving because the top may be severely damaged.
Installation of the boot 1. Insert boot tongue into groove located on rear seat. 2. Push boot forward until rear attachment engages under molding. 3. Push forward flap of boot until both clips engage under trim panel edge. Repeat on other side of vehicle. 54 T PARK BRAK E 6. Push the convertible top switch on the console in front of the armrest and hold until the top is completely stored. 7. Disengage the parking brake.
Controls and features 4. Tuck side attachments under molding. Repeat on other side of vehicle. 5. Push and pull front of boot to ensure tongue is engaged into groove. 6. Removal Raising the convertible top The convertible top will not operate unless the parking brake is engaged. Do not raise the top while the vehicle is moving because the top may be severely damaged. To raise the convertible top: 1. Bring the vehicle to a complete stop. Engage the parking brake. Key must be in the ON position. 2.
Controls and features 5. Open both top clamps before the top meets the windshield header 6. Continue to use the top motor to raise the top until it has reached the fully closed position flush to the header. 7. The two pins under the forward edge of the top should seat themselves in the matching holes in the header. 8. To fasten both clamps securely, push the clamp handles into the header on the top until they are flush with the header.
Controls and features Locking the doors Press this control to lock all doors. To confirm all doors are closed and locked, press the control a second time within three seconds. The doors will lock again, the horn will chirp and the lamps will flash. If any of the doors are ajar, the horn will make two quick chirps and the chime may sound, reminding you to properly close all doors. Opening the trunk Press the control once to open the trunk.
Controls and features Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Illuminated entry The interior lamps illuminate when the remote entry system is used to unlock the door(s) or sound the personal alarm. The system automatically turns off after 25 seconds or when the ignition is turned to the START/RUN or ACC position.
Controls and features After doors lock/unlock, press any control on all transmitters (up to four). With each control press of the transmitters, the door should cycle (lock/unlock) to confirm programming. When completed, turn the ignition to OFF. The door locks should cycle (lock/unlock) one last time to confirm completion of programming. All transmitters must be programmed at the same time. Replacing the batteries The transmitter is powered by two coin type three-volt lithium batteries.
Controls and features SECURILOCKY PASSIVE ANTI-THEFT SYSTEM The SecuriLocky passive anti-theft system provides an advanced level of vehicle theft protection. Your vehicle’s engine can only be started with the two special SecuriLocky electronically coded keys provided with your vehicle. Each time you start your vehicle, the SecuriLocky key is read by the SecuriLocky passive anti-theft system.
Controls and features Theft indicator The theft indicator on the instrument cluster will operate as follows: • When the ignition is OFF, the theft indicator will flash briefly every 2 seconds to indicate the SecuriLocky system is protecting your vehicle. • When the ignition is turned to RUN or START, the theft indicator will light for 3 seconds and then go out.
Controls and features 1. Insert the first previously programmed SecuriLocky key into the ignition and turn the ignition from OFF to RUN (maintain ignition in RUN for at least one second). 2. Turn ignition to OFF and remove the first SecuriLocky key from the ignition. 3.
Seating and safety restraints SEATING Adjustable head restraints (if equipped) Your vehicle’s seats may be equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible. Refer to the following to raise and lower the head restraints.
Seating and safety restraints Lift handle to move seat forward or backward. Pull lever up to adjust seatback. Adjusting the front power seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop. Always drive and ride with your seatback upright and the lap belt snug and low across the hips.
Seating and safety restraints Press to raise or lower the front portion of the seat cushion. Press to raise or lower the rear portion of the seat cushion. Press the control to move the seat forward, backward, up or down. Rear seat entry/exit Use the seatback release to fold the back of the front seat forward for rear seat passenger entry or exit. This release handle is located on the lower outboard back of the seat. The seatback locks automatically when returned to the normal position.
Seating and safety restraints Using the manual lumbar support (if equipped) The lumbar control is located on the inboard side of the driver’s seatback. Move the control up to increase firmness and down to decrease firmness. 2nd seat/Split-folding rear seat (if equipped) One or both rear seatbacks can be folded down to provide additional cargo space. To lower the seatback(s) from inside the vehicle, pull tab to release seat back and then fold seatback down.
Seating and safety restraints To prevent the risk of injury, make sure children sit where they can be properly restrained. Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision. All occupants of the vehicle, including the driver, should always properly wear their safety belts, even when an air bag SRS is provided. It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle.
Seating and safety restraints Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle. 2. To unfasten, push the release button and remove the tongue from the buckle. The front and rear outboard safety restraints in the vehicle are combination lap and shoulder belts.
Seating and safety restraints When to use the automatic locking mode • When a tight lap/shoulder fit is desired. • Anytime a child safety seat is installed in a passenger front or outboard rear seating position (if equipped). Refer to Safety Restraints for Children or Safety Seats for Children later in this chapter. How to use the automatic locking mode • Buckle the combination lap and shoulder belt. • Grasp the shoulder portion and pull downward until the entire belt is extracted.
Seating and safety restraints Safety belt extension assembly If the safety belt assembly is too short, even when fully extended, 20 cm (8 inches) can be added to the safety belt assembly by adding a safety belt extension assembly (part number 611C22). Safety belt extension assemblies can be obtained from your dealer at no cost. Use only extensions manufactured by the same supplier as the safety belt. Manufacturer identification is located at the end of the webbing on the label.
Seating and safety restraints Safety belt maintenance Inspect the safety belt systems periodically to make sure they work properly and are not damaged. Inspect the safety belts to make sure there are no nicks, wears or cuts, replacing if necessary.
Seating and safety restraints Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. Air bags DO NOT inflate slowly or gently and the risk of injury from a deploying air bag is greatest close to the trim covering the air bag module.
Seating and safety restraints Do not put anything on or over the air bag module. Placing objects on or over the air bag inflation area may cause those objects to be propelled by the air bag into your face and torso causing serious injury. Do not attempt to service, repair, or modify the Air Bag Supplemental Restraint System or its fuses. See your Ford or Lincoln-Mercury dealer. Children and air bags For additional important safety information, read all information on safety restraints in this guide.
