Contents Before driving Introduction 2 Instrumentation 4 Controls and features Seating and safety restraints 19 113 Starting and driving Starting 139 Driving 144 Roadside emergencies 175 Servicing Maintenance and care 195 Capacities and specifications 243 Customer assistance 252 Reporting safety defects 264 Index 265 All rights reserved.
Introduction ICONS Indicates a safety alert. Read the following section on Warnings. Indicates vehicle information related to recycling and other environmental concerns will follow. Correct vehicle usage and the authorized disposal of waste cleaning and lubrication materials are significant steps towards protecting the environment. Indicates a message regarding child safety restraints. Refer to Seating and safety restraints for more information.
Introduction INFORMATION ABOUT THIS GUIDE The information found in this guide was in effect at the time of printing. Ford may change the contents without notice and without incurring obligation. SPECIAL NOTICES Notice to owners of utility type vehicles Before you drive your vehicle, please read this Owner’s Guide carefully. Your vehicle is not a passenger car. As with other vehicles of this type, failure to operate this vehicle correctly may result in loss of control or an accident.
Instrumentation Instrument cluster (pg. 6) Speed control* (pg. 80) DOOR AJAR CHECK GAGE 4 3 H CHECK ENGINE 5 F ABS 60 70 100 30 20 10 0 40 90 120 140 000000 20 MPH ! E 80 0 0 0 80 60 1 FUEL RESET 50 40 RPMx1000 2 C 6 160 100 180 H SPEED CONT L 110 km/h 120 H L CHECK SUSP O/D OFF RSM OFF ON SET ACC OFF Headlamp control (pg. 19) Instrument panel dimmer switch (pg. 20) * if equipped 4 Tilt steering wheel lever (pg. 85) Turn signal and wiper/washer control (pg.
Instrumentation Electronic sound system (pg. 33) Gearshift (includes overdrive button) (pg. 152) 4WD LOW Rear window/washer control (pg. 86) Rear window defroster control (pg. 30) OD ON/OFF OFF VOL - PUSH ON AM FM CLK BASS TREB BAL FADE CD SEEK SCAN TUNE CD REW CD 2 3 ON PUSH TAPE AMS SIDE 1 - 2 EJ DISCS 1 R. WIPE 4 FF COMP SHUFFLE 5 6 OFF A/C MAX A/C Climate controls (pg. 87) Foglamp Control* (pg.
Instrumentation WARNING LIGHTS AND CHIMES DOOR AJAR CHECK GAGE 4 3 H CHECK ENGINE 5 6 30 20 1 FUEL RESET F E ABS 40 60 70 80 0 0 0 80 100 10 0 ! BRAKE P 40 90 120 60 2 C 50 RPMx1000 140 000000 20 MPH R N D 2 1 160 100 180 H 4WD HIGH km/h 120 THEFT SPEED CONT L 110 H CHECK SUSP 4WD LOW L O/D OFF Check engine Your vehicle is equipped with a computer that monitors the engine’s CHECK emission control system.
Instrumentation 3. The fuel cap may not have been properly installed and securely tightened. These temporary malfunctions can be corrected by filling the fuel tank with good quality fuel and/or properly installing and securely tightening the gas cap. After three driving cycles without these or any other temporary malfunctions present, the Check Engine light should turn off. (A driving cycle consists of a cold engine startup followed by mixed city/highway driving.) No additional vehicle service is required.
Instrumentation Safety belt Momentarily illuminates when the ignition is turned to the ON position to remind you to fasten your safety belts. For more information, refer to the Seating and safety restraints chapter. Brake system warning Momentarily illuminates when the ignition is turned to the ON position ! and the engine is off. If the brake BRAKE warning lamp does not illuminate at this time, seek service immediately. Also illuminates when the parking brake is engaged.
Instrumentation High beams Illuminates when the high beam headlamps are turned on. Anti-theft system (if equipped) Refer to SecuriLocky passive anti-theft system in the Controls and features chapter. THEFT Charging system Illuminates when the ignition is turned to the ON position and the engine is off. The light also illuminates when the battery is not charging properly, requiring electrical system service.
Instrumentation Four wheel drive high (if equipped) This light momentarily illuminates when the ignition is turned to ON. Illuminates when four-wheel drive high is engaged. If the light continues to flash have the system serviced. Door ajar Illuminates when the ignition is in the ON or START position and any door is open. 4WD HIGH DOOR AJAR O/D off (if equipped) Illuminates when the transmission control switch has been pushed. O/D When the light is on, the OFF transmission does not shift into overdrive.
Instrumentation Safety belt warning chime Chimes to remind you to fasten your safety belts. For information on the safety belt warning chime, refer to the Seating and safety restraints chapter. Supplemental restraint system (SRS) warning chime For information on the SRS warning chime, refer to the Seating and safety restraints chapter. Key-in-ignition warning chime Sounds when the key is left in the ignition in the OFF/LOCK or ACC position and the driver’s door is opened.
Instrumentation Speedometer Indicates the current vehicle speed. 50 40 60 70 80 0 0 0 80 100 60 30 20 10 Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the normal area (the area between the “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine immediately and let the engine cool.
Instrumentation Odometer Registers the total kilometers (miles) of the vehicle. 60 70 50 40 80 0 0 0 100 80 90 120 60 30 20 000000 40 40 60 70 80 0 0 0 80 100 10 Tachometer Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine. 90 120 140 000000 40 110 km/h 120 60 30 100 180 MPH 50 20 160 20 10 Trip odometer Registers the kilometers (miles) of individual journeys.
Instrumentation Battery voltage gauge This gauge shows the battery voltage when the ignition is in the ON position. If the pointer moves and stays outside the normal operating range (as indicated), have the vehicle’s electrical system checked as soon as possible. H L Engine oil pressure gauge This shows the engine oil pressure in the system. Sufficient pressure exists as long as the needle remains in the normal range (the area between the “L” and “H”).
Instrumentation MESSAGE CENTER (IF EQUIPPED) With the ignition in the ON position, the message center displays important vehicle information through a constant monitor of vehicle systems. You may select display features on the message center for a display of status preceded by a brief indicator chime. The system will also notify you of potential vehicle problems with a display of system warnings.
Instrumentation For maximum accuracy of this display feature, the ignition should be in the OFF position during fueling. The display FUEL LEVEL ERROR indicates a problem with the fuel indication system. See your dealer or qualified service technician for system maintenance. Fuel status Press once to display the approximate amount of fuel remaining in the fuel tank. Press again to display the approximate amount of fuel used since the system was last reset.
Instrumentation System check Press the system check control to display the status of the following systems: • engine oil life left • engine oil level • voltage level • engine coolant temperature • washer fluid level • fuel level The engine oil life left has two phases. The first display will indicate the oil change status (OK, SOON, REQUIRED). The second display will indicate the percentage of oil life remaining. The display OIL TEMP SIGNAL ERROR indicates a problem with the system.
Instrumentation Oil change reset Press the OIL CHANGE RESET control to reset the oil life feature to 100% (or your personalized oil reset percentage) (at optimal driving conditions, 100% oil life is equivalent to a maximum of 12 000 kilometers [7 500 miles]). After you have the oil changed, you must press and hold the OIL CHANGE RESET control for five seconds. The message center will count down for five seconds. After a successful reset, the message center will display OIL LIFE RESET TO 100%.
Controls and features HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to also turn on the headlamps. OFF Foglamp control (if equipped) Turn on the low-beam headlamps and press the foglamp control to activate the foglamps. The foglamp control will illuminate when the foglamps are on. Press the foglamp control a second time to deactivate the foglamps.
Controls and features Flash to pass Pull toward you to activate and release to deactivate. PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel during headlamp and parklamp operation. • Rotate up to brighten. • Rotate down to dim. • Rotate to full down position to turn off. DIM CLIMATE CONTROL SYSTEM Manual heating and air conditioning system (if equipped) OFF A/C MAX A/C Fan speed control Controls the volume of air circulated in the vehicle.
Controls and features Temperature control knob Controls the temperature of the airflow inside the vehicle. Mode selector control Controls the direction of the airflow to the inside of the vehicle. OFF A/C MAX A/C The air conditioning compressor will operate in all modes except and . However, the air conditioning will only function if the outside temperature is about 10°C (50°F) or above.
Controls and features • (Panel and floor)-Distributes outside air through the instrument panel registers and the floor ducts. Heating and air conditioning capabilities are provided in this mode. For added customer comfort, when the temperature control knob is anywhere in between the full hot and full cold positions, the air distributed through the floor ducts will be slightly warmer than the air sent to the instrument panel registers.
Controls and features • Remove any snow, ice or leaves from the air intake area (at the bottom of the windshield under the hood). • If your vehicle has been parked with the windows closed during hot weather, the air conditioner will do a much faster job of cooling if you drive for two or three minutes with the windows open. This will force most of the hot, stale air out of the vehicle. Then operate your air conditioner as you would normally.
Controls and features Turning the EATC off Press OFF. HI OFF AUTOMATIC FLR • DEF DEF LO Automatic operation Press AUTOMATIC and select the desired temperature. The selected temperature and the word AUTO will appear in the display window. The EATC system will either heat or cool to achieve the selected temperature. The system will automatically determine fan speed, airflow location and if fresh outside air or recirculated air is required.
Controls and features To control the temperature, select any temperature between 18°C (65°F) and 29°C (85°F) by pressing the blue (cooler) or red (warmer) buttons. REAR FAN OFF MAX A/C VENT PNL • FLR For continuous maximum cooling, push the blue button until 16°C (60°F) is shown in the display window. The EATC will continue maximum cooling (disregarding the displayed temperature) until a warmer temperature is selected by pressing the red button.
Controls and features • Rotate the thumbwheel up for higher fan speed or down for lower fan speed. • Press the steering wheel fan speed control up for higher fan speed or down for lower fan speed. The display will show to indicate ˚F manual fan operation. AUTO To return to automatic fan operation, press AUTOMATIC. Manual override controls The override controls are located at the bottom of the EATC and allow you to determine where airflow is directed. To return to full automatic control, press AUTOMATIC.
Controls and features • PNL•FLR-Distributes outside air through the instrument panel registers and the floor ducts. Heating and air conditioning capabilities are provided in this mode. The air will be heated or cooled based on the temperature selection. For added customer comfort, the air distributed through the floor ducts will be slightly warmer than the air sent to the instrument panel registers. • FLOOR-Allows for maximum heating by distributing outside air through the floor ducts.
Controls and features The EATC display window will indicate REAR FAN OFF. The rear console fan will remain off until REAR FAN OFF is pressed again. Operating tips • In humid weather, select DEF before driving. This will prevent your windshield from fogging. After a few minutes, select any desired position. • To prevent humidity buildup inside the vehicle, don’t drive with the climate control system in the OFF position.
Controls and features Rear console climate controls (if equipped) Depending on the equipment package of your vehicle, the rear console may be equipped with rear console audio/climate controls. - VOLUME + MODE SEEK MEMORY The instrument panel climate controls must be on in order for the rear console climate controls to work. Turn the air distribution control to the desired airflow position. Turn the fan speed control to the - VOLUME + MODE desired position.
Controls and features Select for air to flow through these vents: – VOLUME SEEK + BAND MEMORY REAR WINDOW DEFROSTER The rear defroster control is located on the instrument panel. Press the rear defroster control to clear the rear window of thin ice and fog. • The small LED will illuminate when the rear defroster is activated. The ignition must be in the ON position to operate the rear window defroster.