Seating and safety restraints How does the air bag supplemental restraint system work? The air bag SRS is designed to activate when the vehicle sustains sufficient longitudinal deceleration sufficient to cause the sensors to close an electrical circuit that initiates air bag inflation. The fact that the air bags did not inflate in a collision does not mean that something is wrong with the system. Rather, it means the forces were not of the type sufficient to cause activation.
Seating and safety restraints there is the risk of death or serious injuries such as fractures, facial and eye injuries or internal injuries, particularly to occupants who are not properly restrained or are otherwise out of position at the time of air bag deployment. Thus, it is extremely important that occupants be properly restrained as far away from the air bag module as possible while maintaining vehicle control. Several air bag system components get hot after inflation.
Seating and safety restraints A difficulty with the system is indicated by one or more of the following: • The readiness light AIR will either flash or BAG stay lit. • The readiness light will not illuminate immediately after ignition is turned on. • A series of five beeps will be heard. The tone pattern will repeat periodically until the problem and light are repaired. If any of these things happen, even intermittently, have the SRS serviced at your dealership or by a qualified technician immediately.
Seating and safety restraints Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision. Always follow the instructions and warnings that come with any infant or child restraint you might use. When possible, place children in the rear seat of your vehicle. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position.
Seating and safety restraints seats raise the child and provide a shorter, firmer seating cushion that encourages safer seating posture and better fit of lap and shoulder belts on the child. A belt-positioning booster should be used if the shoulder belt rests in front of the child’s face or neck, or if the lap belt does not fit snugly on both thighs, or if the thighs are too short to let the child sit all the way back on the seat cushion when the lower legs hang over the edge of the seat cushion.
Seating and safety restraints When installing a child safety seat: • Review and follow the information presented in the Air Bag Supplemental Restraint System section in this chapter. • Use the correct safety belt buckle for that seating position. • Insert the belt tongue into the proper buckle until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle.
Seating and safety restraints Installing child safety seats in combination lap and shoulder belt seating positions 1. Position the child safety seat in a seat with a combination lap and shoulder belt. An air bag can kill or injure a child in a child seat. If you must use a forward-facing child seat in the front seat, move seat all the way back. Children 12 and under should be properly restrained in the rear seat whenever possible. 2.
Seating and safety restraints 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until you hear a snap and feel the latch engage. Make sure the tongue is latched securely by pulling on it. 5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract.
Seating and safety restraints 10. Try to pull the belt out of the retractor to make sure the retractor is in the automatic locking mode (you should not be able to pull more belt out). If the retractor is not locked, unbuckle the belt and repeat steps two through nine. Check to make sure the child seat is properly secured before each use.
Starting PREPARING TO START YOUR VEHICLE Engine starting is controlled by the ignition system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting. Only use the accelerator when you have difficulty starting the engine. For more information on starting the vehicle, refer to Starting the engine in this chapter.
Starting Important safety precautions A computer system controls the engine’s idle revolutions per minute (RPM). When the engine starts, the idle RPM runs faster to warm the engine. If the engine idle speed does not slow down automatically, have the vehicle checked. Do not allow the vehicle to idle for more than ten minutes at high engine RPM. Before starting the vehicle: 1. Make sure all vehicle occupants have buckled their safety belts.
Starting 3. Turn the key to 4 (ON) without turning the key to 5 (START). 4 3 5 2 1 50 40 C 60 70 80 100 120 2 100 160 40 20 120 MPH 5 SELECT/RESET 7 1 L 6 0 km/h H 0 0 0 0 0 0 .0 FUEL DOOR F L AIR THEFT BAG 60 50 40 C H 30 SERVICE ENGINE SOON LOW FUEL 70 80 90 100 40 220 130 240 20 MPH km/h ABS 4 3 200 10 O/D OFF H BRAKE ! P 5 RPMX1000 120 140 110 100 160 80 180 120 60 20 2 6 0 8 1 7 L H 140 150 SELECT/RESET 0 0 0 0 0 0 .
Starting STARTING THE ENGINE 1. Turn the key to 5 (START) without pressing the accelerator pedal and release as soon as the engine starts. The key will return to 4 (ON). 4 3 5 2 1 2. If the temperature is above –12°C (10°F) and the engine does not start within five seconds on the first try, turn the key to OFF, wait ten seconds and try again. 3. If the temperature is below –12°C (10°F) and the engine does not start in fifteen seconds on the first try, turn the key OFF and wait ten seconds and try again.
Starting Guarding against exhaust fumes Although odorless and colorless, carbon monoxide is present in exhaust fumes. Take precautions to avoid its dangerous effects. If you ever smell exhaust fumes of any kind inside your vehicle, have your dealer inspect and fix your vehicle immediately. Do not drive if you smell exhaust fumes. These fumes are harmful and could kill you. Have the exhaust and body ventilation systems checked whenever: • the vehicle is raised for service.
Driving BRAKES Your service brakes are self-adjusting. Refer to the scheduled maintenance guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the brakes are applied.
Driving The ABS operates by detecting the onset of wheel lockup during brake applications and compensating for this tendency. The wheels are prevented from locking even when the brakes are firmly applied. The accompanying illustration depicts the advantage of an ABS equipped vehicle (on bottom) to a non-ABS equipped vehicle (on top) during hard braking with loss of front braking traction.
Driving stopping distance. Always leave enough room between your vehicle and the vehicle in front of you to stop. • We recommend that you familiarize yourself with this braking technique. However, avoid taking any unnecessary risks. Hydraulic brake booster system (Hydroboost) The Hydroboost system receives fluid pressure from the power steering pump to provide power assist during braking. The sound of the pump operating may be heard by the driver, but this is a normal characteristic of the system.
Driving The parking brake is not recommended to stop a moving vehicle. However, if the normal brakes fail, the parking brake can be used to stop your vehicle in an emergency. Since the parking brake applies only the rear brakes, the vehicle’s stopping distance will increase greatly and the handling of your vehicle will be adversely affected. Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park) (automatic transmission) or in 1 (First) (manual transmission).
Driving the fully electronic spark and fuel injection systems. This process is very sensitive to driving conditions and very fast acting. The rear wheels “search” for optimum traction several times a second and adjustments are made accordingly. The Traction Controly system will allow your vehicle to make better use of available traction on slippery surfaces. The system is a driver aid which makes your vehicle easier to handle primarily on snow, ice covered and gravel roads.
Driving If the power steering system breaks down (or if the engine is turned off), you can steer the vehicle manually, but it takes more effort.
Driving Press lightly on the accelerator in each gear. Do not rock the vehicle for more than a few minutes. The transmission and tires may be damaged or the engine may overheat. Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn off the ignition whenever you leave your vehicle. If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly. See your dealer or a qualified service technician.
Driving P (Park) Always come to a complete stop before shifting into P (Park). Make sure the gearshift is securely latched in P (Park). This position locks the transmission and prevents the rear wheels from turning. Always set the parking brake fully and make sure the gearshift is securely latched in P (Park). Never leave your vehicle unattended while it is running. R (Reverse) With the gearshift in R (Reverse), the vehicle will move backward.
Driving N (Neutral) With the gearshift in N (Neutral), the vehicle can be started and is free to roll. Hold the brake pedal down while in this gear. (Overdrive) The normal driving position for the best fuel economy. Transmission operates in gears one through four. (Overdrive) can be deactivated by pressing the transmission control switch on the end of the gearshift lever. The transmission control O/D indicator light (TCIL) OFF will illuminate on the instrument cluster. Drive – Not shown on the display.
Driving gears one through three. (Drive) provides more engine braking than (Overdrive) and is useful when: • driving with a heavy load • towing a trailer up or down steep hills • additional engine braking is desired. If towing a trailer, refer to Driving while you tow in the Trailer Towing chapter. (Overdrive) mode, press the To return to transmission control switch. The O/D OFF indicator will no longer be illuminated.
Driving MANUAL TRANSMISSION OPERATION (IF EQUIPPED) Using the clutch Vehicles equipped with a manual transmission have a starter interlock that prevents cranking the engine unless the clutch pedal is fully depressed. When starting a vehicle with a manual transmission, you must: 1. Put gearshift in N (Neutral). 1 3 5 2. Hold down brake 2 4 R pedal. 3. Depress clutch pedal. 4. Turn ignition to position 5 (START) to start the engine, let the engine idle for a few seconds, then shift into gear. 5.
Driving Recommended shift speeds Do not downshift into 1 (first) when your vehicle is moving faster then 24 km/h (15 mph). This will damage the clutch. Upshift and downshift according to the following chart: Upshifts when accelerating (recommended for best fuel economy) Shift from: 1-2 18 km/h (11 mph) 2-3 31 km/h (19 mph) 3-4 48 km/h (30 mph) 4-5 64 km/h (40 mph) Parking your vehicle 1. Disengage the clutch, apply brake and shift into N (Neutral). 1 3 5 2 4 R 2. Set parking brake. 3.
Driving 4. Turn the ignition key to position 3 (OFF). 4 3 5 2 1 Do not park your vehicle in Neutral, it may move unexpectedly and injure someone. Use 1 (First) gear and set the parking brake fully. Reverse You can shift into R (Reverse) only by moving the gearshift to the right of 5 (Fifth) gear before you shift into R (Reverse). This is a feature that protects you from accidentally shifting into R (Reverse) when you downshift from 5 (Fifth).
Driving gearshift back into Neutral. Then, release the clutch pedal for a moment and repeat steps 2 through 4. Removing key from ignition • Turn the ignition key to position 3 (OFF). • Push the release lever forward and rotate the key towards you and remove. TRACTION-LOK AXLE (IF EQUIPPED) This axle provides added traction on slippery surfaces, particularly when one wheel is on a poor traction surface. Under normal conditions, the Traction-Lok axle functions like a standard rear axle.
Driving • Payload: Combined maximum allowable weight of cargo, passengers and optional equipment. The payload equals the gross vehicle weight rating minus base curb weight. • GVW (Gross Vehicle Weight): Base curb weight plus payload weight. The GVW is not a limit or a specification. • GVWR (Gross Vehicle Weight Rating): Maximum total weight of the base vehicle, passengers, optional equipment and cargo.
Driving • Trailer Weight Range: Specified weight range that the trailer must fall within that ranges from zero to the maximum trailer weight rating. Remember to figure in the tongue load of your loaded trailer when figuring the total weight. Do not exceed the GVWR or the GAWR specified on the Safety Compliance Certification Label. Do not use replacement tires with lower load carrying capacities than the originals because they may lower the vehicle’s GVWR and GAWR limitations.
Driving limitation could result in serious damage to the vehicle and/or personal injury. TRAILER TOWING Your vehicle is capable of towing a trailer up to 454 kg (1 000 lbs.) gross trailer weight with a maximum tongue load of 45 kg (100 lbs.). Do not tow a trailer until your vehicle has been driven at least 800 km (500 miles). Towing a trailer places an additional load on your vehicle’s engine, transmission, axles, brakes, tires and suspension. Inspect these components carefully after towing.
Driving Trailer brakes Electric brakes and manual, automatic or surge-type brakes are safe if installed properly and adjusted to the manufacturer’s specifications. The trailer brakes must meet local and Federal regulations. Do not connect a trailer’s hydraulic brake system directly to your vehicle’s brake system. Your vehicle may not have enough braking power and your chances of having a collision greatly increase. The braking system of the tow vehicle is rated for operation at the GVWR not GCWR.
Driving Servicing after towing If you tow a trailer for long distances, your vehicle will require more frequent service intervals. Refer to your Scheduled Maintenance guide for more information. Trailer towing tips • Practice turning, stopping and backing up in an area before starting on a trip to get the feel of the vehicle trailer combination. When turning, make wider turns so the trailer wheels will clear curbs and other obstacles. • Allow more distance for stopping with a trailer attached.
Driving Once through the water, always try the brakes. Wet brakes do not stop the vehicle as effectively as dry brakes. Drying can be improved by moving your vehicle slowly while applying light pressure on the brake pedal. Driving through deep water where the transmission is submerged may allow water into the transmission and cause internal transmission damage.
Roadside emergencies HAZARD FLASHER Use only in an emergency to warn traffic of vehicle breakdown, approaching danger, etc. The hazard flashers can be operated when the ignition is off. • The hazard lights control is located on top of the steering column. • Depress hazard lights control to activate all hazard flashers simultaneously. • Depress control again to turn the flashers off.