Controls and features 4WD CONTROL (IF EQUIPPED) This control operates the 4WD. Refer to the Driving chapter for more information. 4x4 AUTO HIGH LOW REVERSE SENSING SYSTEM (IF EQUIPPED) The reverse sensing system (RSS) sounds a tone to warn the driver of obstacles near the rear bumper when the reverse gear is selected. To help avoid personal injury, please read and understand the limitations on the reverse sensing system described below.
Controls and features The reverse sensing system detects obstacles within approximately 1.8 meters (5.9 ft.) of the rear bumper with a decreased coverage area at the outer corners of the bumper, (refer to the figures for approximate zone coverage areas). As you move closer to the obstacle, the rate of the tone increases. When the distance to the obstacle is less than 25.0 cm (10 in.), the tone will sound continuously. If the system detects a stationary or receding object further than 25.0 cm (10 in.
Controls and features USING YOUR AUDIO SYSTEM AM/FM stereo cassette VOL - PUSH ON AM FM1 BASS CLK ST TREB BAL FADE FM SEEK SCAN SIDE REW EJ TUNE 1 2 3 Volume/power control Press the control to turn the audio system on or off. Turn the control to raise or lower volume.
Controls and features If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. AM/FM select The AM/FM select control works in radio and tape modes. AM FM AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the AM control to select from AM selections, and press the FM control to select from FM1 or FM2 memory preset stations.
Controls and features Seek function in radio mode • Press to find the next listenable station down the frequency band. • Press to find the next listenable station up the frequency band. SEEK TUNE Scan function The scan function works in radio mode. SCAN Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the SCAN control again to stop the scan mode.
Controls and features Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output. BASS Treble adjust The treble adjust control allows you to increase or decrease the audio system’s treble output. TREB Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. BAL Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers.
Controls and features Tape select • To enter tape mode while in radio mode, press the TAPE AMS control. CLK TAPE AMS Automatic Music Search The Automatic Music Search feature allows you to quickly locate the beginning of the tape selection CLK being played or to skip to the next selection. TAPE To activate the feature, momentarily AMS depress the TAPE AMS button. Then, press either REW (for the beginning of the current selection) or FF (to advance to the next selection).
Controls and features Tape direction select Press SIDE and 1–2 at the same time to play the alternate side of a tape. Eject function Press the control to stop and eject a tape. SIDE REW 1-2 FF EJ DolbyT noise reduction Dolbyt noise reduction operates only in tape mode. Dolbyt reduces 4 the amount of hiss and static during tape playback. control to activate (and deactivate) Dolbyt noise reduction.
Controls and features • • to decrease hours and to increase hours. SEEK SEEK TUNE TUNE To set the minute, press and hold the CLK control and press: CLK TAPE AMS • • to decrease minutes and to increase minutes.
Controls and features AM/FM Stereo / Single CD Radio VOL - PUSH ON AM FM FM1 BASS SCN ST TREB BAL FADE CD CLK DISC SEEK EJ TUNE COMP 1 2 3 Volume/power control Press the control to turn the audio system on or off. Turn the control to raise or lower volume. 4 5 6 VOL - PUSH ON VOL - PUSH ON If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on.
Controls and features AM/FM select The AM/FM select control works in radio and CD modes. AM FM CD AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations. AM/FM select in CD mode Press this control to stop CD play and begin radio play. Tune adjust The tune control works in radio mode.
Controls and features • Press to find the next listenable station up the frequency band. Seek function in CD mode • Press to listen to the next selection. to listen to the previous • Press selection. SEEK TUNE Scan function The scan function works in radio or CD mode. SCN Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the SCAN control again to stop the scan mode.
Controls and features Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output. BASS Treble adjust The treble adjust control allows you to increase or decrease the audio system’s treble output. TREB Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers.
Controls and features Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. FADE CD select • To begin CD play (if CD[s] are loaded), press the CD control. The first track of the disc will begin playing. After that, CD play will begin where it stopped last. CD Eject function Press the control to stop and eject a CD. EJ AM FM Compression feature Compression adjust brings soft and COMP loud CD passages together for a more consistent listening level.
Controls and features • • to decrease hours and to increase hours. SEEK SEEK TUNE TUNE To set the minute, press and hold the CLK control and press: SCN CLK • • to decrease minutes and to increase minutes.
Controls and features Premium AM/FM Stereo/Cassette/Single CD/Premium Sound DISC VOL - PUSH ON EJ FM 1 AMC BL AM ST MUTE RF FM EJ DOLBY B NR TAPE CD AUTO SEEK TUNE SCAN BASS TREB REW FF SIDE 1-2 1 2 3 Volume/power control Press the control to turn the audio system on or off. Audio power can also be turned on by pressing the AM/FM select control or the tape/CD select control. Audio power is turned off by using the volume/power control. Turn control to raise or lower volume.
Controls and features If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. AM/FM select The AM/FM select control works in radio, tape and CD modes. AM FM AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations.
Controls and features Tune adjust for CD changer (if equipped) • Press to select the previous SEEK SEEK disc in the CD changer. (Play will begin on the first track of the TUNE TUNE disc unless the CD changer is in shuffle mode. Refer to Shuffle feature for more information. Hold the control to continue reversing through the remaining discs. to select the next disc • Press in the CD changer. Hold the control to fast-forward through the remaining discs.
Controls and features Seek function for CD or CD changer (if equipped) • Press to seek to the previous track of the current disc. If a selection has been playing for three seconds or more and you press , the CD changer will replay that selection from the beginning. SEEK • Press to seek forward to the TUNE next track of the current disc. After the last track has been completed, the first track of the current disc will automatically replay. Scan function The scan function works in radio, tape or CD mode.
Controls and features Setting memory preset stations AM FM 1. Select the frequency band with the AM/FM select control. 2. Select a station. Refer to Tune adjust or Seek function for more information on selecting a station. REW FF SIDE 1-2 1 2 3 4 COMP SHUFFLE 5 6 3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected.
Controls and features These stations are temporarily stored in the memory preset controls (until deactivated) and are accessed in the same manner of your original presets. To deactivate autoset and return to your audio system’s manually set memory stations, press the AUTO control again. Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output. Press the BASS control then press: to decrease the bass output • and • to increase the bass output.
Controls and features Press the BAL control then press: to shift sound to the left and • to shift sound to the right. • Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. Press the FADE control then press: • to shift the sound to the front and to shift the sound to the rear. • SEL BAL FADE SEL Tape/CD select • To begin tape play (with a tape loaded into the audio system) TAPE CD while in the radio or CD mode, press the TAPE control.
Controls and features Rewind The rewind control works in tape REW and CD modes. 1 • In tape mode, radio play will continue until rewind is stopped (with the TAPE control) or the beginning of the tape is reached. • In CD mode, pressing the REW control rewinds the CD within the current track. Fast forward The fast forward control works in FF tape and CD modes. 2 • In the tape mode, tape direction will automatically reverse when the end of the tape is reached.
Controls and features Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation. Compression adjust Compression adjust brings soft and loud CD passages together for a more consistent listening level. Press the COMP control to activate and deactivate compression adjust.
Controls and features To set the minute, press and hold the CLK control and press TUNE: AUTO CLK to decrease minutes and • to increase minutes. • If your vehicle has a separate clock module, (other than the digital radio display), the CLK button will not function in the above manner. SEEK SEEK TUNE TUNE The CLK button will allow you to switch between media display mode AUTO (radio station, stereo information, etc.) and clock display mode (time).
Controls and features Mute mode Press the control to mute the playing media. Press the control again to return to the playing media. EJ MUTE Rear seat controls (if equipped) The Personal Audio System, a - VOLUME + MODE feature of the optional Premium AM/FM Stereo/Cassette/Single CD/Premium Sound and the MACHt SEEK MEMORY Audio System with AM/FM Stereo/Cassette/Single CD, allows front and middle seat passengers to listen to different media sources (radio, cassette or CD) simultaneously.
Controls and features To activate the Personal Audio System, press the speaker/headphone control. Press the MODE control to change audio sources (for headphone mode only). Use the SEEK, VOLUME and MEMORY controls to make adjustments to the playing media. Adjusting the volume Press the + control to increase volume. Press the - control to decrease volume. From the rear seat controls, volume control can be set no higher than the current radio setting unless the speakers are turned off.
Controls and features Turning the speakers on and off Press to turn all speakers on or off. - VOLUME + MODE SEEK MEMORY Using headphones Plug a 3.5 mm headphone (not included) into the jack. Press the speaker on/off control to operate the headphones. The rear speakers will cut out once the speaker on/off control is pressed. The front speaker will remain playing for the front passengers. Press the control again to deactivate the headphones.
Controls and features Memory preset control Push the MEMORY control successively to allow rear seat passengers to scroll through the 6 memory presets in AM, FM1 or FM2. Push the MEMORY control in CD changer mode (if equipped) to advance to the next disc. Seek function • In radio mode, press to find the next listenable station down the frequency band. • In radio mode, press to find the next listenable station up the frequency band.
Controls and features MACHT Audio System with AM/FM Stereo/Cassette/Single CD DISC VOL - PUSH ON EJ FM1 MUTE ST AM FM EJ DOLBY B NR TAPE CD AUTO FADE RDS SEEK TUNE SCAN BASS TREB REW FF SIDE 1-2 1 2 3 SEL 4 BAL COMP SHUFFLE 5 6 Your audio system is equipped with selective lighting, a unique lighting strategy. This lighting feature is operable when the headlamps are illuminated.
Controls and features Turn control to raise or lower volume. VOL - PUSH ON If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. If you wish to maintain your preset volume level, turn the audio system off with the power control before switching off the ignition. AM/FM select The AM/FM select control works in radio, tape and CD modes.
Controls and features Tune adjust in radio mode • Press to move to the next frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly. • Press to move to the next frequency up the band (whether or not a listenable station is located there). Hold for quick movement. SEEK SEEK TUNE TUNE Tune adjust for CD changer (if equipped) • Press to select the previous SEEK disc in the CD changer.
Controls and features Seek function in tape mode • Press to listen to the previous selection on the tape. to listen to the next selection on the tape. • Press Seek function for CD changer (if equipped) • Press to seek to the previous track of the current disc. If a selection has been playing for three seconds or more and you , the CD changer will press replay that selection from the beginning. SEEK • Press to seek forward to the TUNE next track of the current disc.
Controls and features Radio station memory preset The radio is equipped with six station memory preset controls. These controls can be used to select up to six preset AM stations and twelve FM stations (six in FM1 and six in FM2). Setting memory preset stations 1. Select the frequency band with AM FM the AM/FM select control. 2. Select a station. Refer to Tune adjust or Seek function for more information on selecting a station. 3.
Controls and features Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output. Press the BASS control then press: • to decrease bass output and to increase bass output. • Treble adjust The treble adjust control allows you to increase or decrease the audio system’s treble output. Press the TREB control then press: to decrease treble output and • to increase treble output.
Controls and features • • to shift sound to the left and to shift sound to the right. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. Press the FADE control then press: • to shift sound to the front and to shift sound to the rear. • SEL BAL FADE SEL Tape/CD/CD changer (if equipped) select • To begin tape play (with a tape loaded into the audio system) TAPE CD while in the radio or CD mode, press the TAPE control.
Controls and features Rewind The rewind control works in tape REW and CD modes. 1 • In tape mode, radio play will continue until rewind is stopped (with the TAPE control) or the beginning of the tape is reached. • In CD mode, pressing the REW control for less than three seconds results in slow rewind. Pressing the control for more than three seconds results in fast rewind. Fast forward The fast forward control works in FF tape and CD modes.
Controls and features Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation. Compression adjust Compression adjust brings soft and loud CD passages together for a more consistent listening level. Press the COMP control to activate and deactivate compression adjust.
Controls and features To set the minute, press the clock/RDS control until SELECT MIN is displayed and press: AUTO RDS • • to decrease minutes and to increase minutes. Radio Data System (RDS) feature This feature allows your audio system to receive text information from RDS-equipped FM radio stations. Press and hold the control for three seconds to turn the feature on or off.
Controls and features RDS traffic announcement • Press the RDS control until TRAFFIC is displayed. AUTO RDS • Use the SELECT control to select ON or OFF. With the feature ON, use the SEEK or SCAN control to find a radio station broadcasting a traffic report (if it is broadcasting RDS data). RDS select program type • Press the RDS control until FIND program type is displayed. SEL AUTO RDS • Use the SEL control to select the program type.
Controls and features • • • • • • • • Classic Country Info Jazz/R&B Religious Rock Soft Top 40 RDS show • With the RDS menu enabled, press the RDS control until SHOW is displayed. AUTO RDS • Use the SEL control to select TYPE, NAME, TEXT or NONE. When your radio is turned to a RDS station, RDS station TYPE, station NAME, or TEXT message will be displayed along with the frequency. Press SEL in order to scroll through the text messages. Mute mode Press the control to mute the playing media.
Controls and features Rear seat controls (if equipped) The Personal Audio System, a - VOLUME + MODE feature of the optional Premium AM/FM Stereo/Cassette/Single CD/Premium Sound and the MACHt SEEK MEMORY Audio System with AM/FM Stereo/Cassette/Single CD, allows front and middle seat passengers to listen to different media sources (radio, cassette or CD) simultaneously. However, the front and middle-seat passengers cannot listen to two different radio stations at the same time.
Controls and features Adjusting the volume Press the + control to increase volume. Press the - control to decrease volume. - VOLUME + MODE SEEK MEMORY - VOLUME + MODE SEEK MEMORY From the rear seat controls, volume control can be set no higher than the current radio setting unless the speakers are turned off. Refer to Turning speakers on and off. Turning the speakers on and off Press to turn all speakers on or off. - VOLUME + MODE SEEK MEMORY Using headphones Plug a 3.
Controls and features The rear speakers will cut out once the speaker on/off control is pressed. The front speaker will remain playing for the front passengers. Press the control again to deactivate the headphones. Mode select Push the MODE control to toggle between AM, FM1, FM2, tape, CD or CD changer (if equipped). Memory preset control Push the MEMORY control successively to allow rear seat passengers to scroll through the 6 memory presets in AM, FM1 or FM2.
Controls and features • In CD mode (if equipped), use the SEEK function to access the next or previous selection. CD changer (if equipped) The CD changer is located in one of the following locations: • in the trunk • in the center console • under the driver’s seat 1. Slide the door to access the CD changer magazine. 2. Press to eject the magazine. 3. Turn the magazine (A) over. 4. Using the disc holder release knob (C), pull the disc holder (B) out of the magazine.
Controls and features A If you pull too hard on the disc holder, the disc holder may come completely out of the magazine. If this happens, reinsert the disc holder back into the magazine while pressing on the lever (A). 5. Line up the CD with the groove of the disc holder. Ensure that the label on the CD faces downwards. 6. Press in on the disc holder until it locks securely into the magazine. If the disc holders are not fully locked into the magazine, the unit will not operate.
Controls and features The CD magazine may be inserted or ejected with the radio power off. ONLY use the magazine supplied with the CD changer, other types will damage the unit. Keep the CD changer door closed. Coins and foreign objects will damage the CD player and void your audio system warranty. Troubleshooting the CD changer (if equipped) The laser beam used in the compact disc player is harmful to the eyes. Do not attempt to disassemble the case.
Controls and features Cleaning cassette player (if equipped) Clean the tape player head with a cassette cleaning cartridge after ten to twelve hours of play in order to maintain the best sound and operation. Cassette and cassette player care • Use only cassettes that are 90 minutes long or less. • Do not expose tapes to direct sunlight, high humidity, extreme heat or extreme cold. Allow tapes that may have been exposed to extreme temperatures to reach a moderate temperature before playing.
Controls and features • Station overload. Weak signals are sometimes captured by stronger signals when you pass a broadcast tower. A stronger signal may temporarily overtake a weaker signal and play while the weak station frequency is displayed. The audio system automatically switches to single channel reception if it will improve the reception of a station normally received in stereo. Audio system warranties and service Refer to the “Warranty Guide” for audio system warranty information.
Controls and features SPEED CONTROL (IF EQUIPPED) To turn speed control on • Press ON. Vehicle speed cannot be controlled until the vehicle is traveling at or above 48 km/h (30 mph). ON OFF Do not use the speed control in heavy traffic or on roads that are winding, slippery, or unpaved. Do not shift the gearshift lever into N (Neutral) with the speed control on. To turn speed control off • Press OFF or • Turn off the vehicle ignition.
Controls and features To set a speed • Press SET/SET ACC/SET ACCEL. For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph). RSM SET ACC COAST If you drive up or down a steep hill, your vehicle speed may vary momentarily slower or faster than the set speed. This is normal. Speed control cannot reduce the vehicle speed if it increases above the set speed on a downhill.
Controls and features You can accelerate with the accelerator pedal at any time during speed control usage. Releasing the accelerator pedal will return your vehicle to the previously programmed set speed. To set a lower set speed • Press and hold CST/COAST. Release the control when the desired speed is reached or • Press and release CST/COAST. Each press will decrease the set speed by 1.6 km/h (1 mph) or RSM SET ACC COAST • Depress the brake pedal.
Controls and features To disengage speed control • Depress the brake pedal or • Depress the clutch pedal (if equipped) Disengaging the speed control will not erase the previously programmed set speed. Pressing OFF will erase the previously programmed set speed.
Controls and features To return to a previously set speed • Press RES/RSM/RESUME. For RES/RSM/RESUME to operate, the vehicle speed must be faster than 48 km/h (30 mph). RSM SET ACC COAST Indicator light This light comes on when either the SPEED SET ACC/SET ACCEL or RES/RSM/RESUME controls are CONT pressed. It turns off when the speed control OFF control is pressed, the brake is applied or the ignition is turned to the OFF position.
Controls and features TILT STEERING WHEEL (IF EQUIPPED) Pull the tilt steering control toward you to move the steering wheel up or down. Hold the control while adjusting the wheel to the desired position, then release the control to lock the steering wheel in position. Never adjust the steering wheel when the vehicle is moving. HAZARD FLASHER For information on the hazard flasher control, refer to Hazard flasher in the Roadside emergencies chapter.
Controls and features Push the control on the end of the stalk to activate washer. Push and hold for a longer wash cycle. The washer will automatically shut off after ten seconds of continuous use. Speed dependent wipers When the windshield wiper control is set on the intermittent settings, speed-sensitive front wipers automatically adjust as the vehicle’s speed increases. Rear window wiper and washer For rear wiper operation, rotate the rear window wiper and washer control to the desired interval position.
Controls and features Radio control features • Press BAND/MODE to select AM, FM1, FM2, TAPE or CD (if equipped). In Radio mode: • Press MEM/NEXT to select a preset station from memory. NEXT MODE In Tape mode: • Press MEM/NEXT to listen to the next selection on the tape. In CD mode: • Press MEM/NEXT to listen to the next track on the disc. In any mode: • Press VOL up or down to adjust the volume. Climate control features • Press TEMP up or down to adjust temperature.
Controls and features N OPE Storage compartment (if equipped) Press the OPEN control to open the storage compartment. The door will open slightly and can be moved to full open. P LAM DE MO P LAM Installing a garage door opener (if equipped) The storage compartment can be converted to accommodate a variety of aftermarket garage door openers: • Remove the storage clip from the door. • Place Velcroy hook onto side of aftermarket transmitter opposite of actuator control.
Controls and features • Press the GARAGE control to activate the transmitter. Moon roof (if equipped) You can move the moon roof back to open the glass panel or tilt up to ventilate the vehicle. To open the moon roof: The moon roof is equipped with an automatic, one-touch, express opening feature. Press and release the rear portion of the control. To stop motion at any time during the one-touch opening, press the control a second time.
Controls and features Electronic compass/temperature display (if equipped) Outside air temperature The outside temperature display is contained in the overhead console. The temperature display can be turned off and on by pressing the MODE control on the overhead console. The temperature can be displayed in Centigrade or Fahrenheit by pressing the MODE control. If the outside temperature falls below 3.
Controls and features Compass zone adjustment 1. Determine which magnetic zone you are in by referring to the zone map. 1 15 2 14 3 13 4 12 11 5 6 10 7 2. Press and hold the MODE control until VAR appears in the display, then release. The display should show the current zone number. 3. Press the MODE control until the desired zone number appears. The display will flash and then return to normal operation. The zone is now updated.
Controls and features Compass calibration adjustment Perform this adjustment in an open area free from steel structures and high voltage lines: • Press and hold the MODE control until CAL appears in the display (approximately eight seconds) and release. • Drive the vehicle slowly (less than 5 km/h [3 mph]) in circles until CAL indicator turns off in about 2–3 complete circles.
Controls and features Programming 1. Prepare for programming the HomeLinkt Universal Transceiver by erasing the three factory default REC DEL PLAY codes by holding down the two outside buttons until the red light begins to flash after 20 seconds. Release both buttons. 2. Hold the end of your hand-held transmitter 5–14 cm (2–5 inches) away from the HomeLinkt Universal Transceiver surface (located on your visor) while keeping the red light in view. 3.
Controls and features Operating the HomeLinkT Universal Transceiver Once programmed, the HomeLinkt Universal Transceiver can be used in place of hand-held transmitters. To REC operate, simply press and release the appropriate HomeLinkt button (the red light will illuminate, indicating the signal is being transmitted).
Controls and features The 2nd or 3rd press from step 3 will activate the door. The HomeLinkt Universal Transceiver has now been trained to the receiver. The remaining two buttons may now be programmed if this has not previously been done. Erasing HomeLinkT buttons Individual buttons cannot be erased, however, to erase the three programmed buttons: REC DEL PLAY 1. Hold down the two outside buttons until the red light begins to flash after 20 seconds. 2. Release both buttons.
Controls and features To record a message: 1. Press and release the REC button one time to start recording. REC DEL PLAY (An audible tone will sound, confirming the onset of recording). 2. Press and release the REC button a second time to end recording. (An audible tone will sound again, confirming the end of recording and the red indicator light will turn off.) 3. While a message is being recorded, the indicator light will be a solid red. 4.
Controls and features If the DEL button is inadvertently pressed or the time allotted (5 seconds) has passed, the indicator light will flash amber and an “error” tone will sound. AUTOLAMP DELAY SYSTEM (IF EQUIPPED) The autolamp sets the headlamps to turn on and off automatically. The autolamp may be set to: • turn on the lamps automatically at night • turn off the lamps automatically during daylight • keep the lamps on for up to three minutes after the key is turned to OFF Setting autolamp 1.
Controls and features Automatic dimming rear view mirror The autolamp/automatic dimming mirror is equipped with an automatic dimming feature. This feature will change from the normal state to the non-glare “active” state when bright lights (glare) reach the mirror. When the mirror detects bright light from front or behind, it will adjust automatically to minimize glare.
Controls and features One touch down • Press AUTO completely down and release quickly. The driver’s window will open fully. Depress again to stop window operation. AUTO Window lock The window lock feature allows only the driver to operate the power windows. WINDOW LOCK To lock out all the window controls except for the driver’s press the left side of the control. Press the right side to restore the window controls. POWER DOOR LOCKS (IF EQUIPPED) Press U to unlock all doors and L to lock all doors.