Roadside emergencies The fuel pump shut-off switch is located on the left side of the trunk behind the trunk liner. FUSES AND RELAYS Fuses If electrical components in the vehicle are not 15 working, a fuse may have blown. Blown fuses are identified by a broken wire within the fuse. Check the appropriate fuses before replacing any electrical components. Always replace a fuse with one that has the specified amperage rating.
Roadside emergencies Standard fuse amperage rating and color COLOR CarFuse tridge Link Maxi CarFuses tridge Grey Grey — — — Violet Violet — — — Pink Pink — — — Tan Tan — — — Brown Brown — — — Red Red — — — Blue Blue — — — Yellow Yellow Yellow Blue Blue Natural Natural — — — Green Green Green Pink Pink — — Orange Green Orange — — Red Red Red — — Blue — Yellow — — Tan — Brown — — Natural — Black Fuse Mini Rating Fuses 2A 3A 4A 5A 7.
1 2 3 4 5 7 8 9 10 11 OWNERS MANUAL FOR FUSE INFO 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 44 43 6 SEE 42 Roadside emergencies The fuses are coded as follows: Fuse/Relay Fuse Amp Location Rating 1 20A 2 20A 3 — 4 10A 5 15A 6 7 8 9 10 20A 15A 20A — 10A 11 12 13 14 15A — 15A — Description Cigar Lighter Engine Controls Not Used RH Low Beam Headlamp Instrument Cluster, Traction Control Switch Starter Motor
Roadside emergencies Fuse/Relay Fuse Amp Description Location Rating 15 15A Power Lumbar 16 — Not Used 17 15A Speed Control Servo, Shift Lock Actuator 18 15A Electronic Flasher 19 15A Power Mirror Switch, GEM, Anti-Theft Relay, Power Door Locks, Door Ajar Switches 20 15A Convertible Top Switch 21 5A Instrument Cluster and Engine Control Memory 22 — Not Used 23 15A A/C Clutch, Defogger Switch 24 30A Climate Control Blower Motor 25 25A Luggage Compartment Lid Release 26 30A Wiper/Washer Motor, Wiper Relays 27
Roadside emergencies Fuse/Relay Fuse Amp Description Location Rating 34 20A Instrument Cluster, CCRM, Data Link Connector, Securilock Transciever Module 35 15A Shift Lock Actuator, PCM, Speed Control Servo, ABS Module 36 15A Airbag Control Module 37 10A Adjustable Illumination 38 20A Highbeams 39 5A GEM 40 — Not Used 41 15A Brake Lamp 42 — Not Used 43 20A CB Power Windows 44 — Not Used Power distribution box The power distribution box is located in the engine compartment.
Roadside emergencies 14 MINI 13 MINI 15 16 MINI MINI 17 18 MINI MINI 21 22 MINI MINI 19 20 MINI MINI 25 MAXI 23 24 MINI MINI 26 MAXI 27 MAXI 28 CB 12 MAXI 11 MAXI 10 MAXI 9 MAXI 8 MAXI 7 MAXI 6 MAXI 5 MAXI 4 MAXI 3 MAXI 2 MAXI 1 MAXI 29 DIODE Always replace the cover to the Power Distribution Box before reconnecting the battery or refilling fluid reservoirs. 1 RELAY 2 RELAY 3 RELAY 4 RELAY CONSULTER LA GUIDE 5 RELAY SEE OWNERS MANUAL The high-current fuses are coded as follows.
Roadside emergencies Fuse/Relay Fuse Amp Description Location Rating 7 30A** Secondary Air Injection (3.8L only) 8 50A** ABS Module 9 20A** Auxiliary Power Point 10 30A** Parklamps 11 30A** Rear Window Defrost Control 12 40A** Power Windows, Power Locks 13 — Not Used 14 20A* Fuel Pump 15 10A* Radio 16 20A* Horn 17 20A* Anti-Lock Brake System 18 25A* Power Seats 19 — Not Used 20 20A* Generator 21 — Not Used 22 — Not Used 23 — Not Used A/C Pressure (3.
Roadside emergencies Temporary spare tire information Your vehicle may have a temporary spare tire. The temporary spare tire for your vehicle is labeled as such. It is smaller than a regular tire and is designed for emergency use only. Replace this tire with a full-size tire as soon as possible. If you use the temporary spare tire continuously or do not follow these precautions, the tire could fail, causing you to lose control of the vehicle, possibly injuring yourself or others.
Roadside emergencies 1. Park on a level surface, activate hazard flashers and set parking brake. 2. Place gearshift lever in P (Park) or R (manual transmission), turn engine OFF, and block the diagonally opposite wheel. 3. Remove the spare tire, jack and lug wrench. 4. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. 5. Put the jack in the jack notch next to the tire you are changing.
Roadside emergencies Never use the rear differential as a jacking point. To lessen the risk of personal injury, do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire. 6. Remove the lug nuts with the lug wrench. 7. Replace the flat tire with the spare tire, making sure the valve stem is facing outward. Reinstall lug nuts until the wheel is snug against the hub.
Roadside emergencies 12. If using a mini-spare tire, turn off the traction control switch. Anti-theft lug nuts (if equipped) If your vehicle is equipped with this feature, one of the lug nuts on each wheel must be removed and replaced with a special key. The key and registration card are attached to the lug wrench and stored with the spare tire. If you lose the key, send the registration card to the manufacturer (not the dealer) to get a replacement key.
Roadside emergencies JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Do not push start your vehicle. You could damage the catalytic converter. Batteries contain sulfuric acid which can burn skin, eyes, and clothing, if contacted. Do not attempt to push start your vehicle. Automatic transmissions do not have push-start capability. Preparing your vehicle 1.
Roadside emergencies Connecting the jumper cables + + – – 1. Connect the positive (+) booster cable to the positive (+) terminal of the discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. + + – – 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery. + + – – 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery.
Roadside emergencies + + – – 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor. The preferred locations of an exposed metal part (to ground the circuit) are the alternator mounting brackets or an engine lifting eye. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped.
Roadside emergencies Removing the jumper cables + – – + Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. + + – – 2. Remove the jumper cable on the negative (-) connection of the booster vehicle’s battery. + + – – 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery.
Roadside emergencies + + – – 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions. WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or, if you are a member, your roadside assistance center.