Controls and features CHILDPROOF DOOR LOCKS When these locks are set, the rear doors cannot be opened from the inside. The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on rear edge of each rear door and must be set separately for each door. Setting the lock for one door will not automatically set the lock for both doors. Move lock control up to engage the lock. Move control down to disengage childproof locks.
Controls and features Heated outside mirrors (if equipped) Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated. Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place. These actions could cause damage to the glass and mirrors. CENTER CONSOLE Your vehicle may be equipped with a variety of console features.
Controls and features Auxiliary power point The power point is an additional power source for electrical accessories. Rear console features The rear console incorporates the following features: • air vents • audio system controls • rear seat climate controls • cupholders CENTER ARMREST/REAR CUPHOLDER Do not attempt to raise the console armrest when the rear cupholder is in use. If you find resistance when raising the armrest, make sure the cupholder is fully closed or else damage may occur to the armrest.
Controls and features POSITIVE RETENTION FLOOR MAT To install floor mats: 1. Move the driver’s seat to the most rearward position 2. Position the driver’s side floor mat with the rear of the mat against left (outboard) front edge of seat track mounting bracket. 3. Use a screwdriver to screw locator post into vehicle carpeting. Exert pressure while turning to pierce the carpeting. When installed properly, the locator will not screw down tightly, but will rotate freely.
Controls and features Make sure that the liftgate door and/or window are closed to prevent exhaust fumes from being drawn into the vehicle. This will also prevent passengers and cargo from falling out. If you must drive with the liftgate door or window open, keep the vents open so outside air comes into the vehicle. CARGO COVER (IF EQUIPPED) Your vehicle may be equipped with a cargo area shade that covers the luggage compartment of your vehicle. To install the shade: 1.
Controls and features 2. Wrap the vinyl around the roller tube twice. Tuck the edges of the vinyl inside the end cap with each wrap. 3. Fold the edges of the vinyl towards the center, making sure that the edges clear the end cap slots. Use tape or a rubber band to hold the vinyl to the left side of the tube. 4. Push in the right end cap (marked RH) about 1⁄4 of the total length to disengage the clutch and hold the end cap in while turning the roller tube toward you 14 times. 5. Let go of the right end cap.
Controls and features Unlocking the doors Press this control to unlock the driver’s door. The interior lamps will illuminate. Press the control a second time within five seconds to unlock all doors. Locking the doors Press this control to lock all doors. To confirm all doors are closed and locked, press the control a second time within five seconds. The doors will lock again, the horn will chirp and the lamps will flash.
Controls and features Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Memory seat feature (if equipped) The remote entry system can also control the memory seat feature. Press the control once to unlock the driver’s door and move the memory seat feature to the corresponding memory position, just as if you had pressed the memory control in the vehicle.
Controls and features The memory feature will continue to work from the door control even when deactivated at the remote entry module. Replacing the battery The transmitter is powered by one coin type three-volt lithium battery CR2032 or equivalent. Typical operating range will allow you to be up to 10 meters (33 feet) away from your vehicle.
Controls and features Replacing lost transmitters Take all your vehicle’s transmitters to your dealer if service is required. If you purchase additional transmitters (up to four may be programmed), perform the following procedure: To reprogram the transmitters yourself, place the key in the ignition and turn from OFF to ON eight times in rapid succession (within 10 seconds) ending in ON. After doors lock/unlock, press any control on all transmitters (up to four). When completed, turn the ignition to OFF.
Controls and features The autolock feature repeats when: • any door is opened and then closed • the brake pedal is released Deactivating autolock Before following the activation or deactivation procedures, make sure that the ignition is OFF and all vehicle doors and liftgate window are closed. 1. Enter the 5 digit entry code. 2. Press and release the 3/4 control while holding the 7/8 control. 1 2 3 4 5 6 7 8 9 0 3. Release the 7/8 control.
Controls and features If autolock/relock has been changed, the horn will chirp to confirm procedure is complete. Keyless entry system (if equipped) With the keyless entry keypad, you can: 1 2 3 4 5 6 7 8 9 0 • lock or unlock the vehicle doors without using the key • activate/deactivate the autolock feature See also Remote entry system in this chapter for more information. Your vehicle has a factory-set 5–digit code that operates the keyless entry system.
Controls and features If you wish to erase your personal code, use the following instructions: Erasing personal code 1. Enter the factory-set code. 2. Press 1/2 within five seconds of step 1. 3. Press the 7/8 and 9/0 controls at the same time within five seconds of step two. The system will now only respond to the factory-set code.
Controls and features SECURILOCKY PASSIVE ANTI-THEFT SYSTEM The SecuriLocky passive anti-theft system provides an advanced level of vehicle theft protection. Your vehicle’s engine can only be started with the two special SecuriLocky electronically coded keys provided with your vehicle. Each time you start your vehicle, the SecuriLocky key is read by the SecuriLocky passive anti-theft system.
Controls and features Programming spare SecuriLockY keys Spare SecuriLocky keys can be purchased from your dealership and programmed to your SecuriLocky passive anti-theft system (up to a total of 8 keys). Your dealership can program your new SecuriLocky key(s) to your vehicle or you can do it yourself using the following simple procedure. To program a new SecuriLocky key yourself, you will need two previously programmed SecuriLocky keys (keys that already operate your vehicle’s engine).
Controls and features 5. Within 10 seconds of turning the ignition to OFF, insert the unprogrammed SecuriLocky key (new key) into the ignition and turn the ignition from OFF to RUN (maintain ignition in RUN for at least one second). This step will program your new SecuriLocky key. 6. To program additional SecuriLocky key(s), repeat this procedure from step 1. If the programming procedure was successful, the new SecuriLocky key(s) will start the vehicle’s engine.
Seating and safety restraints SEATING Adjustable head restraints Your vehicle’s seats may be equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible. Refer to the following to raise and lower the head restraints.
Seating and safety restraints Adjusting the front power seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop. Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Press to raise or lower the front portion of the seat cushion. Press to raise or lower the rear portion of the seat cushion.
Seating and safety restraints Memory seats (if equipped) This system allows automatic positioning of the driver seat to three programmable positions. SET The memory seat control is located on the driver door. • To program position one, move the driver seat to the desired 1 2 position using the seat controls. Press the SET control. The SET control indicator light will briefly illuminate. While the light is illuminated, press control 1. • To program position two, repeat the previous procedure using control 2.
Seating and safety restraints head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible. Refer to the following to raise and lower the head restraints. Push or pull the head rests to the desired position.
Seating and safety restraints To return the seat to the upright position: • Press downward on the upper corner of the seatback and hold. • Pull the release handle upward to unlatch the seat. • Rotate the seatback upward until the seatback latches in the upright position. The seatback will click when it is locked into position. PUSH PUS H SAFETY RESTRAINTS Safety restraints precautions Always drive and ride with your seatback upright and the lap belt snug and low across the hips.
Seating and safety restraints All occupants of the vehicle, including the driver, should always properly wear their safety belts, even when an air bag SRS is provided. It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts.
Seating and safety restraints 2. To unfasten, push the release button and remove the tongue from the buckle. The front and rear outboard safety restraints in the vehicle are combination lap and shoulder belts. The front and rear seat passenger outboard safety belts have two types of locking modes described below: Vehicle sensitive mode The vehicle sensitive mode is the normal retractor mode, allowing free shoulder belt length adjustment to your movements and locking in response to vehicle movement.
Seating and safety restraints How to use the automatic locking mode • Buckle the combination lap and shoulder belt. • Grasp the shoulder portion and pull downward until the entire belt is extracted. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode.
Seating and safety restraints • This seat belt system has a retractor assembly that is designed to pay out webbing in a controlled manner. This feature is designed to help reduce the belt force acting on the occupant’s chest.
Seating and safety restraints Safety belt extension assembly If the safety belt assembly is too short, even when fully extended, 20 cm (8 inches) can be added to the safety belt assembly by adding a safety belt extension assembly (part number 611C22). Safety belt extension assemblies can be obtained from your dealer at no cost. Use only extensions manufactured by the same supplier as the safety belt. Manufacturer identification is located at the end of the webbing on the label.
Seating and safety restraints Safety belt maintenance Inspect the safety belt systems periodically to make sure they work properly and are not damaged. Inspect the safety belts to make sure there are no nicks, wears or cuts, replacing if necessary.
Seating and safety restraints Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. Air bags DO NOT inflate slowly or gently and the risk of injury from a deploying air bag is greatest close to the trim covering the air bag module.
Seating and safety restraints Do not attempt to service, repair, or modify the Air Bag Supplemental Restraint System or its fuses. See your Ford or Lincoln-Mercury dealer. Children and air bags For additional important safety information, read all information on safety restraints in this guide. Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position.
Seating and safety restraints The air bags inflate and deflate rapidly upon activation. After air bag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the air bag. Small amounts of sodium hydroxide may be present which may irritate the skin and eyes, but none of the residue is toxic.
Seating and safety restraints • and the electrical wiring which connects the components. The diagnostic module monitors its own internal circuits and the supplemental air bag electrical system warning (including the impact sensors), the system wiring, the air bag system readiness light, the air bag back up power and the air bag ignitors. Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system.
Seating and safety restraints All occupants of the vehicle including the driver should always wear their safety belts even when an air bag SRS is provided. How does the side air bag system work? The side air bag system consists of the following: • An inflatable nylon bag (air bag) with a gas generator concealed behind the outboard bolster of the driver and front passenger seatbacks. • A special seat cover designed to allow airbag deployment.
Seating and safety restraints The fact that the air bags did not inflate in a collision does not mean that something is wrong with the system. Rather, it means the forces were not of the type sufficient to cause activation. Side air bags are designed to inflate in side-impact collisions, not roll-over, rear-impact, frontal or near-frontal collisions, unless the collision causes sufficient lateral deceleration. Several air bag system components get hot after inflation. Do not touch them after inflation.
Seating and safety restraints Disposal of air bags and air bag equipped vehicles For disposal of air bags or air bag equipped vehicles, see your local dealership or qualified technician. Air bags MUST BE disposed of by qualified personnel. SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safety restraints for children. Also see Air Bag Supplemental Restraint System (SRS) in this chapter for special instructions about using air bags.
Seating and safety restraints If the shoulder belt portion of a combination lap and shoulder belt can be positioned so it does not cross or rest in front of the child’s face or neck, the child should wear the lap and shoulder belt. Moving the child closer to the center of the vehicle may help provide a good shoulder belt fit. Do not leave children, unreliable adults, or pets unattended in your vehicle.
Seating and safety restraints When installing a child safety seat: • Review and follow the information presented in the Air Bag Supplemental Restraint System section in this chapter. • Use the correct safety belt buckle for that seating position. • Insert the belt tongue into the proper buckle until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle.
Seating and safety restraints Installing child safety seats in combination lap and shoulder belt seating positions 1. Position the child safety seat in a seat with a combination lap and shoulder belt. An air bag can kill or injure a child in a child seat. If you must use a forward-facing child seat in the front seat, move seat all the way back. Children 12 and under should be properly restrained in the rear seat whenever possible. 2.
Seating and safety restraints 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until you hear a snap and feel the latch engage. Make sure the tongue is latched securely by pulling on it. 5.
Seating and safety restraints 7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with your knee on the child seat. 8. Allow the safety belt to retract to remove any slack in the belt. 9. Before placing the child in the seat, forcibly tilt the seat forward and back to make sure the seat is securely held in place. 10.
Seating and safety restraints The provision (attaching hole) is provided in the rear edge of the front passenger seat cushion frame. The anchorbracket must be installed using the instructions provided with the kit. Tether anchorage hardware kits (part number 613D74) including instructions, may be obtained at no charge from any Ford or Lincoln-Mercury dealer. Tighten the anchor according to specifications.
Starting PREPARING TO START YOUR VEHICLE Engine starting is controlled by the ignition system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting. Only use the accelerator when you have difficulty starting the engine. For more information on starting the vehicle, refer to Starting the engine in this chapter.
Starting If starting a vehicle with an automatic transmission: • Make sure the parking brake is set. • If • • Make sure the gearshift is in P (Park). starting a vehicle with a manual transmission: Make sure the parking brake is set. Push the clutch pedal to the floor. 3. Turn the key to 4 (ON) without turning the key to 5 (START).
Starting DOOR AJAR CHECK GAGE 4 F 20 10 0 RPMx1000 ! E 60 70 80 0 0 0 80 100 BRAKE P 40 90 120 60 30 1 ABS 50 40 2 C
Starting 4. After idling for a few seconds, apply the brake and release the parking brake. Using the engine block heater (if equipped) An engine block heater warms the engine coolant, which improves starting, warms up the engine faster and allows the heater-defroster system to respond quickly. Use of an engine block heater is strongly recommended if you live in a region where temperatures reach -23°C (-10°F) or below. For best results, plug the heater in at least three hours before starting the vehicle.
Starting Important ventilating information If the engine is idling while the vehicle is stopped in an open area for long periods of time, open the windows at least 2.5 cm (one inch). Adjust the heating or air conditioning (if equipped) to bring in fresh air. Improve vehicle ventilation by keeping all air inlet vents clear of snow, leaves and other debris.
Driving BRAKES Your service brakes are self-adjusting. Refer to the maintenance guide and or service guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the brakes are applied.
Driving ABS warning lamp The ABS warning lamp in the instrument cluster momentarily illuminates when the ignition is turned on and the engine is off. If the light does not illuminate momentarily at start up, remains on or continues to flash, the ABS needs to be serviced. With the ABS light on, the anti-lock brake system is disabled and normal ! braking is still effective unless the BRAKE brake warning light also remains illuminated with parking brake released.
Driving The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned ON) until the parking brake is released. ! BRAKE Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park) (automatic transmission) or in 1 (First) (manual transmission). The parking brake is not recommended to stop a moving vehicle. However, if the normal brakes fail, the parking brake can be used to stop your vehicle in an emergency.
Driving • • • • • underinflated tire(s) on any wheel(s) high crown in center of road high crosswinds wheels out of alignment loose or worn components in steering linkage AIR SUSPENSION SYSTEM (IF EQUIPPED) The load leveling feature of the air suspension automatically keeps the vehicle at a constant level if a load is added or removed from the vehicle.
Driving TRANSMISSION OPERATION Automatic transmission operation Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift from being moved from P (Park) unless the brake pedal is depressed. If you cannot move the gearshift out of P (Park) with the brake pedal depressed: 1. Apply the parking brake, turn ignition key to LOCK, then remove the key. 2. Insert the key and turn it to OFF. Apply the brake pedal and shift to N (Neutral). 3. Start the vehicle.
Driving Driving with a 4–speed automatic transmission (if equipped) Understanding gearshift positions Pull the gearshift lever towards you and downward to move the automatic gearshift. Hold the brake pedal down while you move the gearshift lever from P (Park) to another position. If you do not hold the brake pedal down, your vehicle may move unexpectedly and injure someone. P (Park) Always come to a complete stop before shifting into P (Park). Make sure the gearshift is securely latched in P (Park).
Driving (Overdrive) The normal driving position for the best fuel economy. Transmission operates in gears one through four. (Overdrive) can be deactivated by pressing the transmission control switch on the end of the gearshift lever. The transmission control indicator light (TCIL) will illuminate on the instrument cluster. O/D ON/OFF O/D OFF Drive – Not shown on the display. Activate by pressing the transmission control switch on the end of the gearshift lever with the gearshift in the position.
Driving 1 (First) Use 1 (Low) to provide maximum engine braking on steep downgrades. Upshifts can be made by shifting to 2 (Second) or to (Overdrive). Selecting 1 (Low) at higher speeds causes the transmission to shift to a lower gear, and will shift to 1 (Low) after vehicle decelerates to the proper speed. Driving with a 5–speed automatic transmission (if equipped) Understanding gearshift positions Hold the brake pedal down while you move the gearshift lever from P (Park) to another position.
Driving N (Neutral) With the gearshift in N (Neutral), the vehicle can be started and is free to roll. Hold the brake pedal down while in this gear. (Overdrive) The normal driving position for the best fuel economy. Transmission operates in gears one through five. (Overdrive) can be deactivated by pressing the transmission control switch on the end of the gearshift lever. The transmission control indicator light (TCIL) will illuminate on the instrument cluster.
Driving 2 (Second) Use 2 (Second) to start-up on slippery roads or to provide additional engine braking on downgrades. Transmission operates in third gear. 1 (First) Use 1 (First) to provide maximum engine braking on steep downgrades. Upshifts can be made by shifting to 2 (Second) or to (Overdrive). Selecting 1 (Low) at higher speeds causes the transmission to shift to a lower gear and will shift to 1 (First) after the vehicle decelerates to the proper vehicle speed.
Driving 5. Release the clutch slowly while pressing gradually down on the accelerator pedal. • Do not drive with your foot resting on the clutch pedal. Do not use the clutch to hold your vehicle at a standstill while waiting on a hill. These actions may reduce clutch life. Parking 1. Apply the brake and shift into N (Neutral). 2. Engage the parking brake. 3. Shift into 1 (First). 4. Turn the ignition to Off. Do not park your vehicle in Neutral, it may move unexpectedly and injure someone.
Driving Recommended shift speeds Upshifts when accelerating (for best fuel economy) Transfer case position (if equipped) Shift from: AUTO or HIGH LOW 1-2 14 km/h (10 mph) 5 km/h (4 mph) 2-3 32 km/h (22 mph) 11 km/h (9 mph) 3 -4 50 km/h (33 mph) 19 km/h (13 mph) 4 - 5 (Overdrive) 71 km/h (41 mph) 27 km/h (17 mph) Upshifts when cruising (recommended for best fuel economy) Transfer case position (if equipped) Shift from: AUTO or HIGH LOW 1 -2 16 km/h (10 mph) 6 km/h (4 mph) 2-3 26 km/h (19 mph) 10 km/h (8 mph)
Driving FOUR-WHEEL DRIVE (4WD) OPERATION (IF EQUIPPED) If equipped with the Electronic Shift 4WD System, and the instrument panel control is moved to 4WD Low while the vehicle is moving, the system will not engage and no damage will occur to the 4WD system. All utility-type vehicles and 4WD vehicles have special design and equipment features to make them capable of performing in a wide variety of off-road applications.
Driving • The 4WD HIGH mode provides four-wheel drive with full power to both axles. It is only intended for severe winter or off-road conditions, such as deep snow and ice (where no dry or wet pavement remains uncovered), and shallow sand. • The 4WD LOW mode supplies four-wheel drive with full power to both axles and includes a lower gear ratio for low-speed.
Driving Using the Control-Trac system Shifting between 4WD AUTO and 4WD HIGH When you move the control to 4WD HIGH, the indicator light will 4x4 illuminate in the instrument cluster. HIGH LOW AUTO When you move the control to 4WD AUTO, the indicator light will turn off. Either shift can be done at a stop or while driving at any speed. Shifting from 4WD AUTO or 4WD HIGH to 4WD LOW 1. Bring the vehicle to a stop. 2. Depress the brake. 4x4 AUTO HIGH LOW 3.
Driving Driving off-road with 4WD Your vehicle is specially equipped for driving on sand, snow, mud and rough terrain and has operating characteristics that are somewhat different from conventional vehicles, both on and off the road. Maintain steering wheel control at all times, especially in rough terrain. Since sudden changes in terrain can result in abrupt steering wheel motion, make sure you grip the steering wheel from the outside. Do not grip the spokes.
Driving Once through water, always try the brakes. Wet brakes do not stop the vehicle as effectively as dry brakes. Drying can be improved by moving your vehicle slowly while applying light pressure on the brake pedal. After driving through mud, clean off residue stuck to rotating driveshafts and tires. Excess mud stuck on tires and rotating driveshafts causes an imbalance that could damage drive components.
Driving Driving on snow and ice A 4WD vehicle has advantages over 2WD vehicles in snow and ice but can skid like any other vehicle. Avoid sudden applications of power and quick changes of direction on snow and ice. Apply the accelerator slowly and steadily when starting from a full stop. When braking, apply the brakes as you normally would. In order to allow the anti-lock brake system (ABS) to operate properly, keep steady pressure on the brake pedal.
Driving You should either know the terrain or examine maps of the area before driving. Map out your route before driving in the area. For more information on driving off-road, read the “Four Wheeling” supplement in your owner’s portfolio. If your vehicle gets stuck If the vehicle is stuck in mud or snow it may be rocked out by shifting from forward and reverse gears, stopping between shifts, in a steady pattern. Press lightly on the accelerator in each gear.
Driving If the rear axle is submerged in water, the rear axle lubricant should be checked and changed, if necessary. The rear axle is filled with a synthetic lubricant and does not normally require a lubricant change for the life of the vehicle. Rear axle lubricant quantities should not need to be checked unless a leak is suspected. Driving on hilly or sloping terrain When driving on a hill, avoid driving crosswise or turning on steep slopes. You could lose traction and slip sideways.
Driving TRACTION-LOK AXLE (IF EQUIPPED) This axle provides added traction on slippery surfaces, particularly when one wheel is on a poor traction surface. Under normal conditions, the Traction-Lok axle functions like a standard rear axle. Extended use of other than the manufacturer’s specified size tires on a Traction-Lok rear axle could result in a permanent reduction in effectiveness. This loss of effectiveness does not affect normal driving and should not be noticeable to the driver.
Driving • Maximum Trailer Weight Rating : Maximum weight of a trailer the vehicle is permitted to tow. The maximum trailer weight rating is determined by subtracting the vehicle curb weight for each engine/transmission combination, any required option weight for trailer towing and the weight of the driver from the GCWR for the towing vehicle. • Maximum Trailer Weight : maximum weight of a trailer the loaded vehicle (including passengers and cargo) is permitted to tow.
Driving Calculating the load your vehicle can carry/tow 1. Use the appropriate maximum gross combined weight rating (GCWR) chart to find the maximum GCWR for your type engine and rear axle ratio. 2. Weigh your vehicle as you customarily operate the vehicle without cargo. To obtain correct weights, try taking your vehicle to a shipping company or an inspection station for trucks. 3. Subtract your loaded vehicle weight from the maximum GCWR on the following charts.
Driving TRAILER TOWING Trailer towing with your vehicle may require the use of a trailer tow option package. Trailer towing puts additional loads on your vehicle’s engine, transmission, axle, brakes, tires, and suspension. For your safety and to maximize vehicle performance, be sure to use the proper equipment while towing. Follow these guidelines to ensure safe towing procedure: • Stay within your vehicle’s load limits. • Thoroughly prepare your vehicle for towing.
Driving Trailer towing table (4x2 manual transmission) GCWR (Gross Combined Weight Rating)/Trailer weights Trailer weight Rear Maximum Maximum range-kg Engine axle GCWR-kg frontal area of (lbs.) ratio (lbs.) trailer-m2 (ft2) (0-Maximum) 2-door 2 721 0-907 4.64 4.0L OHV 3.27 (6 000) (0-2 000) (50) 3 175 0-1 433 4.64 4.0L OHV 3.73 (7 000) (0-3 160) (50) 4-door 2 721 0-889 4.64 4.0L OHV 3.27 (6 000) (0-1 960) (50) 3 175 0-1 343 4.64 4.0L OHV 3.