Roadside emergencies It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. However, on Mustang and Mustang GT models, a slingbelt with T-hooks can also be used. Do not tow Cobra or Convertible models with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure for these vehicles. If your vehicle is to be towed from the rear using wheel lift equipment or a slingbelt, the front wheels must be placed on a dolly to prevent damage to the front fascia (bumper).
Maintenance and care SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easy location. • We provide a Scheduled Maintenance Guide which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide necessary parts and service. Check your “Warranty Guide” to find out which parts and services are covered.
Maintenance and care Working with the engine off • Automatic transmission: 1. Set the parking brake and ensure the gearshift is securely latched in P (Park). 2. Turn off the engine and remove the key. 3. Block the wheels to prevent the vehicle from moving unexpectedly. • Manual transmission: 1. Set the parking brake. 2. Depress the clutch and place the gearshift in 1 (First). 3. Turn off the engine and remove the key. 4. Block the wheels to prevent the vehicle from moving unexpectedly.
Maintenance and care OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom left corner of the instrument panel. HOOD 2. Go to the front of the vehicle and release the auxiliary latch that is located under the front center of the hood. 3. Lift the hood and secure it with the prop rod.
Maintenance and care IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 3.8L OHV V6 engine 10 1 2 3 4 5 9 8 7 6 1. Engine oil filler cap 2. Engine oil dipstick 3. Brake fluid reservoir 4. Power distribution box 5. Windshield washer fluid reservoir 6. Battery 7. Power steering fluid reservoir 8. Engine coolant reservoir 9. Air filter assembly 10.
Maintenance and care 4.6L SOHC V8 engine 10 1 2 3 4 9 8 7 6 5 1. Engine oil dipstick 2. Brake fluid reservoir 3. Power distribution box 4. Windshield washer fluid reservoir 5. Battery 6. Engine coolant reservoir 7. Power steering fluid reservoir 8. Engine oil filler cap 9. Air filter assembly 10. Automatic transmission fluid dipstick (if equipped) ENGINE OIL Checking the engine oil Refer to the Scheduled Maintenance Guide for the appropriate intervals for checking the engine oil. 1.
Maintenance and care 2. Turn the engine off and wait a few minutes for the oil to drain into the oil pan. 3. Set the parking brake and ensure the gearshift is securely latched in P (Park) (automatic transmissions) or 1 (First) (manual transmissions). 4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove the engine oil level indicator (dipstick). • 3.8L OHV V6 engine MIN MAX • 4.6L SOHC V8 engine MIN MAX 6. Wipe the indicator clean.
Maintenance and care • If the oil level is below the MIN mark, add enough oil to raise the level within the MIN—MAX range. • Oil levels above the MAX mark may cause engine damage. Some oil must be removed from the engine by a service technician. 7. Put the indicator back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2.
Maintenance and care Engine oil and filter recommendations Look for this certification mark. Ford oil specification is WSS-M2C153-G. Use SAE 5W-30 motor oil certified for gasoline engines by the American Petroleum Institute. Do not use supplemental engine oil additives, oil treatments or engine treatments. They are unnecessary and could, under certain conditions, lead to engine damage which is not covered by your warranty.
Maintenance and care • 3.8L OHV V6 engine • 4.6L SOHC V8 engine 1. Clean the reservoir cap before removal to prevent dirt or water from entering the reservoir. 2. Visually inspect the fluid level. 3. If necessary, add brake fluid until the level reaches MAX. Do not fill above this line. 4. Use only a DOT 3 brake fluid certified to meet Ford specifications. Refer to Lubricant specifications in the Capacities and specifications chapter. MAX Brake fluid is toxic.
Maintenance and care If you use a brake fluid that is not DOT 3, you will cause permanent damage to your brakes. Do not let the reservoir for the master cylinder run dry. This may cause the brakes to fail. CLUTCH ADJUSTMENT (IF EQUIPPED) Check the clutch adjustment. Refer to the Scheduled Maintenance Guide for the service interval schedules. The clutch on your vehicle is operated by a cable. As necessary, adjust the clutch as described below. 1. Turn the engine off and shift into 1 (First). 2.
Maintenance and care WINDSHIELD WASHER FLUID Checking and adding washer fluid Check the washer fluid whenever you stop for fuel. The reservoir is highlighted with a symbol. If the level is low, add enough fluid to fill the reservoir. In very cold weather, do not fill the reservoir all the way. Do not put engine coolant in the container for the windshield washer fluid.
Maintenance and care ENGINE COOLANT • 3.8L OHV V6 engine • 4.6L V8 engine Check the level of the engine coolant in the reservoir. Refer to the Scheduled Maintenance Guide for service interval schedules. Be sure to read and understand Precautions when servicing your vehicle in this chapter. If the engine coolant has not been checked at the recommended interval, the engine coolant reservoir may become empty. If this occurs, add engine coolant to the coolant reservoir.
Maintenance and care Adding engine coolant Do not put engine coolant in the container for the windshield washer fluid. Do not mix conventional green coolant, orange coolant or recycled coolants together in your vehicle. Use only the type of coolant that your vehicle was originally equipped with. If you are unsure which type of coolant your vehicle requires, contact your local dealer. If sprayed on the windshield, engine coolant could make it difficult to see through the windshield.
Maintenance and care Change your engine coolant according to the appropriate schedule listed in the Scheduled Maintenance Guide. Before adding engine coolant, check the color of the coolant in your vehicle. For vehicles with green coolant, use Ford Premium Cooling System Fluid E2FZ-19549–AA (in Canada, Motorcraft CXC-8–B) or an equivalent premium engine coolant that meets Ford specification ESE-M97B44–A.
Maintenance and care For vehicles with orange coolant, no recycling process has been approved at this time and use of such coolant may harm engine and cooling system components. Always dispose of used automotive fluids in a responsible manner. Follow your community’s regulations and standards for recycling and disposing of automotive fluids. Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, refer to Refill capacities in the Capacities and specifications chapter.
Maintenance and care FILL HOT If your vehicle is equipped with the 3.8L V6 engine, check the power steering fluid level with the engine at normal operating temperature. 1. Start the engine and let it run until it reaches normal operating temperature (the engine coolant temperature gauge indicator will be near the center of the normal area between H and C). 2. While the engine idles, turn the steering wheel left and right several times. 3. Turn the engine off. 4. Check the fluid level on the dipstick.
Maintenance and care If your vehicle is equipped with a 4.6L V8 engine, check the power steering fluid level with the engine at ambient temperature. Allow at least one-half hour after driving for the power steering fluid to cool. 1. Start the engine and allow the engine to idle. MAX MIN 2. Turn the steering wheel left and right several times. 3. Turn the engine off. 4. Check the fluid level in the reservoir. It should be between the MIN and MAX lines. Do not add fluid if the level is within this range. 5.
Maintenance and care been operated for an extended period at high speeds, in city traffic during hot weather or pulling a trailer, the vehicle should be turned off for about 30 minutes to allow fluid to cool before checking. 1. Drive the vehicle 30 km (20 miles) or until it reaches normal operating temperature. 2. Park the vehicle on a level surface and engage the parking brake. 3.
Maintenance and care could result when the vehicle reaches normal operating temperature. The transmission fluid should be in this range if at normal operating temperature (66°C-77°C [150°F-170°F]). The transmission fluid should be in this range if at ambient temperature (10°C-35°C [50°F-95°F]). High fluid level Fluid levels above the safe range may result in transmission failure. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage.
Maintenance and care An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. Checking and adding manual transmission fluid 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Fluid level should be at bottom of the opening. 4. Add enough fluid through the filler opening so that the fluid level is at the bottom of the opening. 5. Install and tighten the fill plug securely. Use only fluid that meets Ford specifications.
Maintenance and care BATTERY Your vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. However, for severe usage or in high temperature climates, check the battery electrolyte level. Refer to the Scheduled Maintenance Guide for the service interval schedules. Keep the electrolyte level in each cell up to the “level indicator”. Do not overfill the battery cells.
Maintenance and care Batteries normally produce explosive gases which can cause personal injury. Therefore, do not allow flames, sparks or lighted substances to come near the battery. When working near the battery, always shield your face and protect your eyes. Always provide proper ventilation. When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery.
Maintenance and care AD LE RN TU RE 4. The relearning process will automatically complete as you drive the vehicle. • The vehicle may need to be driven 16 km (10 miles) or more to relearn the idle and fuel trim strategy. • If you do not allow the engine to relearn its idle trim, the idle quality of your vehicle may be adversely affected until the idle trim is eventually relearned.
Maintenance and care Changing the wiper blades To replace the wiper blades: 1. Pull the wiper arm away from the windshield and lock into the service position. 2. Turn the blade at an angle from the wiper arm. Push the lock pin manually to release the blade and pull the wiper blade down toward the windshield to remove it from the arm. 3. Attach the new wiper to the wiper arm and press it into place until a click is heard.
Maintenance and care about tire grades exactly as the government has written it. Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1/2) times as well on the government course as a tire graded 100.
Maintenance and care Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law. The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.
Maintenance and care • 15 or 16 inch four tire rotation • 17 inch four tire rotation Replacing the tires Replace the tires when the wear band is visible through the tire treads. Failure to follow these precautions may adversely affect the handling of the vehicle and make it easier for the driver to lose control and roll over.
Maintenance and care Tires that are larger or smaller than your vehicle’s original tires may also affect the accuracy of your speedometer. SNOW TIRES AND CHAINS Driving too fast for conditions creates the possibility of loss of vehicle control. Driving at very high speeds for extended periods of time may result in damage to vehicle components. Snow tires must be the same size and grade as the tires you currently have on your vehicle.
Maintenance and care • The suspension insulation and bumpers will help prevent vehicle damage. Do not remove these components from your vehicle when using snow tires and chains. WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire. If you do not use the proper fuel cap, the pressure in the fuel tank can damage the fuel system or cause it to work improperly in a collision.
Maintenance and care • Automotive fuels can be harmful or fatal if swallowed. Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injury. If fuel is swallowed, call a physician immediately, even if no symptoms are immediately apparent. The toxic effects of fuel may not be visible for hours. • Avoid inhaling fuel vapors. Inhaling too much fuel vapor of any kind can lead to eye and respiratory tract irritation.
Maintenance and care 2. Carefully turn the filler cap counterclockwise 1/8 of a turn until it stops. 3. Pull to remove the cap from the fuel filler pipe. 4. To install the cap, align the tabs on the cap with the notches on the filler pipe. 5. Turn the filler cap clockwise 1/8 of a turn until it stops. If the “Service Engine Soon/Check Engine” indicator comes on and stays on when you start the engine, the fuel filler cap may not be properly installed.
Maintenance and care Emissions Control Information label) are designed to operate on California cleaner-burning, low-sulfur gasolines. If you have a California-certified vehicle and California cleaner-burning gasoline is not available when you refuel, your engine should perform adequately. However, the performance of the emission control devices and systems may be adversely affected.
Maintenance and care “Premium” unleaded gasoline is not recommended (particularly in the United States) because it may cause these problems to become more pronounced. If the problems persist, see your dealer or a qualified service technician. The American Automobile Manufacturers Association (AAMA) issued a fuel specification to provide information on high quality fuels that optimize the performance of your vehicle. We recommend the use of fuels that meet the AAMA specification if they are available.
Maintenance and care If you replace the fuel filter, replace it with an authorized Motorcraft part. The customer warranty may be void for any damage to the fuel system if an authorized Motorcraft fuel filter is not used. ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Your best source of information about actual fuel economy is you, the driver. You must gather information as accurately and consistently as possible.
Maintenance and care Filling the tank For consistent results: • Use the same filling rate setting (low — medium — high) each time the tank is filled. • Allow three automatic click-offs when filling. • Always use the recommended octane rating of a known quality gasoline, preferably a national brand. • Use the same side of the same pump and have the vehicle facing the same direction each time you fill up. • Have the vehicle loading and distribution the same every time.
Maintenance and care Driving style — good driving and fuel economy habits Give consideration to the lists that follow and you may be able to change a number of variables and improve your fuel economy. Habits • Smooth, moderate operation can yield up to 10% savings in fuel. • Steady speeds without stopping will usually give the best fuel economy. • Idling for long periods of time (greater than one minute) may waste fuel. • Anticipate stopping; slowing down may eliminate the need to stop.