Driving Trailer towing table (4x4 manual transmission) GCWR (Gross Combined Weight Rating)/Trailer weights Trailer weight Rear Maximum Maximum range-kg Engine axle GCWR-kg frontal area of (lbs.) ratio (lbs.) trailer-m2 (ft2) (0-Maximum) 2-door 3.27 2 721 0-880 4.64 4.0L OHV (6 000) (0-1 940) (50) 3.55 2 948 0-1 107 4.64 4.0L OHV (6 500) (0-2 440) (50) 3.73 3 175 0-1 334 4.64 4.0L OHV (7 000) (0-2 940) (50) 4.10 3 175 0-1 334 4.64 4.0L OHV (7 000) (0-2 940) (50) 4-door 2 948 0-1 007 4.64 4.0L OHV 3.
Driving Trailer towing table (4x2 automatic transmission) GCWR (Gross Combined Weight Rating)/Trailer weights Trailer Weight Rear Maximum Maximum Range-kg Engine axle GCWR-kg frontal area of (lbs.) ratio (lbs.) trailer-m2 (ft2) 0-Maximum 2-door 4.0L 3.27 3 402 0-1 361 4.64 SOHC (7 500) (0-3 000) (50) 4.0L 3.55 3 856 0-2 041 4.64 SOHC (8 500) (0-4 500) (50) 3.73 4 082 0-2 313 4.64 4.0L OHV (9 000) (0-5 100) (50) 4.0L 3.73 4 082 0-2 313 4.64 SOHC (9 000) (0-5 100) (50) 4-door 4.0L 4 082 0-2 041 4.64 3.
Driving Trailer towing table (4x4 and AWD with automatic transmission) GCWR (Gross Combined Weight Rating)/Trailer Weights Trailer Weight Rear Maximum Maximum Range-kg Engine axle GCWR-kg frontal area of (lbs.) ratio (lbs.) trailer-m2 (ft2) 0-Maximum 2-door 4.0L 3.27 3 402 0-1 533 4.64 SOHC (7 500) (0-3 380) (50) 4.0L 3.55 3 856 0-1 978 4.64 SOHC (8 500) (0-4 380) (50) 3.73 4 082 0-2 214 4.64 4.0L OHV (9 000) (0-4 880) (50) 4.0L 3.73 4 082 0-2 214 4.64 SOHC (9 000) (0-4 880) (50) 4.10 4 082 0-2 214 4.64 4.
Driving Trailer towing table (4x4 and AWD with automatic transmission) Notes: For high altitude operation, reduce GCW by 2% per 300 meters (1 000 ft) elevation. For definition of terms and instructions on calculating your vehicle’s load, refer to Vehicle loading in this chapter. Maximum trailer weights shown. The combined weight of the completed towing vehicle and the loaded trailer must not exceed the GCWR. Towing a trailer over 1 588 kg (3 500 lbs.) requires a weight distributing hitch.
Driving Safety chains Always connect the trailer’s safety chains to the vehicle. To connect the trailer’s safety chains, cross the chains under the trailer tongue and allow slack for turning corners. If you use a rental trailer, follow the instructions that the rental agency gives to you. Do not attach safety chains to the bumper. Trailer brakes Electric brakes and manual, automatic or surge-type brakes are safe if installed properly and adjusted to the manufacturer’s specifications.
Driving Driving while you tow Do not drive faster than 88 km/h (55 mph) when towing a trailer. Speed control may shut off if you are towing on long, steep grades. When towing a trailer: • Use a lower gear when towing up or down steep hills. This will eliminate excessive downshifting and upshifting for optimum fuel economy and transmission cooling. • Anticipate stops and brake gradually. Exceeding the GCWR rating may cause internal transmission damage and void your warranty coverage.
Driving Launching or retrieving a boat When backing down a ramp during boat launching or retrieval, • Do not allow the static water level to rise above the bottom edge of the rear bumper and • Do not allow waves to break higher than 15 cm (six inches) above the bottom edge of the rear bumper. Exceeding these limits may allow water to enter critical vehicle components, adversely affecting driveability, emissions, reliability and causing internal transmission damage.
Driving LUGGAGE RACK Maximum load is 90 kg (200 lbs), evenly distributed. If it is not possible to distribute the load, position it as far rearward as possible. Adjustable tie down loops must be used to secure the load. To adjust cross-bar position: 1. Loosen the thumbwheel at both ends of the cross-bar (both cross-bars are adjustable). 2. Slide the cross-bar to the desired location. 3. Tighten the thumbwheel at both ends of the cross-bar. To remove the cross-bar assembly from the roof rack side rails: 1.
Roadside emergencies HAZARD FLASHER Use only in an emergency to warn traffic of vehicle breakdown, approaching danger, etc. The hazard flashers can be operated when the ignition is off. • The hazard lights control is located on top of the steering column. • Depress hazard lights control to activate all hazard flashers simultaneously. • Depress control again to turn the flashers off.
Roadside emergencies The fuel pump shut-off switch is located in the passenger’s foot well, behind the kick panel. FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within the fuse. Check the appropriate fuses before replacing any electrical components. 15 Always replace a fuse with one that has the specified amperage rating.
Roadside emergencies Standard fuse amperage rating and color COLOR Fuse Rating Mini Fuses Standard Fuses Maxi Fuses 2A 3A 4A 5A 7.
Roadside emergencies Passenger compartment fuse panel The fuse panel is located on the left hand side of the instrument panel facing the driver’s side door. Pull the panel cover outward to access the fuses. 28 24 20 16 12 8 4 To remove a fuse use the fuse puller tool provided on the fuse panel cover.
Roadside emergencies The fuses are coded as follows: Fuse/Relay Fuse Amp Description Location Rating 1 7.5A Power Mirror Switch, Power Antenna 2 7.5A Blower Motor Relay, Air Bag Diagnostic Monitor 3 7.5A Left Stop/Turn Trailer Tow Connector 4 10A Left Headlamp 5 10A Data Link Connector (DLC) 6 7.5A Rear Blower Motor (Without EATC) 7 7.5A Right Stop/Turn Trailer Tow Connector 8 10A Right Headlamp, Foglamp Relay 9 7.5A Brake Pedal Position Switch 10 7.
Roadside emergencies Fuse/Relay Fuse Amp Description Location Rating 20 7.5A RAP Module, Generic Electronic Module (GEM), Radio 21 15A Flasher (Hazard) 22 20A Auxiliary Power Socket 23 — Not Used 24 7.5A Clutch Pedal Position (CPP) Switch, Starter Interrupt Relay, Anti-Theft 25 7.
Roadside emergencies Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads. Always disconnect the battery before servicing high current fuses. Always replace the cover to the Power Distribution Box before reconnecting the battery or refilling fluid reservoirs.
Roadside emergencies 9 1 2 14 5 10 8 5 4 10 1 7 3 3 4 9 7 8 2 8 15 2 6 11 12 4 3 10 7 2 6 1 13 6 1 5 9 1 175 MEGAFUSE The high-current fuses are coded as follows: Fuse/Relay Fuse Amp Description Location Rating 1 60A** I/P Fuse Panel 2 40A** Blower Motor Relay 3 50A** 4 Wheel Anti-Lock Brake System (4WABS) Module 4 30A** Power Windows, Power Moon Roof, Power Seat 5 50A** Ignition Switch, Starter Relay 6 20A** Transfer Case Relay 7 — Not Used 8 20A** Automatic Ride Control
Roadside emergencies Fuse/Relay Fuse Amp Location Rating 3 30A* 4 15A* 5 — 6 10A* 7 30A* 8 15A* 9 20A* 10 15A* 11 15A* 12 30A* 13 15A* Description Heated Backlight Fog Lamps and Daytime Running Lamps Not Used Powertrain Control Module 4 Wheel Anti-Lock System (4WABS) Module Rear Wiper Motor Fuel Pump Relay and RAP Module Horn Relay Parklamps Relay and Mainlight Switch Mainlight Switch and Multifunction Switch Heated Oxygen Sensor, EGR Vacuum Regulator, EVR Solenoid, Camshaft Position (CMP) Sensor, Caniste
Roadside emergencies CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily. Instead, gradually decrease your speed. Hold the steering wheel firmly and slowly move to a safe place on the side of the road. Spare tire information Your vehicle is equipped with a 15” spare tire that must be used for emergencies only. Vehicles equipped with 16” tires have a 16” spare tire. The 15” spare tire is not as wide as a regular tire and is designed for emergency use only.
Roadside emergencies Removing the spare tire 1. Insert the jack handle into the rear bumper opening. The handle will stop moving and forward resistance to turning will be felt when properly engaged. 2. Turn the handle counterclockwise until tire is lowered to the ground, the tire can be slid rearward and the cable is slightly slack. 3. Remove the retainer from the spare tire. Stowing the spare 1. Lay the tire on the ground with the valve stem facing up. 2.
Roadside emergencies Refer to the instruction sheet for detailed tire change instructions. 1. Park on a level surface, activate hazard flashers and set the parking brake. 2. Place gearshift lever in P (Park) or in the reverse gear (manual transmission) and turn engine OFF. When one of the rear wheels is off the ground, the transmission alone will not prevent the vehicle from moving or slipping off the jack, even if the transmission is in P (Park) (automatic transmission) or reverse (manual transmission). 3.
Roadside emergencies 6. Turn OFF the air suspension switch (if equipped). Refer to Air suspension system in the Driving chapter. 7. Position the jack according to the following guides and turn the jack handle clockwise until the tire is a maximum of 25 mm (1 inch) off the ground.
Roadside emergencies To lessen the risk of personal injury, do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire. • Never use the front or rear differential as a jacking point. 8. Remove the lug nuts with the lug wrench. 9. Replace the flat tire with the spare tire, making sure the valve stem is facing outward.
Roadside emergencies JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Do not push start your vehicle. You could damage the catalytic converter. Batteries contain sulfuric acid which can burn skin, eyes, and clothing, if contacted. Do not attempt to push start your vehicle. Automatic transmissions do not have push-start capability. Preparing your vehicle 1.
Roadside emergencies Connecting the jumper cables + + – – 1. Connect the positive (+) booster cable to the positive (+) terminal of the discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. + + – – 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery.
Roadside emergencies + + – – 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor. The preferred locations of an exposed metal part (to ground the circuit) are the alternator mounting brackets or an engine lifting eye. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points.
Roadside emergencies • 4.0L SOHC + + – – 5. Be sure that the cables are clear of fan blades, belts and other moving parts of both engines. Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for a further three minutes before disconnecting the jumper cables.
Roadside emergencies Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. • Engines except 4.0L SOHC + – – + + – – 196 + • 4.
Roadside emergencies + + – – 2. Remove the jumper cable on the negative (-) connection of the booster vehicle’s battery. + + – – 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery.
Roadside emergencies + + – – 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions. WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or, if you are a member, your roadside assistance center.
Roadside emergencies If equipped with air suspension, the air suspension control must be turned to the OFF position. The Ford approved towing procedure is flatbed or wheel lift with dollies. On 4x2 vehicles, it is acceptable to tow the vehicle with the front wheels on the ground (without dollies) and the rear wheels off the ground. On 4x4 vehicles, it is recommended that your vehicle be towed with a wheel lift and dollies or flatbed equipment with all the wheels off the ground.
Maintenance and care SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easy location. • We provide a Scheduled Maintenance Guide which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide necessary parts and service. Check your “Warranty Guide” to find out which parts and services are covered.
Maintenance and care • 1. 2. 3. 4. Manual transmission: Set the parking brake. Depress the clutch and place the gearshift in 1 (First). Turn off the engine and remove the key. Block the wheels to prevent the vehicle from moving unexpectedly. Working with the engine on • Automatic transmission: 1. Set the parking brake and ensure the gearshift is securely latched in P (Park). 2. Block the wheels to prevent the vehicle from moving unexpectedly.
Maintenance and care 2. Go to the front of the vehicle and release the auxiliary latch that is located in the center between the hood and the grill. 3. Lift the hood until the lift cylinders hold it open.
Maintenance and care IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.0L OHV V6 engine 1 10 2 3 4 5 9 6 7 8 1. Windshield washer fluid reservoir 2. Engine oil filler cap 3. Transmission fluid dipstick (automatic transmission) 4. Engine oil dipstick 5. Power steering fluid reservoir 6. Brake fluid reservoir 7. Clutch fluid reservoir (manual transmission) 8. Battery 9. Air filter assembly 10.
Maintenance and care 4.0L SOHC V6 engine 1 9 1. 2. 3. 4. 5. 6. 7. 8. 9.
Maintenance and care 5.0L V8 engine 2 3 4 5 1 9 1. 2. 3. 4. 5. 6. 7. 8. 9. 8 7 6 Engine coolant reservoir Windshield washer fluid reservoir Engine oil filler cap Automatic transmission fluid dipstick Brake fluid reservoir Battery Power steering fluid reservoir Engine oil dipstick Air filter assembly ENGINE OIL Checking the engine oil Refer to the Scheduled Maintenance Guide for the appropriate intervals for checking the engine oil . 1. Make sure the vehicle is on level ground. 2.
Maintenance and care 4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove the engine oil level indicator (dipstick). • 4.0L V6 engines FULL ADD 1 QT • 5.0L V8 engine MIN MAX 6. Wipe the indicator clean. Insert the indicator fully, then remove it again. • If the oil level is between the ADD and FULL marks (4.0L engines) or between the MIN and MAX marks (5.0L engine), the oil level is acceptable. DO NOT ADD OIL.
Maintenance and care • If the oil level is below the ADD mark (4.0L engines) or MIN mark (5.0L engine), add enough oil to raise the level within the ADD-FULL range (4.0L engines) or MIN-MAX range (5.0L engine). • Oil levels above the letter F in FULL (4.0L engines) or the MAX mark (5.0L engine) may cause engine damage. Some oil must be removed from the engine by a service technician. 7. Put the indicator back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil.
Maintenance and care Do not use supplemental engine oil additives, oil treatments or engine treatments. They are unnecessary and could, under certain conditions, lead to engine damage which is not covered by your warranty. Change your engine oil and filter according to the appropriate schedule listed in the Scheduled Maintenance Guide. Ford production and aftermarket (Motorcraft) oil filters are designed for added engine protection and long life.
Maintenance and care Brake fluid is toxic. If you use a brake fluid that is not DOT 3, you will cause permanent damage to your brakes. Do not let the reservoir for the master cylinder run dry. This may cause the brakes to fail. CLUTCH FLUID (IF EQUIPPED) Check the clutch fluid level. Refer to the Scheduled Maintenance Guide for the service interval schedules. During normal operation, the fluid level in the clutch reservoir should remain constant.
Maintenance and care WINDSHIELD WASHER FLUID SHER FL WA UID Checking and adding washer fluid Check the washer fluid whenever you stop for fuel. The reservoir is highlighted with a symbol. If the level is low, add enough fluid to fill the reservoir. In very cold weather, do not fill the reservoir all the way. ONLY RADIATOR COOLANT ONLY Do not put engine coolant in the container for the windshield washer fluid.
Maintenance and care If the engine coolant has not been checked at the recommended interval, the engine coolant reservoir may become empty. If this occurs, add engine coolant to the reservoir. For more information on engine coolant maintenance, refer to Adding engine coolant in this chapter. Automotive fluids are not interchangeable; do not use engine coolant, antifreeze or windshield washer fluid outside of its specified function and vehicle location.
Maintenance and care If you must remove the coolant reservoir cap, follow these steps to avoid personal injury: 1. Before you remove the cap, turn the engine off and let it cool. 2. When the engine is cool, wrap a thick cloth around the cap. Slowly turn cap counterclockwise until pressure begins to release. 3. Step back while the pressure releases. 4. When you are sure that all the pressure has been released, use the cloth to turn it counterclockwise and remove the cap.
Maintenance and care For vehicles with orange coolant, no recycling process has been approved at this time and use of such coolant may harm engine and cooling system components. Always dispose of used automotive fluids in a responsible manner. Follow your community’s regulations and standards for recycling and disposing of automotive fluids. Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, refer to Refill capacities in the Capacities and specifications chapter.
Maintenance and care • 4.0L OHV V6 engine • 4.0L SOHC V6 engine DO N OW FLUIDEER ER ST • 5.
Maintenance and care 1. Start the engine and let it run until it reaches normal operating temperature (the engine coolant temperature gauge indicator will be near the center of the normal area between H and C). 2. While the engine idles, turn the steering wheel left and right several times. 3. Turn the engine off. 4. If your vehicle is equipped with a 4.0L OHV V6 engine, check the fluid level on the dipstick. It should be within the FULL HOT range. Do not add fluid if the level is within this range. 5.
Maintenance and care 5. Remove the dipstick, wiping it clean with a clean, dry lint free rag. 6. Install the dipstick making sure it is fully seated in the filler tube. 7. Remove the dipstick and inspect the fluid level. The fluid should be in the designated areas for normal and room temperature. Correct fluid level The transmission fluid should be checked at normal operating temperatures 66°C-77°C (150°F-170°F) on a level surface.
Maintenance and care Use of a non-approved automatic transmission fluid may cause internal transmission component damage. If necessary, add fluid in 250 mL (1/2 pint) increments through the filler tube until the level is correct. If an overfill occurs, excess fluid should be removed by a qualified ADD COLD HOT DO NOT ADD technician. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. Checking and adding manual transmission fluid 1.
Maintenance and care 3. Fluid level should be at bottom of the opening. 4. Add enough fluid through the filler opening so that the fluid level is at the bottom of the opening. 5. Install and tighten the fill plug securely. Use only fluid that meets Ford specifications. Refer to the Capacities and specifications chapter. Checking and adding transfer case fluid 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level.
Maintenance and care 3. Add only enough fluid through the filler opening so that the fluid level is at the bottom of the opening. Use only fluid that meets Ford specifications. Refer to the Capacities and specifications chapter. DRIVELINE UNIVERSAL JOINT AND SLIP YOKE Your vehicle may be equipped with universal joints that require lubrication. Refer to the Scheduled Maintenance Guide for maintenance intervals.
Maintenance and care If the electrolyte level in the battery is low, you can add plain tap water to the battery, as long as you do not use hard water (water with a high mineral or alkali content). If possible, however, try to only fill the battery cells with distilled water. If the battery needs water often, have the charging system checked. If your battery has a cover/shield, make sure it is reinstalled after the battery has been cleaned or replaced.
Maintenance and care RN LE TU AD RE 1. Set your parking brake. 2. Put the gearshift in P (Park) (automatic transmission) or the neutral position (manual transmission), turn off all accessories and start the engine. 3. Let the engine idle for at least one minute. 4. The relearning process will automatically complete as you drive the vehicle. • The vehicle may need to be driven 16 km (10 miles) or more to relearn the idle and fuel trim strategy.
Maintenance and care Changing the wiper blades To replace the wiper blades: 1. Pull the wiper arm away from the windshield and lock into the service position. 2. Turn the blade at an angle from the wiper arm. Push the lock pin manually to release the blade and pull the wiper blade down toward the windshield to remove it from the arm. 3. Attach the new wiper to the wiper arm and press it into place until a click is heard.
Maintenance and care Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1/2) times as well on the government course as a tire graded 100.
Maintenance and care SERVICING YOUR TIRES Checking the tire pressure • Use an accurate tire pressure gauge. • Check the tire pressure when tires are cold, after the vehicle has been parked for at least one hour or has been driven less than 5 km (3 miles). • Adjust tire pressure to recommended specifications found on the Safety Compliance Certification Label, located on the drivers door jamb.
Maintenance and care • 16’’ Five tire rotation Replacing the tires Replace the tires when the wear band is visible through the tire treads. When replacing full size tires, never mix radial, bias-belted, or bias-type tires. Use only the tire sizes that are listed on the tire pressure decal. Make sure that all tires are the same size, speed rating, and load-carrying capacity. Use only the tire combinations recommended on the decal.
Maintenance and care Do not replace your tires with “high performance” tires or larger size tires. Failure to follow these precautions may adversely affect the handling of the vehicle and make it easier for the driver to lose control and roll over. Tires that are larger or smaller than your vehicle’s original tires may also affect the accuracy of your speedometer. USING SNOW TIRES AND TRACTION DEVICES Snow tires must be the same size and grade as the tires you currently have on your vehicle.
Maintenance and care Consult your dealer for information on other Ford approved methods of traction control. WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire. If you do not use the proper fuel cap, the pressure in the fuel tank can damage the fuel system or cause it to work improperly in a collision. The fuel system may be under pressure.
Maintenance and care • Avoid inhaling fuel vapors. Inhaling too much fuel vapor of any kind can lead to eye and respiratory tract irritation. In severe cases, excessive or prolonged breathing of fuel vapor can cause serious illness and permanent injury. • Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes, remove contact lenses (if worn), flush with water for 15 minutes and seek medical attention. Failure to seek proper medical attention could lead to permanent injury.
Maintenance and care Octane recommendations Your vehicle is designed to use “Regular” unleaded gasoline with an (R+M)/2 octane rating of 87. We do not recommend the use of gasolines (R+M)/2 METHOD labeled as “Regular” that are sold with octane ratings of 86 or lower in high altitude areas. Do not be concerned if your engine sometimes knocks lightly.
Maintenance and care Running out of fuel Avoid running out fuel because this situation may have an adverse affect on powertrain components. If you have run out of fuel: • You may need to crank the engine several times before the system starts to pump fuel from the tank to the engine. • Your “Check Engine” light may come on. For more information on the “Check Engine” light, refer to the Instrumentation chapter.
Maintenance and care If you do not use the proper fuel filler cap, the pressure in the fuel tank can damage the fuel system or cause it to work improperly in a collision. Fuel Filter Your vehicle is equipped with a fuel filter that is mounted on the underbody. For fuel filter replacement, see your dealer or a qualified service technician. Refer to the Scheduled Maintenance Guide for the appropriate intervals for changing the fuel filter.
Maintenance and care Filling the tank For consistent results: • Use the same filling rate setting (low — medium — high) each time the tank is filled. • Allow three automatic click-offs when filling. • Always use the recommended octane rating of a known quality gasoline, preferably a national brand. • Use the same side of the same pump and have the vehicle facing the same direction each time you fill up. • Have the vehicle loading and distribution the same every time.
Maintenance and care Habits • Smooth, moderate operation can yield up to 10% savings in fuel. • Steady speeds without stopping will usually give the best fuel economy. • Idling for long periods of time (greater than one minute) may waste fuel. • Anticipate stopping; slowing down may eliminate the need to stop. • Sudden or hard accelerations may reduce fuel economy. • Slow down gradually. • Drive at reasonable speeds (traveling at 105 km /h [65 mph] uses 15% more fuel than traveling at 88 km/h [55 mph]).