Maintenance and care • Combine errands and minimize stop-and-go driving. Maintenance • Keep tires properly inflated and use only recommended size. • Operating a vehicle with the wheels out of alignment will reduce fuel economy. • Use recommended engine oil. Refer to Lubricant Specifications. • Perform all regularly scheduled maintenance items. Follow the recommended maintenance schedule and owner maintenance checks found in your vehicle Scheduled Maintenance Guide.
Maintenance and care EPA window sticker Every new vehicle should have the EPA window sticker. Contact your dealer if the window sticker is not supplied with your vehicle. The EPA window sticker should be your guide for the fuel economy comparisons with other vehicles. It is important to note the box in the lower left corner of the window sticker. These numbers represent the Range of Km/L (MPG) expected on the vehicle, depending upon the driver’s method of operation and conditions.
Maintenance and care Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire. Illumination of the charging system warning light, “Service Engine Soon” light or the temperature warning light, fluid leaks, strange odors, smoke or loss of oil pressure, could indicate that the emission control system is not working properly.
Maintenance and care If the vehicle’s powertrain system or its battery has just been serviced, the OBD-II system is reset to a “not ready for I/M test” condition. To ready the OBD-II system for I/M testing, a minimum of 30 minutes of city and highway driving is necessary as described below: • First, at least 10 minutes of driving on an expressway or highway. • Next, at least 20 minutes driving in stop-and-go, city-type traffic with at least four idle periods.
Maintenance and care Replacing headlamp bulbs Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated. To remove the headlamp bulb: 1. Make sure headlamp switch is in OFF position, then open the hood. 2. At the back of the headlamp, pull two retainer pins up to release the headlamp assembly. 3.
Maintenance and care To install the new bulb: 1. With the flat side of the new bulb’s plastic base facing upward, insert the glass end of the bulb into the lamp assembly. You may need to turn the bulb left or right to align the grooves in the plastic base with the tabs in the lamp assembly. When the grooves are aligned, push the bulb into the lamp assembly until the plastic base contacts the rear of the lamp assembly. 2.
Maintenance and care 5. Rotate the bulb socket counterclockwise about 1⁄4 turn and remove from lamp assembly. 6. Carefully pull the bulb straight out from the socket and push in the new bulb. 7. To complete installation, follow the removal procedure in reverse order. High-mount brakelamp bulbs 1. Open trunk. 2. Inside trunk, locate access hole under the luggage compartment door. 3. Remove the bulb socket by rotating it 45 degrees and pulling it out of the lamp assembly. 4.
Maintenance and care 1. Rotate the foglamp bulb counterclockwise and remove from foglamp (the rear side of the foglamp is shown). 2. Disconnect the electrical connector from the foglamp bulb. 3. Connect the electrical connector to the new foglamp bulb. 4. Install the foglamp bulb in foglamp by rotating clockwise. Replacing license plate lamp bulbs To change the license plate bulbs: 1. Open trunk and remove bulb socket from the trunk lid by turning counterclockwise. 2.
Maintenance and care Map lamps For bulb replacement, see a qualified service technician or your dealer.
Maintenance and care Vertical aim adjustment 1. Park the vehicle on a level surface approximately 7.6 meters (25 feet) from a vertical wall or screen directly in front of it. 2. Measure the height from the center of your headlamp to the ground and mark an 2.4 meters (8 foot) horizontal reference line on the vertical wall or screen at this height (a piece of masking tape works well). The center of the lamp is marked by a 3.0 mm circle on the headlamp lens. 3.
Maintenance and care Washing your vehicle Wash your vehicle regularly with cold or lukewarm water. Never use strong detergents or soap. If your vehicle is particularly dirty, use a quality car wash detergent. Always use a clean sponge, washing glove or similar device and plenty of water for best results. To avoid spots, avoid washing when the hood is still warm, immediately after or during exposure to strong sunlight. During winter months, it is especially important to wash the vehicle on a regular basis.
Maintenance and care windshield as described in Cleaning the wiper blades and windshield. Repairing paint chips Minor scratches or paint damage from road debris may be repaired with touch-up paint, repair foil or aerosol paint spray from the Ford accessory line. Observe the application instructions on the products. Remove particles such as bird droppings, tree sap, insect remains, tar spots, road salt and industrial fallout immediately.
Maintenance and care • Cover the highlighted areas to prevent water damage when cleaning the engine. • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. Cleaning plastic exterior parts Use vinyl cleaner for routine cleaning. Clean with a tar remover if necessary. Do not clean plastic parts with thinners, solvents or petroleum-based cleaners. Cleaning the exterior lamps Wash with the same detergent as the exterior of your vehicle.
Maintenance and care If the wiper still does not wipe properly, this could be caused by substances on the windshield such as tree sap and some hot wax treatments used by commercial car washes. Clean the outside of the windshield with a non-abrasive cleanser such as the non-abrasive Bon-Amit powder. Rinse thoroughly with clean water. Do not use abrasive cleansers on glass as they may cause scratches. The windshield is clean if beads do not form when you rinse it with water.
Maintenance and care Do not use household cleaning products, alcohol solutions, solvents or cleaners intended for rubber, vinyl or plastics. Cleaning and maintaining the safety belts Clean the safety belts with a mild soap solution recommended for cleaning upholstery or carpets. Do not bleach or dye the belts, because these actions may weaken the belt webbing. Check the safety belt system periodically to make sure there are no nicks, wear or cuts.
Capacities and specifications MOTORCRAFT PART NUMBERS Component Air filter Fuel filter Battery Oil filter PCV valve Spark plugs* 3.8L OHV V6 engine FA-1611 FG-800A BXT-59 FL-400S EV-152 AWSF-42EE** 4.6L SOHC V8 engine FA-1634 FG-800A BXT-59 FL-820S EV-98 AWSF-32PP*** * Refer to Vehicle Emissions Control Information (VECI) decal for spark plug gap information. **If a spark plug is removed for inspection, it must be reinstalled in the same cylinder. Cylinders No. 1, 2 and 3 have an “EG” suffix.