Maintenance and care Conditions • Heavily loading a vehicle or towing a trailer may reduce fuel economy at any speed. • Carrying unnecessary weight may reduce fuel economy (approximately 2 km/h [1 mpg] is lost for every 180 kg [400 lb] of weight carried). • Adding certain accessories to your vehicle (for example bug deflectors, rollover/light bars, running boards, ski/luggage racks) may reduce fuel economy. • Use of fuel blended with alcohol may lower fuel economy.
Maintenance and care • Do not turn off the ignition while your vehicle is moving, especially at high speeds. • Have the items listed in your Scheduled Maintenance Guide performed according to the specified schedule. The scheduled maintenance items listed in the Scheduled Maintenance Guide are essential to the life and performance of your vehicle and to its emissions system.
Maintenance and care Readiness for inspection/maintenance (I/M) testing In some localities, it may be a legal requirement to pass an I/M test of the on-board diagnostic (OBD-II) system. If your “Check Engine/Service Engine Soon” light is on, refer to the description in the Warning Lights and Chimes section of the Instrumentation chapter. Your vehicle may not pass the I/M test with the “Check Engine/Service Engine Soon” light on.
Maintenance and care Replacing headlamp bulbs Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated. If the bulb is accidentally touched, it should be cleaned with rubbing alcohol before being used. To remove the headlamp bulb: 1. Make sure headlamp switch is in OFF position, then lift hood and open the hinged headlamp cover.
Maintenance and care To install the new bulb: 1. With the flat side of the new bulb’s plastic base facing upward, insert the glass end of the bulb into the lamp assembly. You may need to turn the bulb left or right to align the grooves in the plastic base with the tabs in the lamp assembly. When the grooves are aligned, push the bulb into the lamp assembly until the plastic base contacts the rear of the lamp assembly. 2.
Maintenance and care Replacing tail lamp/backup lamp bulbs The tail lamp/backup lamp bulbs are located in the same portion of the tail lamp assembly, one just below the other. Follow the same steps to replace either bulb: 1. Open the liftgate to expose the lamp assemblies. 2. Remove the two screws from the lamp assembly. 3. Carefully remove the lamp assembly by pulling it rearward. 4. Twist the bulb socket 1⁄4 turn counterclockwise and remove from lamp assembly. 5.
Maintenance and care License plate lamp bulbs To change the license plate bulbs: 1. Remove two screws and the license plate lamp assembly from the liftgate. 2. Pull the bulb out from lamp assembly and push in the new bulb. 3. Install the lamp assembly on liftgate with two screws. High-mount brakelamp bulbs For bulb replacement, see a dealer or qualified technician.
Maintenance and care AIMING THE HEADLAMPS The alignment of your headlamps should be checked by a qualified service technician if: • Oncoming motorists frequently signal you to deactivate your high beams, and your high beams are not activated. • The headlamps do not seem to provide enough light for clear night vision. • The headlamp beams are pointed substantially away from a slightly down and to the right position.
Maintenance and care Waxing your vehicle Wax when water stops beading on the surface. This could be every three or four months, depending on operating conditions. Use only carnauba or synthetic-based waxes. Use cleaning fluid or alcohol with a clean cloth to remove any bugs and tar before waxing vehicle. Use tar remover to remove any tar spots. Avoid getting wax on the windshield.
Maintenance and care • 5.0L • 4.
Maintenance and care • 4.0L OHV • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. Cleaning the wheels Wash with the same detergent as the body of your vehicle. Do not use acid-based or alcohol-based wheel cleaners, steel wool, fuel or strong detergents. Never use abrasives that will damage the finish of special wheel surfaces. Use a tar remover to remove grease and tar. Underbody Flush the complete underside of vehicle frequently.
Maintenance and care Cleaning the wiper blades and windshield If the wiper blades do not wipe properly, clean the wiper blade rubber element with undiluted windshield washer solution or a mild detergent. To avoid damaging the blades, do not use fuel, kerosene, paint thinner or other solvents. If the wiper still does not wipe properly, this could be caused by substances on the windshield such as tree sap and some hot wax treatments used by commercial car washes.
Maintenance and care Cleaning the interior fabric Remove dust and loose dirt with a whisk broom or a vacuum cleaner. Remove fresh spots immediately. Do not use household or glass cleaners. These agents can stain and discolor the fabric. Use a mild soap and water solution if necessary. Cleaning and maintaining the safety belts Clean the safety belts with a mild soap solution recommended for cleaning upholstery or carpets. Do not bleach or dye the belts, because these actions may weaken the belt webbing.
Capacities and specifications MOTORCRAFT PART NUMBERS Component Air filter Fuel filter Battery Oil filter PCV valve Spark plugs* 4.0L OHV V6 engine FA-1658 FG-986B BXT-65-650 FL-1A EV-225 AGRF-22P 4.0L SOHC V6 engine FA-1658 FG-986B BXT-65-650 FL-1A EV-225 AGRF-22P 5.0L V8 engine FA-1658 FG-986B BXT-65-650 FL-820S EV-152 AWSF-32EE * Refer to Vehicle Emissions Control Information (VECI) decal for spark plug gap information.
Capacities and specifications Fluid Ford Part Application Name Transmission Motorcraft 5-speed fluid MERCONt ATF manual 4R70W Automatic with 5.0L V8 engine 5R55E Automatic with 4.0L V6 engine (4x2) 5R55E Automatic with 4.0L V6 engine (4x4) Transfer case Motorcraft 4WD MERCONt ATF AWD 4.0L OHV V6 Engine coolant1 See footnote engine 4.0L SOHC V6 engine 5.0L V8 engine Front axle fluid Motorcraft SAE 4x4 vehicles 80W90 Premium Rear Axle Lubricant 248 Capacity 2.6L (5.6 pints) 13.1L (13.9 quarts) 9.5L (10.
Capacities and specifications Fluid Rear axle lubricant2, Windshield washer fluid Ford Part Name Motorcraft SAE 80W90 Premium Rear Axle Lubricant Motorcraft SAE 75W140 High Performance Synthetic Rear Axle Lubricant Ultra-Clear Windshield Washer Concentrate Application Capacity Refer to footnote 3 Refer to footnote 4 2.9-3.1L (5.5-5.8 pints) All 2.6L (2.7 quarts) 1 If your engine coolant is green in color, use Ford Premium Cooling System Fluid.
Capacities and specifications LUBRICANT SPECIFICATIONS Item Ford Part Name or equivalent Body hinges, latches, door striker plates and rotors, seat tracks, fuel filler Multi-Purpose door hinge and Grease spring, hood latch, auxiliary latch, seat tracks High Hydraulic clutch Perfromance fluid and brake DOT 3 Motor fluid Vehicle Brake Fluid Driveshaft, slip Premium Long spline, universal Life Grease joints Engine coolant1 Ford Premium Engine Coolant (green in color) Ford Extended Life Engine Coolant (orang
Capacities and specifications Item Power steering fluid Ford conventional and Traction-Lok rear axles Front axle Transfer case Four wheel drive 5-speed manual transmission Transfer case Front Output Slip Shaft Windshield washer fluid Ford Part Name or equivalent Motorcraft MERCON tATF Ford Part Number Ford Specification XT-2-QDX MERCONt 2, 3, 4 2, 3, 4 2, 3, 4 4x4 Gear Oil F1TZ-19580-A WSL-M2C191-A Motorcraft MERCONt ATF XT-2-QDX MERCONt Motorcraft MERCONt ATF XT-2-QDX MERCONt Premium Long
Capacities and specifications ENGINE DATA Engine Cubic inches Horsepower Torque Recommended fuel Firing order Spark plug gap Ignition system Compression ratio 4.0L OHV V6 engine 245 160 @ 4200 rpm 225 lb.-ft. @ 2750 rpm 87 octane 4.0L SOHC V6 engine 245 210 @ 5250 rpm 240 lb.-ft. @ 3250 rpm 87 octane 302 215 @ 4200 rpm 288 lbs.ft. @ 3300 rpm 87 octane 1-4-2-5-3-6 1.3-1.4 mm (0.052-0.056 inch) EDIS 9.0:1 1-4-2-5-3-6 1.3-1.4 mm (0.052-0.056 inch) EDIS 9.7:1 1-3-7-2-6-5-4-8 1.3-1.4 mm (0.052-0.
Capacities and specifications Dimensions (1) Overall length (2) Overall width (3) Maximum height (4) Wheelbase (5) Front track (5) Rear track 4-Door 4x2 XL Model mm (in.) 4 857 (191.2) 1 783 (70.2) 1 719 (67.7) 4-Door 4x4 XLT Model mm (in.) 4 857 (191.2) 1 783 (70.2) 1 793 (70.6)* 2 835 (111.6) 1 486 58.5) 1 487 (58.5) 2 835 (111.6) 1 486 (58.5) 1 487 (58.
Capacities and specifications 3 5 2 IDENTIFYING YOUR VEHICLE Safety compliance label The National Highway Traffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located. The Safety Compliance Certification Label is located on the front door latch pillar on the driver’s side. MFD. BY FORD MOTOR CO. IN U.S.A.
Capacities and specifications Vehicle identification number The vehicle identification number is attached to a metal tag and is located on the driver side instrument panel. AIR BAG XXXXXXXXXXXXXXXXX Engine number The engine number (the last eight numbers of the vehicle identification number) is stamped on the engine block, transmission, frame and transfer case (if equipped).
Reporting safety defects REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect that could cause a crash, or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Index Air bag supplemental restraint system ........................................126 and child safety seats ............128 description .......................127,130 disposal ....................................133 indicator light ..................130,132 passenger air bag ............128,131 Air conditioning automatic temperature control system .23,24,25,26,27,28 rear seat controls .....................29 Air suspension description ..............................148 warning light ......................
Index Engine oil checking and adding ..............207 dipstick ....................................205 specifications ...................205,207 Exhaust fumes ..........................143 Floor mats .................................103 Four-Wheel Drive vehicles ..............................9,10,157 control trac .............................157 description .......................157,159 driving off road ................160,162 electronic shift ..........................31 Fuel choosing the right fuel ....
Index speed control ............................84 turn signal indicator ...................8 Locks childproof ................................100 Lumbar support, seats ......116,118 Manual transmission reverse .....................................156 Message center ...........................15 economy button ........................16 english/metric button ..........15,16 reset button ..............................16 system check button ...........17,18 Mirrors automatic dimming rearview mirror ..........
Index Transmission ......................149,215 automatic operation ...............149 fluid, checking and adding (automatic) ......................215,216 fluid, checking and adding (manual) .................................217 manual operation ....................154 Trip odometer .............................13 Universal transmitter (see garage door opener) ....92,93,94,95 Vehicle dimensions ...................252 Vehicle Identification Number (VIN) ..........................................
Filling station information Item Information Recommended fuel Unleaded fuel only - 87 octane Fuel tank capacity (2 door) 65.5L (17.3 gallons) Fuel tank capacity (4 door) 78.7L (20.8 gallons) Engine oil capacity (includes filter 4.7L (5.0 quarts). Use Motorcraft change) 5W30 Super Premium Motor Oil, Ford specification WSS-M2C153-G. Tire size and pressure See Safety Compliance Certification Label on inside of driver door. Hood release Pull handle under the instrument panel. Coolant capacity-(4.0L OHV V6 11.
Filling station information 2 Ensure correct automatic transmission fluid is used for a specific application. Check the container to verify the fluid is MERCONt and/or MERCONt V approved. Some fluids have been approved as meeting both MERCONt and MERCONt V requirements and will be labeled as such. Fluids labeled as meeting only MERCONt or only MERCONt V requirements must not be used interchangeably. DO NOT mix MERCONt and MERCONt V.