Capacities and specifications REFILL CAPACITIES Fluid Ford Part Name Brake fluid High Performance DOT 3 Motor Vehicle Brake Fluid Engine oil Motorcraft (includes 5W30 filter Super change) Premium Motor Oil Engine See coolant1 footnote Power steering fluid Rear axle lubricant2 178 Application All Capacity All 4.7L (5.0 quarts) 3.8L OHV V6 engine 4.6L SOHC V8 engine 3.8L OHV V6 engine Fill to line on reservoir 11.2L (11.8 quarts) 13.3L (14.
Capacities and specifications Fluid Fuel tank Transmission fluid Ford Part Name N/A Application All Motorcraft MERCONtV ATF Automatic with 3.8L OHV V6 engine Automatic with 4.6L SOHC V8 engine Manual with 3.8L OHV V6 engine Manual with 4.6L SOHC V8 engine 3 All Motorcraft MERCONt ATF Windshield washer fluid Ultra-Clear Windshield Washer Concentrate Capacity 58.7L (15.5 gallons) 13.1L (13.9 quarts) 12.0L (12.8 quarts) 2.6L (5.6 pints) 3.1L (6.
Capacities and specifications LUBRICANT SPECIFICATIONS Item Ford part name Brake fluid High Performance DOT 3 Motor Vehicle Brake Fluid Door Silicone weatherLubricant strips Door latch, hood latch, auxiliary hood latch, door hinges, striker plates, seat tracks and fuel filler door hinge Engine coolant Engine oil 180 MultiPurpose Grease Ford Premium Engine Coolant (green in color) Ford Extended Life Engine Coolant (orange in color) Motorcraft 5W30 Super Premium Motor Oil Ford part number C6AZ19542-AB
Capacities and specifications Item Ford part name Lock Penetrating cylinders Lubricant Power Motorcraft steering MERfluid and CONtV convertible ATF top fluid (if equipped) Rear axle Motorcraft lubricant SAE 80W90 Premium Rear Axle Lubricant1 Automatic Motorcraft transmisMERCONtV sion fluid ATF Manual Motorcraft transmisMERCONt sion fluid ATF Disc brake Silicone caliper Brake rails Caliper and Dielectric compound Windshield Ultra-Clear washer Windshield fluid Washer Concentrate Ford part Ford specinumber f
Capacities and specifications ENGINE DATA Engine Cubic inches Horsepower Torque Recommended fuel Firing order Spark plug gap Ignition system Compression ratio 3.8L OHV V6 engine 232 190 @ 5250 rpm 220 lb.-ft. @ 2750 rpm 87 octane 4.6L SOHC V8 engine 281 260 @ 5250 rpm 302 lb.-ft. @ 4000 rpm 87 octane 1-4-2-5-3-6 1.3-1.4 mm (0.05200.056 inch) EDIS 9.4:1 1-3-7-2-6-5-4-8 1.3-1.4 mm (0.05200.056 inch) Coil on plug 9.
Capacities and specifications 3 5 2 4 1 183
Capacities and specifications IDENTIFYING YOUR VEHICLE Safety compliance label The National Highway MFD. BY FORD MOTOR CO. IN U.S.A. DATE: XXXXX GVWR:XXXXX LB/ XXXXX KG Traffic Safety FGAWR: XXXXXX/XXXXXXX RGAWR: XXXXXXX/XXXXXXX THIS VEHICLE CONFORMS TO ALL APPLICABLE FEDERAL Administration MOTOR VEHICLE SAFETY STANDARDS IN EFFECT ON THE DATE OF MANUFACTURE SHOWN ABOVE.
Reporting safety defects REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect that could cause a crash, or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Index Air bag supplemental restraint system ........ 71 and child safety seats ............. 73 description .............. 72 disposal .................... 76 indicator light ......... 75 passenger air bag ... 74 Automatic transmission driving an automatic overdrive .. 94,95,96,97 Axle refill capacities ...... 178 Battery voltage gauge .......... 15 Brakes ................... 88,90 anti-lock .............. 88,89 anti-lock brake system (ABS) warning light ........... 89 fluid, checking and adding ...........
Index Fuel choosing the right fuel ......... 156 comparisons with EPA fuel economy estimates ............... 163 detergent in fuel ... 158 filling your vehicle with fuel ......... 154,155 gauge ....................... 12 quality .................... 157 running out of fuel ............. 158 safety information relating to automotive fuels ....................... 154 Fuses ................. 109,110 Gas mileage (see Fuel economy) ........ 159 160,161,162 Gauges .......................
Index Mirrors side view mirrors (power) ................... 51 Motorcraft parts ...... 158 Octane rating .......... 157 Odometer ................... 14 Panic alarm feature, remote entry system 57 Parking brake ............ 90 Power distribution box (see Fuses) ............. 113 Power door locks ...... 51 Power steering .......... 92 fluid, checking and adding .................... 140 Radio ................ 21,22,23 24,25,26,27,28,29,30 31,32,33,34,35,36,37 38,39,40,41,42,43 Relays ......................
Index fluid, checking and adding (manual) ... 145 manual operation .... 98 Trip odometer ........... 15 Trunk ......................... 57 Vehicle dimensions . 182 Vehicle Identification Number (VIN) ......... 184 Vehicle loading ........ 101 104,105,106 Ventilating your vehicle ............... 87 Warning chimes ........... 6 Washer fluid ............ 136 reservoir ................ 136 Water, Driving through ....... 106 Wheels anti-theft lug nuts ................. 119 Windows ....................
Filling station information Item Recommended fuel Fuel tank capacity Engine oil capacity (includes filter change) Tire size and pressure Hood release Coolant capacity-3.8L OHV V6 engine1 Coolant capacity-4.6L SOHC V8 engine1 Power steering fluid capacity Manual transmission fluid capacity-3.8L OHV V6 engine Manual transmission fluid capacity-4.6L SOHC V8 engine2 Automatic transmission fluid capacity-3.8L OHV V6 engine3 Automatic transmission fluid capacity-4.
Filling station information 1 If your engine coolant is green in color, use Ford Premium Cooling System Fluid. If your engine coolant is orange in color, use Ford Extended Life Engine Coolant. Refer to Adding engine coolant, in the Maintenance and Care chapter. 2 Service refill capacity is determined by filling the transmission to the bottom of the filler hole with the vehicle on a level surface. 3 Ensure correct automatic transmission fluid is used for a specific application.